2012 Na Yamaha Super Tenere Manual

							
haha BASIC SERVICE INFORMATION
1-42
4. Connect: Lead
 Coupler
 Connector
TIP
When connecting a coupler or connector, push 
both sections of the coupler or connector to-
gether until they are connected securely.
Make sure all connections are tight.
5. Check: Continuity
(with the pocket tester)
TIP
If there is no continuity, clean the terminals.
 When checking the wire harness, perform 
steps (1) to (4). 
As a quick remedy, use a contact revitalizer 
available at most part stores.
  Pocket tester
90890-03112
Analog pocket tester YU-03112-C      
						

							
haha SPECIAL TOOLS
1-43
EAS20260
SPECIAL TOOLS
The following special tools are necessary for complete and accurate tune-up and assembly. Use only 
the appropriate special tools as this will help prevent damage caused by the use of inappropriate tools 
or improvised techniques. Special tools, part numbers or both may differ depending on the country.
When placing an order, refer to the list provided below to avoid any mistakes.
TIP
 For U.S.A. and Canada, use part number starting with  “YM- ”, “ YU- ”, or  “ACC- ”.
For others, use part number starting with  “90890- ”.
Tool name/Tool No. Illustration Reference 
pages
Test coupler adapter
90890-03149 1-25, 4-71, 
4-72
Pocket tester
90890-03112
Analog pocket tester
YU-03112-C 1-42, 8-120, 
8-121, 8-129, 
8-130, 8-131, 
8-135, 8-136, 
8-137, 8-138, 
8-139, 8-140, 
8-141, 8-142, 
8-143, 8-144, 
8-145, 8-146
Thickness gauge
90890-03180
Feeler gauge set
YU-26900-9 3-6, 5-60
Valve lapper
90890-04101
Valve lapping tool
YM-A8998 3-6
Vacuum gauge
90890-03094
Vacuummate
YU-44456 3-9
YU-44456      
						

							
haha SPECIAL TOOLS
1-44
Carburetor angle driver 2
90890-03173 3-9
Steering nut wrench
90890-01403
Exhaust flange nut wrench
YU-A9472 3-19, 4-93
Oil filter wrench
90890-01426
YU-38411 3-24, 5-86
Oil pressure gauge set
90890-03120
Fuel & oil pressure gauge
YM-03153 3-26
Oil pressure adapter B
90890-03124 3-26
Fork spring compressor
90890-01441
YM-01441 4-84, 4-89
Damper rod holder
90890-01423
Damping rod holder
YM-01423 4-85, 4-87
Fork seal driver
90890-01442
Adjustable fork seal driver (36 –46 mm)
YM-01442 4-86, 4-87
Tool name/Tool No. Illustration
Reference 
pages         
						

							
haha SPECIAL TOOLS
1-45
Rod puller
90890-01437
Universal damping rod bleeding tool set
YM-A8703 4-88
Rod puller attachment (M10)
90890-01436
Universal damping rod bleeding tool set
YM-A8703 4-88
Ring gear fix bolt (M14)
90890-01548
YM-01548 4-109
Final gear backlash band
90890-01511
Middle drive gear lash tool
YM-01230 4-109
Coupling gear holding tool
90890-01560
YM-01560 4-111, 4-115
Bearing retainer wrench
90890-01561
YM-01561 4-111, 4-115
Tool name/Tool No. Illustration
Reference 
pages
YM-A8703
YM-A8703
ø75ø65 6.0      
						

							
haha SPECIAL TOOLS
1-46
Fork seal driver weight
90890-01367
Replacement hammer
YM-A9409-7 4-117
Fork seal driver attachment ( ø30)
90890-01400
Replacement 31 mm
YM-A94093 4-117
Fork seal driver attachment ( ø38)
90890-01372
Replacement 38 mm
YM-A5142-1 4-117
Extension
90890-04136 5-1
Compression gauge
90890-03081
Engine compression tester
YU-33223 5-1
Pivot shaft wrench
90890-01485
Frame mount insert wrench
YM-01485 5-9
Rotor holding tool
90890-01235
Universal magneto & rotor holder
YU-01235 5-17, 5-20
Yamaha bond No. 1215
90890-85505 5-23, 5-46, 
5-87
Tool name/Tool No. Illustration
Reference 
pages
YM-A9409-7/YM-A5142-4         
						

							
haha SPECIAL TOOLS
1-47
Valve spring compressor
90890-04019
YM-04019 5-29, 5-34
Valve spring compressor attachment
90890-01243
Valve spring compressor adapter (26 mm)
YM-01253-1 5-29, 5-34
Valve guide remover & installer set (ø 5.5)
90890-04016
Valve guide remover (5.5 mm)
YM-01122 5-31
Valve guide installer ( ø5.5)
90890-04015
Valve guide installer (5.5 mm)
YM-04015 5-31
Valve guide reamer (5.5 mm)
90890-01196
YM-01196 5-31
Piston pin puller set
90890-01304
Piston pin puller
YU-01304 5-37
Sheave holder
90890-01701
Primary clutch holder
YS-01880-A 5-44, 5-45, 
5-69
Flywheel puller
90890-01362
Heavy duty puller
YU-33270-B 5-44
Tool name/Tool No.
IllustrationReference 
pages
YU-01304          
						

							
haha SPECIAL TOOLS
1-48
Digital circuit tester
90890-03174
Model 88 Multimeter with tachometer
YU-A1927 5-49
Universal clutch holder
90890-04086
YM-91042 5-59, 5-62
Slide hammer bolt
90890-01083
Slide hammer bolt 6 mm
YU-01083-1 5-108
Weight
90890-01084
YU-01083-3 5-108
Universal joint holder
90890-04160
YM-04062 5-116, 5-118
Damper spring compressor
90890-04090
Middle drive gear damper spring com-
pressor
YM-33286 5-116, 5-118
Tool name/Tool No. Illustration
Reference 
pages
YU-01083-3
90890-04160
25
20
3025
30
2420
24       
						

							
haha SPECIAL TOOLS
1-49
Middle drive shaft nut wrench (55 mm)
90890-04054
Offset wrench 55 mm
YM-04054 5-117
Middle gear bachlash tool
90890-04080
Middle drive gear holder
YM-33222 5-120
Radiator cap tester
90890-01325
Mityvac cooling system tester kit
YU-24460-A 6-3
Radiator cap tester adapter
90890-01352
Pressure tester adapter
YU-33984 6-3
Mechanical seal installer
90890-04132
Water pump seal installer
YM-33221-A 6-9
Tool name/Tool No. Illustration
Reference 
pages
YM-04054
YU-24460-A
YU-33984       
						

							
haha SPECIAL TOOLS
1-50
Middle driven shaft bearing driver
90890-04058
Middle drive bearing installer 40 & 50 mm
YM-04058 6-9
Pressure gauge
90890-03153
YU-03153 7-11, 7-12
Fuel injector pressure adapter
90890-03210
YU-03210 7-11
Fuel pressure adapter
90890-03176
YM-03176 7-12
Ignition checker
90890-06754
Oppama pet-4000 spark checker
YM-34487 8-138
Test harness- lean angle sensor (6P)
90890-03209
YU-03209 8-139
Test harness S- pressure sensor (3P)
90890-03207
YU-03207 8-144
Tool name/Tool No. Illustration
Reference 
pages     
						

							
haha SPECIAL TOOLS
1-51