Amptron ASTB2006 user manual

							DC POWER SOURCE
4 x 6 volt 150 Amp/Hr Batteries  (not supplied)
Battery shelf with cables fitted with post connectors for easy installation. Power supply: 2 independent  6 volt and one 12 volt linear regulators with current limit set at 5 amp and Voltage at 6.9-13.8 V wired to keep the batteries 
always fully charged. (On /off switch for manual use)With active convection cooling
REGULATOR TEST
Range:   12 / 24 / 32 Volt
Meter:  0-50Volt Analog 
& Digital 6  wire  system 
Din  plug  with  harness
DIODE TEST
Test Voltage 99 V pp
Green LED:  goodRed LED:     Faulty
LOW RESISTANCE METER
      Analog & Digital
3 Ranges:  1  10  100 Ohm1 milli Ohm resolutionSet zero & over range LED
ALTERNATOR OUTPUT
            CURRENT
   0- 200 A  Analog & Digital
With normal and reverse
selector switch
BATTERY VOLTAGE
Range:  0-30 Volt Analog & Digital
ALTERNATOR 
FAULT LAMPS
6, 12, or 24 V
VOLTAGE SELECTOR
Range:  6, 12 or 24 V
REV COUNTER
Range: 0-6000 RPM  Digital only
DRIVE SYSTEM
Programable computerised drive 
system.    Rotation:   FWD & REV Switch Stop & start  buttons with soft  start  feature  active.  Motor  7.5 KW    Motor  pulley  flat  &  V  diameter:   105 mm  Belt  driven with tension lever Right H  side
  With normal and 
 reverse selector 
STARTER CURRENT
Dinse socket & plug
Range:  0 - 2000AAnalog & Digital
ALTERNATOR LOAD
30 Blocks 0 - 500 A 
variable carbon pile 
STARTER VOLTAGE
Manual selected: HD Dinse socket
 & plug. Range: 6, 12 or 24 Volt
BRAKING DEVICE
225mm Diam caliper disk brake 
hydraulic foot pedal operation.
ACCESSORIES & TOOLS
2 Ring gears as selected
1 Flange for small starters2 V blocks with adaptors1 chain clamp for viceTest leads included
 ALTERNATOR STARTER TEST BENCH
 ASTB2006  
DESIGNED AND MANUFACTURED IN SOUTH AFRICA
Digital only
EXTERNAL VOLTMETER
Measurements done: analog and digital simultaneously display units: 
Analog 109 x 66 Digital 4 digit 96 x 48 range 99.99 V   2000 or 200.0 A
     
Appearance And specifications listed in this brochure are subject to change without notice
INDICATING INSTRUMENTS
  UNIT DIMENSIONS H x W x D 
1590 x 1770 x 1140  MASS: ± 620 Kg   
SOLENOID VOLTAGE
   Manual  push  button 
   energize  solenoid    overload MCB 63 A 
   Range:  6 12 or 24 V 
TORQUE MEASUREMENT
Display: 4 Digit LED 
reading Newton metreLoad cell: 500 Kg Measure running & lock  torque
FIELD CURRENT SUPPLY
Voltage range: 13.8 V fixed
Current range: 0-5 A variable
Meter: 0 - 10 Amperes Analog only
AC POWER  SOURCE
Voltage:         380 Volt AC
Phases:          3 PhaseFrequency:    50 HertzPower consumption:   7.5KWMains switch: 3 pole 25 A MCB
Mains lead:    5 metre 2.5 sq5 Wire with earth & neutral
ADDITIONAL ACCESS.  OPT.
Ring gear  109 teeth  14DP
Ring gear  109 teeth  12DPRing gear    92 teeth  MOD2.5Ring gear    91 teeth  10DPRing gear    77 teeth  MOD3Ring gear    73 teeth  8DPRing gear    66 teeth  MOD3.5Ring gear    54 teeth  6DPRing gear    51 teeth 4.5 MODMPTRONA