AOC Le24h067 User Manual

							20
5. Search TV channel 
Start Initial Wizard (6/8)
Please check if RF cable is
connected properly...
Previous Cancel
Navigate: Select: OK
1Press ▲/▼ to select “Previous” or “Cancel” for RF Tuning setting. Press OK will execute channel searching. 
CH 100 Initial Wizard (7/8)
Searching, Please wait...
Searching Analog CH
66 Analog Channels Found
55 Digital Channels Found
100%
Cancel
Navigate: Select: OK
1Press ▲/▼ to select “Cancel” for RF Tuning setting. Press OK will execute cancel the channel searching. 
Initial Wizard (8/8)
Congratulations, TV Setup is done.
Exit: Cancel
1MU
/ ExitENPress MENU/EXIT to exit initial setting wizard. 
 
						

							21
Viewing Mode Selection
For TV input with SD programs
Normal Mode
Suitable for viewing conventional 4:3 programs in 
their normal format.
Zoom1 Mode
Use these aspect modes to zoom in and to reduce 
the black bars.
Wide Mode
The original content in this mode has to fill the 
entire screen of the display.
Zoom2 Mode
Use these aspect modes to zoom in and to reduce 
the black bars.
For TV input with HD programs
Normal Mode
Suitable for viewing conventional 4:3 programs in 
their normal format.
Zoom1 Mode
Use these aspect modes to zoom in and to reduce 
the black bars.
Wide Mode
The original content in this mode has to fill the 
entire screen of the display.
Zoom2 Mode
Use these aspect modes to zoom in and to reduce 
the black bars.
Note:
HDMI PC Mode (Only available in HDMI input)
Displays an image with the same number of pixels on the screen without over scan.
 
						

							22
Switching Input Source
On AOC TV, you can choose signal source on the remote control directly, or press “Source” to choose the signal source on the display menu.
When choosing signal source on the remote control 1.   directly: Press the following keys to switch input source.
!
MTS
CC
PRE CH
Display
EPGWide
Add Fav
COMP
FavMU
/ ExitEN
COMP
When using “Source 2.  ” key to choose signal source:
OKMENU
/Exit
0. TV
1. AV
2. Component
3. VGA
4. HDMI 1
5. HDMI 2 Source List
Move Select Exit
    
!
MTS
CC
PRE CH
Display
EPGWide
Add Fav
COMP
FavMU
/ ExitEN
1Press Source to call out source menu.
2
Press ▲/▼ to select input source: TV, AV, Component, VGA, HDMI1/ 2.
3
Press OK to enter. 
 
						

							23
OSD Manual Setting 
Channel Search 
OKMENU
/Exit
CHANNEL
Move Select Return ExitChannel Strength
Auto CH Search
Channels ListAdd on CH Search
Channel Labels
FAV Channel SettingCable
Tuning Band
1MU
/ ExitENPress MENU to call out MENU.
2
Press ▲/▼ to select “Channel” , and press OK.
3
Press ▲/▼ to select “Auto CH Search”, and then press OK.
The submenu of CHANNEL menu in TV mode shows as below.
1) Tuning Band: Select TV source signal from the Air (antenna) or Cable (CATV).
2) Channel Strength: Show the intensity of the received DTV signal.
3) Auto CH Search:  Automatically scan all NTSC / ATSC TV channels and then store in the channel table. In channel scan process, the OSD 
can display the number of channels which had been found.
4) Add on CH Search: Add channels which are new found.
5) Channels List: Show the Channels List. User can edit (add/delete) the channel numbers.
6) Channel Labels: Show the NTSC /ATSC TV Channel Labels menu for user modifying channel labels specifically.
7) FAV Channel Settings: Show the Favorite Channel List. User can edit (add/delete) the favorite channels.
 
						

							24
Changing Channel/Flashback
On AOC TV, you can change channel on the remote control directly, or press CH ▲/▼ on the side of the TV to choose the channel.
Press the number keys directly to change the channel. 1. 

PR
Press the  2. CH to change channel.
 
Press  3. PRE CH to go to the previous channel.
 
! PRE CH
 
						

							25
Changing Volume, Mute and Sound Mode
Press  1. VOL to change the volume.
 
Press  2. MUTE to mute the TV.
 
Press  3. Audio to change surround mode: Music, Speech and Personal.
 
For more details, please refer to “Adjust Audio Setting”.
 
						

							26
Adjust Video Setting
OKMENU
/Exit
VIDEO
Move Select Return ExitBrightness
Contrast
Color Sharpness
Tint
Color TempEco
63 50 48
48
0
Cool Picture Mode
1MU
/ ExitENPress MENU/EXIT to call out MENU.
2
Press ▲/▼ to select “VIDEO” , and press OK.
3
Press ▲/▼ to select Video Settings: Picture Mode, Brightness, Contrast, Sharpness, Color, Tint, Color Temp, Noise 
Reduction, Adaptive Contrast, DCR, Backlight, Aspect Ratio, Preset, and press OK to enter.
4
Press ◄/► to adjust.
5
MU
/ ExitENPress MENU/EXIT again to exit.
Picture Setting Items Description
Picture ModeVivid  For Enhances picture contrast and sharpness. 
Standard For standard picture settings. Recommended for home entertainment.
Eco  Decrease backlight level to save the power consumption.
Movie For viewing film-based content. Most suitable for viewing in a theater-like environment.
Personal The user can set their favorite setting.
Preset for all inputs can also be accessed by pressing Picture on the remote control to directly toggle the modes.
BrightnessBrightens or darkens the picture.
ContrastIncreases or decreases picture contrast.
SharpnessSharpens or softens the picture. 
ColorIncreases or decreases color saturation.
TintIncreases or decreases the green tones.
Color Temp.Cool  Gives the white colors a bluish tint.
Warm Gives the white colors a reddish tint.
Normal Gives the white color a nature tint.
Noise ReductionReduces the noise level of connected equipment, and the VHF/UHF/CABLE input.
Gives four NR effect degrees, such as: Low, Mid, High and Off. The default setting is Mid.
Adaptive ContrastChoose On or Off to adjust the gamma after analyzing the input signal automatically.
DCRDynamic Contrast Ratio (DCR) auto adjusts the backlight of the screen.
BacklightBacklight strength adjustment, the tuning range is 0 ~ 30.
Aspect RatioChoose the display aspect.
PresetRestore the default video settings.
 
						

							27
Adjust Audio Setting 
OKMENU
/Exit
AUDIO
Sound Mode
Bass
Treble
Audio Source Balance32
32
0
SPDIF
Speaker
Move Select Return ExitPersonal
Stereo
PCM
On
1MU
/ ExitENPress MENU/EXIT to call out MENU.
2
Press ▲/▼ to select “Audio” , and press OK.
3
Press ▲/▼ to select Audio SettingsÖSound Mode, Bass, Treble, Balance, Audio Source, Audio Language, SPDIF, 
Speaker, Multi Language, AVL, Preset, and press OK to enter.
4
Press ◄/► to adjust.
5
MU
/ ExitENPress MENU/EXIT again to exit.
Audio Setting Items Description
Sound ModeMusic: Enhances treble and bass.
Speech: Enhances treble and keep bass in middle.
Personal: Adjust sound mode as personal favorite.
Sound Mode can also be accessed by pressing Audio on the remote control. 
Bass Increases or decreases lower-pitched sounds. 
Treble Increases or decreases higher-pitched sounds. 
Balance Emphasizes left or right speaker balance. 
Audio SourceSelect the audio source from Mono, Stereo, or SAP. (This function works in ATV only.)
Audio LanguageChange the audio language setting on ATSC TV programs. The number of the supported audio languages
(English / Français / Español)
SPDIFDigital audio output format. Select from RAW and PCM. The difference between SPDIF PCM or RAW:
SPDIF PCM: It will only output as a PCM 44.1Khz digital no matter what the recording is in the media.
SPDIF RAW: It will output the stream as it is digitally recorded, i.e. DTS recording as a DTS or a Dolby as a Dolby, or a 
native 48 or 96Khz.
SpeakerChoose to turn on / off the TV internal speaker. The digital audio output signals and earphone output signals will not be 
turned off even though the TV speaker is off. The default setting is On.
Multi LanguageTo choose the multi-language in DTV.
AVLEnable or disable Automatic Volume Level. 
PresetRestore the default audio settings.
 
						

							28
Adjust PC Setting
This setting is only available in PC mode.
OKMENU
/Exit
VGA
Move Select Return ExitV-Position
Clock
Auto AdjustPhase
Preset H-Position
13 17
8
2
1MU
/ ExitENPress MENU/EXIT to call out MENU.
2
Press ▲/▼ to select “PC” , and press OK.
3
Press ▲/▼ to select PC Settings: H. Position, V. Position, Clock, Phase, Auto Adjust, Preset, and press OK to 
enter.
4
Press ◄/► to adjust.
5
MU
/ ExitENPress MENU/EXIT again to exit.
PC Setting Description
H. PositionAdjusts the Horizontal positioning.
V. PositionAdjusts the Vertical positioning.
ClockAdjusts the Clock frequency on VGA signal.
PhaseAdjusts the Phase frequency on VGA signal.
Auto AdjustAuto sync. PC timing to fit full screen display. 
For detail supported timing, please refer PC Input Signal Reference Chart on page 15.
PresetRestore the default PC settings.
 
						

							29
Feature Setup
OKMENU
/Exit
FEATURE
Move Select Return Exit
Time
Password Setting
Closed Captions Parental Control
Analog Captions
Digital Captions
SERVICE1CC1Off
Menu LanguageEnglish
1MU
/ ExitENPress MENU/EXIT to call out MENU.
2
Press ▲/▼ to select “Setup” , and press OK.
3
Press ▲/▼ to select Setting items: Menu language, Time, Password Setting, Parental Control, Closed Captions, 
Analog Caption, etc. and press OK to enter.
4
Press ◄/► to adjust.
5
MU
/ ExitENPress MENU/EXIT again to exit.
The submenu of FEATURE mode in TV mode shows as below.
Menu Language: Adjust the language setting for this TV unit. (English / Français / Español) 1. 
1Press ◄/► to select: English / Français / Español, and press OK.
Time:  2. 
Set current time. The sub-menu includes Time Mode, Time Zone, and Daylight Savings.
 
FEATURE Time
Time Mode
Time Zone
Daylight Savings
Month
Day
Time YearAuto
HST
On
2010
Jan
1
12:02 AM
Move Select
OKMENU
/ExitReturn Exit
1Scroll to Time and press OK to enter the menu for Time adjustment.