Apple imac 20 inch mid 2009 User Manual
Have a look at the manual Apple imac 20 inch mid 2009 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 195 Apple manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
iMac (20-inch, Early/Mid 2009) Take Apart — Hard Drive 131 2010-11-24 5 Slide 2 pins on the side of hard drive out of 2 rubber grommets in chassis, and remove hard drive assembly from computer. 6 If installing a new hard drive, transfer the following to the replacement drive: • temp sensor cable • (2) T10 screws 922-8580 • (2) T10 pins 922-7001 The screw pins go on the side closest to the power & data cable connectors.
iMac (20-inch, Early/Mid 2009) Take Apart — Hard Drive Sensor Cable 132 2010-11-24 First Steps Remove: • Access Door • Glass Panel • Front Bezel • LCD Panel Tools • ESD wrist strap Hard Drive Sensor Cable
iMac (20-inch, Early/Mid 2009) Take Apart — Hard Drive Sensor Cable 133 2010-11-24 Removal 1 Disconnect temp sensor cable from its connector on top of logic board. 2 Peel back foam gasket on top of hard drive and disconnect sensor cable from retaining clip (922- 8183). Note: Image at right shows a map of connectors on top of logic board. Hard drive sensor cable connects to the furthest left of the 3 connectors. Hard drive sensor has a 3-pin connector. Optical drive sensor has a 2-pin connector. Hard drive fan has a 4-pin connector.
iMac (20-inch, Early/Mid 2009) Take Apart — Optical Drive 134 2010-11-24 First Steps Remove: • Access Door • Glass Panel • Front Bezel • LCD Panel Important: When servicing optical drive, handle it by edges only. Pressing elsewhere on drive could damage internal mechanism. Tools • ESD wrist strap • Torx T10 screwdriver • Black stick Optical Drive
iMac (20-inch, Early/Mid 2009) Take Apart — Optical Drive 135 2010-11-24 Removal 1 Remove T10 machine screws: (2) 922-6842 2 Carefully peel back strip of EMI mesh tape from rear housing. Reassembly Notes: Make sure EMI mesh does not cover any of the slot-load opening on rear housing. Also, make sure 4 inverter cables do not get trapped under optical drive. 3 Wiggle optical drive data cable connector away from optical drive. A black stick may be helpful.
iMac (20-inch, Early/Mid 2009) Take Apart — Optical Drive 136 2010-11-24 4 Disconnect temp sensor cable from connector on top edge of logic board. 5 Lift optical drive out of rear housing. Warning: Handle optical drive by the edges only! Pressing or squeezing elsewhere could damage its internal mechanism. Replacement Note: If installing a new optical drive, peel back foam gasket and disconnect temp sensor cable from retaining clip on reverse side of drive. Transfer the following to the replacement drive: • temp sensor cable • EMI mesh tape
iMac (20-inch, Early/Mid 2009) Take Apart — Optical Drive Sensor Cable 137 2010-11-24 First Steps Remove: • Access Door • Glass Panel • Front Bezel • LCD Panel • Optical Drive Tools • ESD wrist strap Optical Drive Sensor Cable
iMac (20-inch, Early/Mid 2009) Take Apart — Optical Drive Sensor Cable 138 2010-11-24 Removal 1 On reverse side of optical drive, peel back foam gasket and remove temp sensor cable (922-8827) from retaining clip (922- 8183). Note: Image at right shows a map of connectors on top of logic board. Optical drive sensor cable connects to the middle one of the 3 connectors. Hard drive sensor has a 3-pin connector. Optical drive sensor has a 2-pin connector. Hard drive fan has a 4-pin connector.
iMac (20-inch, Early/Mid 2009) Take Apart — Optical Drive Fan 139 2010-11-24 First Steps Remove: • Access Door • Glass Panel • Front Bezel • LCD Panel Tools • ESD wrist strap Optical Drive Fan
iMac (20-inch, Early/Mid 2009) Take Apart — Optical Drive Fan 140 2010-11-24 Removal 1 Disconnect cable from logic board. 2 Lift fan off 3 guide posts in the rear housing.