Belkin Router F5D8231-4 User Manual

Product  Overview
Integrated N1 Wireless Access Point 
N1  MIMO  is  an  exciting  new  wireless  technology  based  on  the  draft 
IEEE  802.11n  specification.  It  employs  MIMO  (Multiple  Input  Multiple 
Output)  smart-antenna  technology  that  achieves  data  rates  of  up  to 
300Mbps.*  Actual  throughput  is  typically  lower  than  the  connected 
data  rate  and  will  vary  depending  on  your  networking  environment.
* NOTE :  The  standard  transmission  rate—300Mbps—is  the  physical...

Package Contents
•  Belkin  N1  Wireless  Router
•  Quick  Installation  Guide
•  Belkin  Setup  Assistant  Software  CD
•  RJ45  Ethernet  Networking  Cable
•  Power  Supply
•  User  Manual
•  Network  Status  Display  Guide
•  Wireless  Security  Setup  Guide
System Requirements
•  Broadband  Internet  connection  such  as  a  cable  or  DSL  modem with  RJ45  (Ethernet)  connection
•  At  least  one  computer  with  an  installed  network  interface  adapter
•  TCP/IP  networking  protocol  installed...

1211
Knowing  your  Router

1211
Knowing  your  Router

The  Router  has  been  designed  to  be  placed  on  a  desktop.  All  of  the 
cables  exit  from  the  rear  of  the  Router  for  better  organization  and 
utility.  The  Network  Status  Display  is  easily  visible  on  the  FRONT
of  the  Router  to  provide  you  with  information  about  network  activity 
and  status.  See  the  Network  Status  Display  Guide  for  more
detailed  information
A.   Wireless Security  
OFFWireless...

12

Knowing  your  Router
12
s e c t i o n2
1
3
4
5
6
7
8
9
10

D.  Router/Power Status    
When you apply power to the Router or restart it, a short period of 
time elapses while the Router boots up. During this time, the “router” 
icon blinks. When the Router has completely booted up, the “router” 
icon becomes a solid light, indicating the Router is ready for use.
 
OFF Router  is  off
Blinking  Blue Router  is  booting  up
Solid  Blue Router  is  on  and  ready
E.   Wireless Status   
OFF Wireless...

1413
Knowing  your  Router

1413
Knowing  your  Router

H.   Connections to Wired Computers               - 
GrayConnect  your 
wired  (non-wireless)  computers  to  these  ports.  These  ports  are 
RJ45,  10/100  auto-negotiation,  auto-uplinking  ports  for  standard 
UTP  category  5  or  6  Ethernet  cable.  The  ports  are  labeled  1 
through  4,  with  onboard  LEDs  on  the  connectors.
I.   Connection to Modem              - YellowThis  port  is  for  connection  to  your  cable  or  DSL...

14

Knowing  your  Router
14
s e c t i o n2
1
3
4
5
6
7
8
9
10

J.   Reset Button 
The  “Reset”  button  is  used  in  rare  cases  when  the  Router  may 
function  improperly.  Resetting  the  Router  will  restore  the  Router’s 
normal  operation  while  maintaining  the  programmed  settings.  You 
can  also  restore  the  factory  default  settings  by  using  the  “Reset” 
button.  Use  the  restore  option  in  instances  where  you  may  have 
forgotten  your  custom  password.
  i....

1615
Connecting  and  Configuring  your  Router

1615
Connecting  and  Configuring  your  Router

Verify the contents of your box. You should have the following:
•  Belkin  N1  Wireless  Router 
•  RJ45  Ethernet  Networking  Cable 
•  Power  Supply
•  Belkin  Setup  Assistant  Software  CD
•  User  Manual
•  Network  Status  Display  Guide
Modem Requirements 
Your  cable  or  DSL  modem  must  be  equipped  with  an  RJ45  Ethernet 
port.  Many  modems  have  both  an  RJ45  Ethernet  port  and  a  USB...

16

Connecting  and  Configuring  your  Router
16
s e c t i o n
2
1
3
4
5
6
7
8
9
10

Step 1     Hardware Connections – Follow the Quick Installation  Guide (QIG)
A. 
Unplug  your  modem’s  power 
cord.  Put  the  Router  next  to 
the  modem.  Raise  the  Router’s 
antennas.
B.  Locate  the  networking  cable 
that  connects  your  modem  and 
computer.  Unplug  that  cable  from 
your  modem,  and  plug  it  into
 
any  gray  port  on  the  back  of 
the  Router.
C. Find  your  new  networking  cable...

1817
Connecting  and  Configuring  your  Router

1817
Connecting  and  Configuring  your  Router

Step 2    Set Up the Router – Run the Setup Assistant SoftwareA. 
Shut  down  any  programs  that 
are  running  on  your  computer 
at  this  time.
  Turn  off  any  firewall  or
 
Internet-connection-sharing 
software  on  your  computer.
B.  Insert  the  CD  into  your  computer. 
The  Setup  Assistant  will 
automatically  appear  on  your 
computer’s  screen  within  15 
seconds.  Click  on  “Go”  to...

18

Connecting  and  Configuring  your  Router
18
s e c t i o n
2
1
3
4
5
6
7
8
9
10

Confirmation  Screen 
Verify  that  you  have  completed  all  QIG 
steps  by  checking  the  box  to  the  right 
of  the  arrow.  Click  “Next”  to  continue.
Progress  Screen
 
Setup  Assistant  will  show  you  a 
progress  screen  each  time  a  step  in 
the  setup  has  been  completed.
1.1      Checking  Settings 
The  Setup  Assistant  will  now 
examine  your  computer’s  network 
settings  and  gather...