ProForm 510 E Manual

USER%S MANUAL
Serial Number Decal
    CAUTION
Read all precautions and instruc-
tions in this manual before using 
this equipment. Keep this manual 
for future reference.
Model No. PFEL05811.0
Serial No.                                  
Write the serial number in the space 
above for reference.
QUESTIONS?
If you have questions, or if parts 
are damaged or missing, DO NOT 
CONTACT THE STORE; please 
contact Customer Care.
IMPORTANT: Please register this 
product (see the limited warranty 
on the back...

2
TABLE OF CONTENTS
WARNING DECAL PLACEMENT
This drawing shows the location(s) of the 
warning decal(s). If a decal is missing 
or illegible, see the front cover of this 
manual and request a free replacement 
decal. Apply the decal in the location 
shown. Note: The decal(s) may not be 
shown at actual size.
PROFORM is a registered trademark of ICON IP, Inc.
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

3
    WARNING: To reduce the risk of serious injury, read all important precautions and 
instructions in this manual and all warnings on your elliptical before using your elliptical. ICON 
assumes no responsibility for personal injury or property damage sustained by or through the use of 
this product.
1.  Before beginning any exercise program, 
consult your physician. This is especially 
important for persons over age 35 or per-
sons with pre-existing health problems.
2.  Use the elliptical only as...

4
 Thank you for selecting the revolutionary PROFORM® 
510 E elliptical. The 510 E elliptical provides an 
impressive selection of features designed to make your 
workouts at home more effective and enjoyable.
For your benefit, read this manual carefully before 
you use the elliptical. If you have questions after 
reading this manual, please see the front cover of this 
manual. To help us assist you, note the product model 
number and serial number before contacting us. The 
model number and the location...

5
 PART IDENTIFICATION CHART
Use the drawings below to identify the small parts needed for assembly. The number in parentheses below each 
drawing is the key number of the part, from the PART LIST near the end of this manual. The number following the 
key number is the quantity needed for assembly. Note: If a part is not in the hardware kit, check to see if it 
has been preassembled. Extra parts may be included.
M8 x 13mm Button Screw (82)58
M10 x 25mm Button Screw (131)54
M10 x 122mm Button Screw...

6
1.  With the help of a second person, place some of 
the packing materials (not shown) under the rear 
of the Frame (1). Have the second person hold 
the Frame to prevent it from tipping while you 
complete this step.
  Attach the Rear Stabilizer (2) to the Frame (1) 
with two M10 x 122mm Button Screws (104) and 
two M10 Split Washers (105).
  Remove the packing materials from under the 
rear of the Frame (1).
1
2
12
2
106
15
104105
a  To hire an authorized service technician to 
assemble this product,...

7
3
4
3.  With the help of a second person, place some 
of the packing materials (not shown) under the 
front of the Frame (1). Have the second per-
son hold the Frame to prevent it from tipping 
while you complete this step.
  Attach the Front Stabilizer (6) to the Frame (1)
with two M10 x 122mm Button Screws (104) and 
two M10 Split Washers (105).
  Remove the packing materials from under the 
front of the Frame (1).
1
6104105
4.  Orient the Upright (4) as shown. Have a second 
person hold the Upright...

8
6
55. Tip: Avoid pinching the Upper Wire (110). 
Avoid damaging the indicated plastic tabs. 
Set the Upright (4) on the Frame (1). 
  Attach the Upright (4) with four M10 x 25mm 
Button Screws (131) and four M10 Split Washers 
(105).
4
105
105
131
131
110
6.  Using a plastic bag to keep your fingers clean, 
apply some of the included grease to the Pivot 
Axle (35) and to two 16mm Wave Washers (54).
  Insert the Pivot Axle (35) through the Upright (4) 
and center it. Tip: It may be helpful to use a...

9
8
77.  Identify the Right Upper Body Arm (61), which 
is marked with a cRightd sticker, and orient it as 
shown.
  Slide the Right Upper Body Arm (61) onto the 
Right Upper Body Leg (60). 
  Attach the Right Upper Body Arm (61) with 
two M8 x 38mm Button Bolts (96) and two M8 
Locknuts (102). Make sure that the Locknuts 
are in the hexagonal holes. 
  Repeat this step for the Left Upper Body Arm 
(47).
Hexagonal 
Holes
60
61
7
4
47
63
110
96
8.  Untie and discard the wire tie on the Upper Wire 
(110)....

10
10
9
Avoid pinching 
the wires
7
9.  Tip: Avoid pinching the wires. Attach the 
Console (7) to the Upright (4) with four M4 x 
16mm Screws (101).
101
49
44
49
58
103
103
101
4
10. Identify the Right Pedal Arm (58), which is 
marked with a cRightd sticker, and orient it as 
shown.
  Attach a Pedal (49) to the Right Pedal Arm (58) 
with four M6 x 12mm Button Screws (103).
  Repeat this step for the Left Pedal Arm (44) 
and the other Pedal (49).