Addonics Technologies 19 Hard driveSSD Duplicators HD9SITDRHS User Manual

Technical Support
If you need any assistance to get your unit functioning properly, please have your 
product information ready and contact Addonics Technical Support at:
Hours: 8:30 am - 6:00 pm PST
Phone: 408-453-6212
Email: http://www.addonics.com/support/query/
v3.1.11
www.addonics.com
User Guide
1:9 HS HDD Duplicator Pro
(HD9SITDRHS)
T E C H N O L O G I E S         

www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
 
 
 
Drive InstallationGuide
Step 1
Use a Philips screwdriver to 
turn the cover securing screw 
clockwise into the OPEN 
position.
Step 2
Slide the aluminum cover towards 
the back end of the Diamond 
enclosure and remove it. 
Step 3
For SATA Drive:
Carefully place the SATA hard 
drive with the label facing up into 
the Diamond Enclosure. Push 
the hard drive towards the back 
end...

www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
 
 
For IDE Drive
Note: Configure your IDE hard 
drive as Master device
Connect the 4-Pin Molex cable to 
the power connector on the IDE 
hard drive. Carefully place the IDE 
hard drive with the label facing up 
into the Diamond enclosure. Push 
the hard drive toward the back 
end to secure the drive connectors 
onto the Diamond enclosure’s IDE 
connector.
Step 4
Turn the Diamond...

www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
 
Connecting  th e Power  Cable a nd Powering On
a .Connect the  power cord provided f rom the wall  outlet to  the  back  of the t ower. 
b. Turn on the main power switch on the rear of the chassis.
c. Push the power button on the front of the unit to turn on the HDD dup\
licator.
T here  are four buttons  and an LCD  on the panel  of HDD  Duplic ato r.
1  –  LCD s hows a funct ion...

www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
Main Menu
1. Copy HDD
Scans the ports, then copies from the source to any targets found.
2. Async Copy HDD
Scans the ports, then copies from the source to any targets found. More \
drives may be added before the process is complete, they will begin the \
process as soon as they are detected.
3. Compare HDD
Scans the ports, then any targets found will be compared to the source.
4....

www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
5. PreScan Source
Reads all blocks on the source drive to confirm no I/O errors are encoun\
-
tered.
6. ReScan BUS
Manually scans all ports and reports how many units were found.
7. Source Size
Examines the source drive and reports total space and space used, if 
drive contains compatible partitions. Press up/down to change display, 
ESC to exit.
8. Secure Erase
Scans all ports, then...

www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
Setup options
10-1. Language
Use this option to select the language of the system, currently only Eng\
-
lish is supported.
10-2. Copy Size
Controls how much of the source drive to use for copy operations, in 
percentage. Default setting is ALL (100%).
10-3. Startup Menu
Sets the first menu option to appear after boot. Default setting is Copy\
 
HDD.
10-4. Auto Compare
Controls...

www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
10-9. Auto Start Drive
When source drive is present, inserting a target drive will cause copy 
process to begin automatically. Default setting is OFF.
10-10. Auto Start Timer
Sets delay in time after target insertion before beginning auto copy 
process if Auto Start Drive is ON. Default setting is OFF (no delay).
10-11. Tolerance Size
Sets the minimum target size in percentage...

www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
12-03. Compare Firmware
Used to confirm correct firmware. Connect a drive formatted as FAT 
containing one partition with the firmware file in the root directory.
NOTE: This function scans the entire disk before proceeding. Providing 
a drive that is as small as possible is strongly recommended.
12-04. Quick Erase HDD
Scans the ports, then quickly erases all sectors on all connected...

www.addonics.com
Phone:   408-573-8580
Fax:     408-573-8588
Email:   http://www.addonics.com/sales/query/
CONTACT US