ADDONICS TECHNOLOGIES
Model: ADSAUSPCB
Hardware Installation:
Step 1. Connect the 2-pin power cable to the 2-pin power connector on the adapter. Be sure
to connect the red wire to the pin with +5V label.
Step 2. Connect a SATA cable to the SATA connector on the adapter and the other
end to the SATA device.
Step 3. Connect a USIB cable to the USIB connector on the adapter and the other
end to the host
TECHNICAL SUPPORT Email:...
Addonics Installation Guide
Model: AD4SAML and AD4SAML-PCI
AD4SAMLAD4SAML-PCI
(Multilane bridge for SATA storage)(Multilane bridge for SATA controller)
Please note that the boot drive, the drive that the OS will be installed on, must be connected to Port 1whenusing with any Addonics
SATA host controller ( the lowest port on the PCI bracket). Controllers from other manufacturer may have a different requirement.
Contact Information
Addonics Technologies
2466 Kruse Drive
San Jose CA, 95131...
T E C H N O L O G I E S
User Guide
Embedded USB Type-A Adapter(AD5PUSBA)
Technical Support
If you need any assistance to get your unit functioning properly, please have your
product information ready and contact Addonics Technical Support at:
Hours: 8:30 am - 6:00 pm PST
Phone: 408-453-6212
Email: http://www.addonics.com/support/query/
v7.1.11
www.addonics.com
ADDONICS TECHNOLOGIES
Model: ADAEC7722
Installation Guide
Hardware Installation:
Step 1: Plug in the Embedded IDE- Dual SATA Port Converter on the IDE
controller on the motherboard.
Step 2: Using a 4-pin floppy power cable from the power supply, connect it to the
4-pin floppy power connector on the Embedded IDE- Dual SATA Port Converter.
This will provide power to the converter.
Step 3: Connect a SATA drive to the SATA port 1 of the converter. This drive will
show up as a master device in the motherboard BIOS.
Step 4: Connect a second SATA drive to the...
ADDONICS TECHNOLOGIES
Model: ADIDESA
Installation Guide
Front View
Back View
Note: It is required to set up the IDE hard drive you are
connecting to the converter as a MASTER device.
1. Locate the 40-pin IDE connector of your IDE drive.
2. Connect the converter board to the IDE connector of the
hard drive.
3. Using the provided Y-power cable, connect the 4-pin
Molex connector to...
T E C H N O L O G I E S
User Guide
SATA - IDE Converter
(ADSAIDE)
Technical Support
If you need any assistance to get your unit functioning properly, please have your
product information ready and contact Addonics Technical Support at:
Hours: 8:30 am - 6:00 pm PST
Phone: 408-453-6212
Email: http://www.addonics.com/support/query/
v4.1.11
Master, Slave & Cable
Select JumpersSATA Power and Data Connector 40-Pin IDE Connector
Pin 1 Marker 4-Pin Floppy Power Connector
Front View
Back View Jumper Settings...
Technical Support
If you need any assistance to get your unit functioning properly, please
have your product information ready and contact Addonics Technical
Support at:
Hours: 8:30 am - 6:00 pm PST
Phone: 408-453-6212
Email: http://www.addonics.com/support/query/
T E C H N O L O G I E S
www.addonics.com
SATA to 44-Pin IDE Conver ter
(ADSAIDE44)
User Guide
Note: Before installing the ADSALVD160, you need to set up the SCSI host adapter
first. Once the SCSI host adapter had been configured and detected by the system,
you can now follow the instructions below.
Your SCSI host adapter must be terminated.
1. Connect one end of the SCSI cable that is connected to the SCSI host adapter to
the 68-pin female SCSI connector of the ADSALVD160.
2. Connect the SATA hard drive to the SATA interface on the ADSALVD160.
3. Using the provided Y-power cable, connect...
ADDONICS TECHNOLOGIES
ADSATAPIU2 (slim ATAPI to USB 2.0 Converter)
SPECIFICATIONS
Specifications:
· USB 2.0 interface for up to 480 Mbits/sec data
transfer
· Supports slim ATAPI optical drives
· USB 5-pin header for internal connection
· Works undWindows 98SE, Me, 2000 and XP,
Vista, Mac OS X, Linux
· Dimension (W x D x H) –
78 mm x 36 mm x 5 mm
Features:
· Convert any slim drive ATAPI/IDE interface
to internal 5-pin header USB 2.0
· High tran sfer rate of 480Mbps
·...
ADDONICS TECHNOLOGIES
Model: ADSSSAI44
Installation Guide
Front View
Jumper Settings
Master Slave Cable Select
Note: To set the slim ATAPI SATA drive as a Master
Device when connected to an IDE channel, you
need to short the top pins located on the converter
by placing a jumper. As a Slave Device short the
middle pins.
1. Locate the slim SATA ATAPI connector of...
Technical Support
If you need any assistance to get your unit functioning properly, please have your
product information ready and contact Addonics Technical Support at:
Hours: 8:30 am - 6:00 pm PST
Phone: 408-453-6212
Email: http://www.addonics.com/support/query/
v7.1.11
www.addonics.com
T E C H N O L O G I E S
User Guide
Slim ATAPI SATA to USB 2.0/1.1 Converter (ADSSSAU2)
Installation:
1. Mount the Hybrid Port converter on a 3.5” drive bay.
2. To provide power, connect a 4-pin floppy power cable from the power
supply to the 4-pin floppy power connector on the converter.
3. Using a SATA data cable, connect one end to an onboard or add-in SATA
controller card to the SATA port of the Hybrid Port converter.
Note: For the Hybrid Port converter to support hot swapping, it needs to be
connected to an onboard or add-in SATA controller card that supports hot...
