Home > Corbin

Corbin User Manuals

The manuals from this brand are divided to the category below. You can easily find what you need in a few seconds.
Show categories
Corbin User Manuals
                                                    How to Swage Bullets Using The  FJFB-3-H Die Set
1 2
3
4
6
57Type -H dies fit into the ram of the Corbin Mega-Mite manual (CSP-2), the Hydro, Jr. (CSP-2H) press,
and the Corbin Hydro-Press (CHP-1). The 3-die set consists of a CORE SWAGE (CSW--1-H), a CORE
SEAT(CS-1-H), and a POINT FORM (PF-1-H) die, each with one internal and one external punch.
The external punch (1) is held in the floating punch holder (2), which comes with the press. A threaded
bushing (3) is removed from the bottom of the punch...
                                            
                                                    How to Swage Bullets Using The  FJFB-3-H Die Set
1 2
3
4
6
57Type -H dies fit into the ram of the Corbin Mega-Mite manual (CSP-2), the Hydro, Jr. (CSP-2H) press,
and the Corbin Hydro-Press (CHP-1). The 3-die set consists of a CORE SWAGE (CSW--1-H), a CORE
SEAT(CS-1-H), and a POINT FORM (PF-1-H) die, each with one internal and one external punch.
The external punch (1) is held in the floating punch holder (2), which comes with the press. A threaded
bushing (3) is removed from the bottom of the punch...
                                            
                                                    Finned Shotgun Slug Swage KitThe finned hollow cavity shotgun slug is
formed in three steps, using a CSW-1-H
core swage, CS-1-H core seater, and
PF-1-H point form die. An ejector frame is used,
with special ejecting external punch and punch holder,
to free the finned slug from the final punch. The usual
FPH-1-H floating punch holder is NOT used in the final
operation of forming the point. It can be used in the first two
steps.
The 12-gauge set is designed to make slugs from 1.125 to
1.375 ounces. Heavier...
                                            
                                                    Finned Shotgun Slug Swage KitThe finned hollow cavity shotgun slug is
formed in three steps, using a CSW-1-H
core swage, CS-1-H core seater, and
PF-1-H point form die. An ejector frame is used,
with special ejecting external punch and punch holder,
to free the finned slug from the final punch. The usual
FPH-1-H floating punch holder is NOT used in the final
operation of forming the point. It can be used in the first two
steps.
The 12-gauge set is designed to make slugs from 1.125 to
1.375 ounces. Heavier...
                                            
                                                    How to Swage Bullets Using The
  FJFB-3-S or -M Die Set
Type -S dies are 1-inch in diameter, with a 5/8-24 shank, and fit into the ram of  the Corbin
CSP-1 All-Steel press. The type -M dies are 3/4-inch in diameter, with a 5/8-24 shank, and fit
into the ram of the CSP-1 or the CSP-3 Silver Press (horizontal). The 3-die set consists of a
CORE SWAGE (CSW-1), a CORE SEAT(CS-1), and a POINT FORM (PF-1) die, each with one
internal and one external punch.
The external punch is held in the floating punch...
                                            
                                                    How to Swage Bullets Using The
  FJFB-3-S or -M Die Set
Type -S dies are 1-inch in diameter, with a 5/8-24 shank, and fit into the ram of  the Corbin
CSP-1 All-Steel press. The type -M dies are 3/4-inch in diameter, with a 5/8-24 shank, and fit
into the ram of the CSP-1 or the CSP-3 Silver Press (horizontal). The 3-die set consists of a
CORE SWAGE (CSW-1), a CORE SEAT(CS-1), and a POINT FORM (PF-1) die, each with one
internal and one external punch.
The external punch is held in the floating punch...
                                            
                                                    FPH-1-H    FPH-1-H   Floating Punch Holder Floating Punch HolderThe Corbin Floating Punch Holder is used to support and adjust the EXTER-
NAL punches for Corbin type -H die sets, in the CSP-2 Mega Mite, CSP-2H
Hydro Jr., and CHP-1 Hydro-Press swaging presses.
The holder has a 1.5-inch by 12 turn/in thread. Each turn of the punch
holder changes the insertion depth of the punch, and the length of core
(in a core swage die) by exactly 1/12 of an inch (.0833). A quarter turn
adjusts the punch depth by...
                                            
                                                    FPH-1-H    FPH-1-H   Floating Punch Holder Floating Punch HolderThe Corbin Floating Punch Holder is used to support and adjust the EXTER-
NAL punches for Corbin type -H die sets, in the CSP-2 Mega Mite, CSP-2H
Hydro Jr., and CHP-1 Hydro-Press swaging presses.
The holder has a 1.5-inch by 12 turn/in thread. Each turn of the punch
holder changes the insertion depth of the punch, and the length of core
(in a core swage die) by exactly 1/12 of an inch (.0833). A quarter turn
adjusts the punch depth by...
                                            
                                                    FPH-2-H
Positive Stop Punch Holder
The Corbin Positive Stop Punch Holder is used to stall the
Hydro-press ram against the die face, bringing the ram to a
positive stop, and using the PRESSURE REVERSE controls to
stop, hold, and
reverse the ram
travel. Punches
are dropped into
the holder from
the top, by first
removing the
threaded rod.
The depth of
punch inser tion
into the die is
controlled by the
position of the
threaded rod.
The punch can
slide back until it contacts the end of  the rod, at which...
                                            
                                                    FPH-2-H
Positive Stop Punch Holder
The Corbin Positive Stop Punch Holder is used to stall the
Hydro-press ram against the die face, bringing the ram to a
positive stop, and using the PRESSURE REVERSE controls to
stop, hold, and
reverse the ram
travel. Punches
are dropped into
the holder from
the top, by first
removing the
threaded rod.
The depth of
punch inser tion
into the die is
controlled by the
position of the
threaded rod.
The punch can
slide back until it contacts the end of  the rod, at which...
                                            
                                                    How to Swage Bullets Using The
FRBL-6-M, -S, or -H Die Set
Type -H dies fit into the ram of  the Corbin Mega-Mite press (CSP-2), Corbin
Hydro, Jr., (CSP-2H) press, and the Corbin Hydro-Press (CHP-1). The type -M
dies fit either the horizontal Silver Press (CSP-3) or the vertical Series II Press
(CSP-1). The type -S dies fit only the Series II Press (CSP-1). The last letter, -
M, -S, or -H, describes the outside diameter, threads, punch lengths, and which
presses the die set will fit. If a tool fits both...
                                            
                                                    How to Swage Bullets Using The
FRBL-6-M, -S, or -H Die Set
Type -H dies fit into the ram of  the Corbin Mega-Mite press (CSP-2), Corbin
Hydro, Jr., (CSP-2H) press, and the Corbin Hydro-Press (CHP-1). The type -M
dies fit either the horizontal Silver Press (CSP-3) or the vertical Series II Press
(CSP-1). The type -S dies fit only the Series II Press (CSP-1). The last letter, -
M, -S, or -H, describes the outside diameter, threads, punch lengths, and which
presses the die set will fit. If a tool fits both...
                                            
                                                    How to Swage Bullets Using The
FRBO-5-M, -S, or -H Die Set
Type -H dies fit into the ram of  the Corbin Mega-Mite press (CSP-2), Corbin
Hydro, Jr., (CSP-2H) press, and the Corbin Hydro-Press (CHP-1). The type -M
dies fit either the horizontal Silver Press (CSP-3) or the vertical Series II Press
(CSP-1). The type -S dies fit only the Series II Press (CSP-1). The last letter, -
M, -S, or -H, describes the outside diameter, threads, punch lengths, and which
presses the die set will fit. If a tool fits both...
                                            
                                                    How to Swage Bullets Using The
FRBO-5-M, -S, or -H Die Set
Type -H dies fit into the ram of  the Corbin Mega-Mite press (CSP-2), Corbin
Hydro, Jr., (CSP-2H) press, and the Corbin Hydro-Press (CHP-1). The type -M
dies fit either the horizontal Silver Press (CSP-3) or the vertical Series II Press
(CSP-1). The type -S dies fit only the Series II Press (CSP-1). The last letter, -
M, -S, or -H, describes the outside diameter, threads, punch lengths, and which
presses the die set will fit. If a tool fits both...
                                            
                                                    Hand Cannelure Tool
HCT-1
 The Corbin Hand Cannelure Tool creates cannelures
(serrated grooves) on lead or jacketed bullets from .224
to .458 caliber.  The tool has a positive stop for control
of the cannelure depth, but can also be operated by
feel with good results.  Position of the cannelure can
be set by a base-touching stop screw on the side of the
tool.
Mount the tool on your bench top, so that the crank handle is free to turn
over the edge of the bench.   Two mounting holes through the base allow...
                                            
                                                    Hand Cannelure Tool
HCT-1
 The Corbin Hand Cannelure Tool creates cannelures
(serrated grooves) on lead or jacketed bullets from .224
to .458 caliber.  The tool has a positive stop for control
of the cannelure depth, but can also be operated by
feel with good results.  Position of the cannelure can
be set by a base-touching stop screw on the side of the
tool.
Mount the tool on your bench top, so that the crank handle is free to turn
over the edge of the bench.   Two mounting holes through the base allow...