Home > Corbin > Firearms accessories

Corbin Firearms accessories User Manuals

The manuals from this brand are divided to the category below. You can easily find what you need in a few seconds.
Corbin Firearms accessories User Manuals
                                                    Rebated Boattail Die Set, RBT-2
The RBT-2 die set consists of
two dies and four punches.
The first die is used to hold
the f lat-based jacket while the
core is first seated. This forms
a boattail-shaped base on the
bullet caused by the lead
pressure pushing the jacket
into the shape of  the die.
The second die accepts this
boattailed jacket with its core
already seated, and forms the
rebate or shoulder on the base. The same external punch is used for both
dies, but each has its own  internal punch. The...
                                            
                                                    o BSD-224Ro BSD-243Ro BSD-251Ro BSD-308Ro BSD-312Ro BSD-314Ro BSD-355Ro BSD-257R2-Die Set for Reloading PressThe first die is the CORE
SEATER. It is used to expand
the jacket to proper diameter
while pressing (seating) the
lead filling (core) into the
jacket.
The INTERNAL punch stays
inside the die body and is used
to push the bullet out. A knock-
out rod slips into the top of the die.
Tapping the head of this rod pushes
the bullet out.
The EXTERNAL punch can be differ-
ent diameters and shapes on the...
                                            
                                                     BSK-1-S  Ball Swage Kit
Diameter ................... . ______ in
Core  Weight ............. . ______ gr
Final Ball Weight ...... . ______ gr
core swageball swage
1) Swage the cores to the indicated core weight, above, using the
core swage die. The lead cores can be cast, or cut from lead wire to
a weight that is from 3 to 5 grains more, and the surplus lead is bled
off  in the swaging operation
through bleed holes in the side of the die. The core
swage die fits into the press ram. A stop pin ejects the...
                                            
                                                    DDS-1
Dual Diameter Sizer Die
The DDS-1 Dual Diameter Sizer reduces the forward por-
tion of  a bullet so that it rides atop the rifling, while leav-
ing the base at full engagement diameter. It can also be
used, in a reversed nose/base punch design, for making
heel-type bullets.
The internal punch is machined to fit the nose of the
bullet. It can be changed to handle various shapes of bullets, in the
caliber of the die. The base or external punch is the same shape as
the bullet base (flat, cup, hollow,...
                                            
                                                     BSK-1-S  Ball Swage Kit
Diameter ................... . ______ in
Core  Weight ............. . ______ gr
Final Ball Weight ...... . ______ gr
core swageball swage
1) Swage the cores to the indicated core weight, above, using the
core swage die. The lead cores can be cast, or cut from lead wire to
a weight that is from 3 to 5 grains more, and the surplus lead is bled
off  in the swaging operation
through bleed holes in the side of the die. The core
swage die fits into the press ram. A stop pin ejects the...
                                            
                                                    DDS-1
Dual Diameter Sizer Die
The DDS-1 Dual Diameter Sizer reduces the forward por-
tion of  a bullet so that it rides atop the rifling, while leav-
ing the base at full engagement diameter. It can also be
used, in a reversed nose/base punch design, for making
heel-type bullets.
The internal punch is machined to fit the nose of the
bullet. It can be changed to handle various shapes of bullets, in the
caliber of the die. The base or external punch is the same shape as
the bullet base (flat, cup, hollow,...
                                            
                                                    BRD-1     -R
 -M
-H
Bullet Reducing Die
FROM  ____________  TO  ____________
The Corbin Bullet Reducing Die draws
down (reduces) the diameter of a bullet
by pushing it through a die and out the
top. The punch presses on the BASE of
the bullet, and should match the base di-
ameter and shape of the finished (drawn)
bullet. If a punch is used that is too small
or the wrong shape for the base, it will
deform the bullet resulting in poor accu-
racy.
Bullets can usually be reduced at least
0.005-in diameter,...
                                            
                                                        ET-1-H Jacket Trim Die
The Corbin ET-1-H Expand/Trim die fits the Corbin MegaMite, Hy-
dro Junior, or Hydro Press. It trims jackets of  a given caliber to precise,
shorter lengths with a clean, even beveled mouth in one stroke.
The ET-1-H is best used with the optional Corbin SK-1-H Stripper Kit,
which automatically strips the trimmed portion of  the jacket from the
punch, and ejects the jacket, on the down stroke of  the press. The Stripper
Kit is universal for all ET-1-H trimmer dies, with the...
                                            
                                                    BRD-1     -R
 -M
-H
Bullet Reducing Die
FROM  ____________  TO  ____________
The Corbin Bullet Reducing Die draws
down (reduces) the diameter of a bullet
by pushing it through a die and out the
top. The punch presses on the BASE of
the bullet, and should match the base di-
ameter and shape of the finished (drawn)
bullet. If a punch is used that is too small
or the wrong shape for the base, it will
deform the bullet resulting in poor accu-
racy.
Bullets can usually be reduced at least
0.005-in diameter,...
                                            
                                                        ET-1-H Jacket Trim Die
The Corbin ET-1-H Expand/Trim die fits the Corbin MegaMite, Hy-
dro Junior, or Hydro Press. It trims jackets of  a given caliber to precise,
shorter lengths with a clean, even beveled mouth in one stroke.
The ET-1-H is best used with the optional Corbin SK-1-H Stripper Kit,
which automatically strips the trimmed portion of  the jacket from the
punch, and ejects the jacket, on the down stroke of  the press. The Stripper
Kit is universal for all ET-1-H trimmer dies, with the...
                                            
                                                    Bullet Polisher Kit
               BPK-1
The Corbin BPK-1 Bullet Polisher Kit consists of  a thermally-protected
115 volt 60Hz vibrator motor with built-in power cord and switch, a mount-
ing bracket which circles the motor housing and secures the motor to the
bottom of  a gallon pail or a large coffee can, a pound of  walnut shell
grinding media, and four self-locking nuts and matching bolts and wash-
ers (to fasten the bracket to the bottom of  the container).
The motor should be mounted under the...
                                            
                                                    Bullet Polisher Kit
               BPK-1
The Corbin BPK-1 Bullet Polisher Kit consists of  a thermally-protected
115 volt 60Hz vibrator motor with built-in power cord and switch, a mount-
ing bracket which circles the motor housing and secures the motor to the
bottom of  a gallon pail or a large coffee can, a pound of  walnut shell
grinding media, and four self-locking nuts and matching bolts and wash-
ers (to fasten the bracket to the bottom of  the container).
The motor should be mounted under the...
                                            
                                                    ET-1-R   Jacket Trim Die
The ET-1-R jacket trim die fits a standard 7/8-14 reloading press with slotted ram (for
standard RCBS type button shell holders). You can use it to trim a given caliber of  bullet
jacket to shorter lengths. The length of the trimmed jacket is adjustable over a wide range
by turning the threaded stop in the top of the die.
A tapered, piloted punch slips into the reloading press ram slot, just like a shell holder.
Do not try to use a shell holder in addition! It will not fit the...
                                            
                                                    ET-1-R   Jacket Trim Die
The ET-1-R jacket trim die fits a standard 7/8-14 reloading press with slotted ram (for
standard RCBS type button shell holders). You can use it to trim a given caliber of  bullet
jacket to shorter lengths. The length of the trimmed jacket is adjustable over a wide range
by turning the threaded stop in the top of the die.
A tapered, piloted punch slips into the reloading press ram slot, just like a shell holder.
Do not try to use a shell holder in addition! It will not fit the...
                                            
                                                    The Corbin S-PRESS works with these dies:
RCorbin type -S Bullet Swage Dies (1-inch body, 5/8-24 shank). Die
fits the ram, punch used in floating punch holder. Self-ejection.
RCorbin type -M Bullet Swage Dies (7/8-inch body, 5/8-24 shank).
Die fits the ram, punch used in floating punch holder. Self-ejection.
RCorbin type -R Bullet Swage Dies (7/8-14 threads, button/T-slot
punch). Die fits press head, punch fits reloading adapter.
RCorbin type -R Draw Dies (7/8-14 threads, botton/T-slot punch).
Die fits...
                                            
                                                    The Corbin S-PRESS works with these dies:
RCorbin type -S Bullet Swage Dies (1-inch body, 5/8-24 shank). Die
fits the ram, punch used in floating punch holder. Self-ejection.
RCorbin type -M Bullet Swage Dies (7/8-inch body, 5/8-24 shank).
Die fits the ram, punch used in floating punch holder. Self-ejection.
RCorbin type -R Bullet Swage Dies (7/8-14 threads, button/T-slot
punch). Die fits press head, punch fits reloading adapter.
RCorbin type -R Draw Dies (7/8-14 threads, botton/T-slot punch).
Die fits...