3M Digital Media System 800 Operating Manual

Product Description
Machine Characteristics
The Digital Media System 800 integrates metal halide lamp and Digital Light Processor (DLP) technology. It 
accepts input from computer and/or video sources and projects a super bright image.
The Digital Media System 800 offers the following features:
1. One panel 0.7” DDR DMD projection system
2. Vikuiti
™ Super Close Projection(SCP) technology
3. VGA/SVGA/XGA/SXGA/MAC/(UXGA) PC compatibility
4. NTSC/PAL/SECAM/Composite/S-video/Component (YPbPr/YCbCr)/SDTV...

12
3M™ Digital Media System 800 Series
© 3M 2007. All Rights Reserved.
ENGLISH
Installation and System Setup
Installation & System Setup 
Setting Up the Projector
1.  Mount whiteboard/projection screen in desired 
location on wall if necessary. The top of the 
whiteboard/projecction screen should be at least 
86" (2.18 m) from the floor.
86"
(2.18 m)
to floor
Whiteboard/
Projection ScreenWhiteboard/
Projection Screen
2.  The Digital Media System 800 Series can 
project an image size between...

13 3M
™ Digital Media System 800 Series
© 3M 2007. All Rights Reserved.
ENGLISH
Installation and System Setup
5. Determine the appropriate anchor to use with 
your wall type. Install five anchors at the 
marked locations. Install, but do not tighten, five 
mounting screws.Masonry
Hollow Wall
Solid Wall/ Wall Stud
     
6. (Digital Media System 810 Only) Measure the 
thickness of the whiteboard/projection screen to 
determine the number of shims needed. 
Screen Thickness Number of Shims
0–1" (0–25 mm)...

14
3M™ Digital Media System 800 Series
© 3M 2007. All Rights Reserved.
ENGLISH
Installation and System Setup
10. Attach the safety cable securely to the wall with 
an appropriate anchor.
Note: Fully extend safety cable and then secure 
to wall. If necessary, use tie wraps to minimize 
cable slack.  
Attach safety cable securely to stud or solid wall.
Cable should have no slack.
11. Slide the contol panel cable tab into the slot at 
the bottom left of the unit.
Power Cable
Control Panel Cable
12. Connect...

15 3M
™ Digital Media System 800 Series
© 3M 2007. All Rights Reserved.
ENGLISH
Installation and System Setup
13. (Digital Media System 815 Only) Attach  the 
Annotation Pod as shown on pages 8–9 of the 
Digital Media System 815 eBeam
™ Software for 
Interactive Whiteboard Operator’s Guide.
14. Start up the projector by switching on the main 
power switch, then pressing the power button on 
the projector, the control panel or the remote.
Main Power Switch Power Button
15. Adjust the projector arm length...

16
3M™ Digital Media System 800 Series
© 3M 2007. All Rights Reserved.
ENGLISH
Remote Control Unit
Projector Remote Control
Remote Control Functions
Aim the remote control toward the projection screen or at the sensor. Press desired remote button to send a signal 
to the projector.
Power
Pointer
Input
Magnify
Menu
Freeze
PIPEnter
Blank
PIP
INPTimer
PIP
SWAP
100%
Power:Power ON/OFF Projector
Pointer: 
Move (point) the cursor on the projected image. 
Navigate menus. 
Mouse L-Click
Mouse R-Click
Enter:Enter...

17 3M
™ Digital Media System 800 Series
© 3M 2007. All Rights Reserved.
ENGLISH
Basic Operations
Basic Operations
Projector Start Up
Read the Safety Information before operating the Digital Media System 800. After all cable connections have 
been completed, the projector can be powered up. 
1. Turn off all power to the projector and input sources during cable hook up.
2. Connect cables being careful not to bend any pins in the cable plug or input terminal. 
3. Press the Main Power switch on the control...

18
3M™ Digital Media System 800 Series
© 3M 2007. All Rights Reserved.
ENGLISH
Basic Operations
Image Adjustment
1. Set optical engine (head) adjustment screws to nominal height.
2. Set arm mount adjustment screws to nominal height.
3. Set base skew adjustment screw to nominal height.
4. Adjust image size to 60” +/- 0.5”.
5. Adjust head adjustment screws to position image on target.
- Top center of image on target top center.
- Top line of image skew to within skew specification.
6. Adjust base only if...

19 3M
™ Digital Media System 800 Series
© 3M 2007. All Rights Reserved.
ENGLISH
Basic Operations
Picture sub menu
Action Description
Picture
ModePicture modes are provided so the user can 
simply optimize the projector image set-up to 
suit his/her program type:
1) TV
2) Business
3) Cinema
4) SportsThe Color, adjustment values will change, but 
the user will adjust the Color settings relative 
to the Picture Modes.  
Picture Mode Options
1) Color Temperature
2) Gamma Table
3) Brightness
4) Contrast
5)...

20
3M™ Digital Media System 800 Series
© 3M 2007. All Rights Reserved.
ENGLISH
Basic Operations
Noise
ReductionAdjusts the amount of noise reduction to be applied to the image. There are 4 settings: 
1) Off 
2) Low
3) Medium
4) High
Aspect
RatioThere are 4 Aspect Ratio settings:
1) Full Screen
2) Standard
3) Letter Box
4) Theatre-Wide(16:9)
More… Allows the user to navigate into the advanced picture settings menu.
Reset Resets values in this sub-menu only.
Table 1:Picture Sub Menu Function description