3M Super Close Projection System SCP716 Operators Guide

							21 Operator’s Guide 3M
™ Super Close Projection System SCP716
© 3M 2009. All Rights Reserved.
ENGLISH
Operating Instructions
Projector Start Up
Read the Important Safeguards before operating the SCP716. After all cable connections have been completed, 
refer to Setup and Configuration, the projector can be powered up.
For best results, please observe the following start up sequence.
1.   Power ON all of the connected equipment.
2.   Plug the supplied power cord into the AC inlet of the projector.
3.   Press the On/Standby button on the projector or remote control. The lamp will turn on and an image will 
appear and grow brighter on the screen.
4. If the security feature is activated, enter the 4-digit PIN code.
a. Press the left/right arrow to move the cursor through each PIN field.
b. Press the up/down arrows to change the value in each field.
c. Press the Trigger button on the remote to enter the PIN access code.
PIN Code
5. Check all ventilation slots and clear away any obstructions.
6. Extend or retract front adjustment foot to obtain best image height.
Note: Rotate foot for fine adjustment.
7. Turn the focus adjustment (top of projector) to obtain the best image sharpness.
Stand By Mode
When an image is not being projected, place the unit into standby mode.
1.    Press the On/Standby button on the Remote Control or the On/Off button on the I/O Box. When the 
message “Press the power button to turn the unit off” displays, press the On/Standby button again.
2.   The lamp will switch off and the power button will first turn red indicating the unit is in lockout and then 
after 90 seconds the button turns amber to indicate the unit is in standby mode.
Note: In standby mode, the cooling fans will continue to run for 5 minutes and then turn off. 
						

							22 Operator’s Guide
3M™ Super Close Projection System SCP716
© 3M 2009. All Rights Reserved.
ENGLISH
Menu Navigation
To display the on screen menus, press the MENU button on the remote control or I/O Module. Use the remote 
control Up/Down ARROW buttons to select the desired menu (see table below), then pull the TRIGGER button 
(bottom of remote control) to display it.
Use the remote control ARROW buttons within a submenu to select the various options displayed on the screen, 
then pull the TRIGGER button to initiate that option or setting.
To exit an on-screen submenu, press the MENU button.
Main Menu
The main menu is the first system menu to display when the MENU button is pressed. Click on the menu icons 
to display the desired submenu.
Main Menu
Menu Icon Menu Description
Input Menu – Select the desired computer or video input source.
Picture Menu – Adjust the following picture features: mode, brightness, contrast, color 
intensity, tint, sharpness, video noise reduction, aspect ratio, and menu reset. Note: Displays 
only when input source is connected.
AdvancedAdvanced Picture Menu – Adjust the following settings for the detected signal source: over 
scan, brightness/color, horizontal position, vertical position, frequency, phase, & menu reset.
Audio Menu – Adjust the following audio settings: volume, mute, audio input (stereo mini-1, 
stereo mini-2, RCA), menu reset.
Setup Menu – Select or adjust the following settings: menu languages, auto shutoff timer, 
keystone, lamp hours, lamp mode, fan mode, projection mode, factory reset, PIN code and 
menu reset.
Information Menu – Display the current system information: input resolution, H/V 
frequency, lamp hours, system hours, IP address/net mask/gateway for I/O module Ethernet 
interface, user revision. 
						

							23 Operator’s Guide 3M
™ Super Close Projection System SCP716
© 3M 2009. All Rights Reserved.
ENGLISH
Input Menu
The Input Menu, shown below, is used to select the desired computer or video input source to be displayed on 
the projector.
InputInput Source: Computer 1
Computer 1 / Component 1 
Computer 2 / Component 2 
RCA Video 
S-Video
Feature Description
Main Input Select the Input source to be displayed on the projector.
1. Computer 1 / Component 2 [Computer 1 = default]
2. Computer 2 / Component 2 [Displays only when I/O module is connected]
3. RCA Video (Composite video)
4. S-Video 
						

							24 Operator’s Guide
3M™ Super Close Projection System SCP716
© 3M 2009. All Rights Reserved.
ENGLISH
Picture Menu
The Picture Menu, shown below, is used to adjust the picture settings to display the best possible image.
PictureInput Source: Computer 1
Picture Mode Enhanced PhotoX
Brightness 50 |···········z············|
0 5 t s a r t n o C |···········z············|
Color 50 |···········z············|
Hue 0 |···········z············|
Sharpness 0 |···········z············|
Video Noise Reduction On
Aspect Ratio          Full Screen
Advanced
ResetX
Feature Description Range Default
Picture ModeSelect the best mode to optimize the 
projector image.
1. Max Brightness
2. Enhanced Photo
3. Photo
4. EnhancedN/AVGA-Max Brightness
Video-Enhanced Photo
BrightnessAdjust brightness (low to high) of 
displayed image0–100 50
ContrastAdjust the contrast (dark to light) in the 
displayed image0–100 50
Color *
SEENOTE	Adjust the intensity of color in the 
displayed image0–100 50
Hue *
SEENOTE	Adjust the balance of red (-) to green (+) 
for video signals.-15–+15 0
SharpnessAdjust the displayed image to look sharper 
or softer-15–+15 0
Video Noise Reduction Turn noise reduction ON or OFF N/A Off
Aspect RatioSet aspect ratio to:  [Full Screen or 16:9 or 
Native]N/A Full Screen
AdvancedNavigate to the Advanced picture setting 
menu.  This option is for Computer/
Component input and only displays when 
the I/O Module is connected.N/A N/A
Reset Reset values in this menu only N/A N/A
* Note: Tint/Hue can only be adjusted for S-Video and RCA video input signals 
						

							25 Operator’s Guide 3M
™ Super Close Projection System SCP716
© 3M 2009. All Rights Reserved.
ENGLISH
Advanced Picture Menu
The Picture Menu with the Advanced option selected, shown below, is used to adjust the projected image for 
Computer and Component inputs only.
PictureInput Source: Computer 1
Over Scan 97 |···········z············|
Color / Brightness 10 |·······················z|
Horizontal Position 0 |···········z············|
Vertical Position 0 |···········z············|
Frequency 0 |···········z············|
Phase 0 |···········z············|
ResetX
Feature Description Range Default
Over ScanAdjust cropping of image boundaries from 90th to 
100th percentile (increments of 1 percent).90–100Video = 97 
VGA = 100
Brightness / ColorAdjust the white peaking value of the DMD.
LOWESTWHITEPEAKINGVALUEHIGHESTVALUE	0–10Computer = 10
Video = 3
Horizontal
PositionAdjust horizontal position of projected image.
/NLYFOR#OMPUTEROR#OMPUTERINPUTSOURCE	N/A 0
Vertical PositionAdjust vertical position of projected image.
/NLYFOR#OMPUTEROR#OMPUTERINPUTSOURCE	N/A 0
FrequencyAdjust the horizontal width of the projected image.
/NLYFOR#OMPUTEROR#OMPUTERINPUTSOURCE	-50–+50 0
PhaseAdjust clock phase to reduce image distortion.
/NLYFOR#OMPUTEROR#OMPUTERINPUTSOURCE	-15–+15 0
Reset Reset values in this menu only  N/A N/A 
						

							26 Operator’s Guide
3M™ Super Close Projection System SCP716
© 3M 2009. All Rights Reserved.
ENGLISH
Audio Menu
-ENUDISPLAYSONLYIF)/-ODULEISCONNECTED	
The Audio Menu, shown below, is used to adjust the audio settings and select the audio input source to play 
through the projector.
AudioInput Source: Computer 1
Volume 10 |···········z············|
Mute OffX
Audio Input¥Stereo Mini 1
Stereo Mini 2
RCA
t e s e RX
Feature Description Range Default
Volume Adjust volume level (0 = muted, 20 = full volume) 0–20 10
Mute Turn mute mode ON and OFF N/A OFF
Audio InputSelect the audio input source to process.
   Stereo Mini 1 – VGA/Component
   Stereo Mini 2 – VGA2/Component
   RCA – S-Video/ComponentN/A PC
Reset Reset values in this menu only  N/A N/A 
						

							27 Operator’s Guide 3M
™ Super Close Projection System SCP716
© 3M 2009. All Rights Reserved.
ENGLISH
Setup Menu
The Setup Menu, shown below, is used to configure the basic projector operating parameters.
SetupInput Source: Computer 1
Language EnglishX
Auto Shutoff Minutes Off |···········z···········|
Keystone 0 |···········z···········|
Reset Lamp HrsX
Lamp Mode NormalX
Fan Mode NormalX
Projection Mode   Front ProjectionX
Factory Reset AllX
AdvancedX
t e s e RX
Feature Description Range Default
Language Select the language for menu displays
[1-English, 2-French, 3-Spanish, 4-Deutsch, 5-Italian, 
6-Japanese, 7-Mandarin Traditional, 8-Mandarin 
Simplified, 9-Korean]N/A English
Auto ShutoffSet the number of idle minutes (no input source detected 
and no commands issued) before the projector will 
automatically shut off. 0–60 10
KeystoneVertical keystone adjustment.
   Stereo Mini 1 – VGA/Component
   Stereo Mini 2 – VGA2/Component
   RCA – S-Video/Component-15–+15 0
Reset Lamp Hours
Reset lamp hour status indicator.  3EE)NFORMATION-ENU.N/A N/A
Lamp Mode Bright, Normal, ECO N/A Normal
Fan Mode Normal, High N/A Normal
Projection Mode1-Front Projection, 2-Rear Projection, 3-Front Ceiling, 
4-Rear CeilingN/AFront
Projection
Factory Reset Reset all menu items to FACTORY DEFAULT settings N/A N/A
Advanced Select the Advanced Setup Menu. N/A N/A
Reset Reset values in this menu only  N/A N/A
27 © 3M 2006. All Rights Reserved.
ENGLISH 
						

							28 Operator’s Guide
3M™ Super Close Projection System SCP716
© 3M 2009. All Rights Reserved.
ENGLISH
Advanced Setup Menu
The Advanced Setup Menu, shown below, is used to initiate the PIN code feature (turn On/Off) and set the 
PIN code.
Setup PINInput Source: Computer 1
PIN Authentication OffX
Network Control OnX Change PIN ·X
Feature Description Range Default
PIN Authentication Turn the PIN code security feature On or Off. N/A Off
Set PIN codeChange the 4-digit PIN access code as desired.  
.OTE7HEN0).SECURITYISENABLEDTHE0).ACCESS
CODEWILLAUTOMATICALLYSETTOTHEDEFAULTVALUE0–9 3349
Network ControlTurns the network control function on and off.  The 
network control feature allows a computer to open 
the control web page on I/O module and control the 
projector. 
To view the control web page, connect the I/O 
module into the local area network and type the 
I/O module's IP address into the address bar of a 
web browser. (The IP address can be found in the 
projector’s information menu. See the next page.) 
The control web page will display. A RS-232 and 
network control guide is available at www.mmm.
com\meetings in the Technical Documents section.On/Off On
28
ENGLISH 
						

							29 Operator’s Guide 3M
™ Super Close Projection System SCP716
© 3M 2009. All Rights Reserved.
ENGLISH
Information Menu
The Information Menu, shown below, is used to display current projector configuration settings.
InformationInput Source: Computer 1
Input Resolution 1024 x 768
H Frequency 31.75 KHz
V Frequency 60 Hz
Lamp Hours 1235
System Hours 2356
IP Address 192.168.1.10
Net Mask 255.255.255.0
Gateway 192.168.1.1
User Ver. 0.0.8
Feature Description
Input Resolution Displays the current input Resolution
H Frequency Displays the current input H-Frequency
V Frequency Displays the current input V-Frequency
Lamp Hours Displays the current lamp operating hours for the installed lamp
System Hours Displays the current total system time accumulated
IP Address  *
SEENOTE	Displays the current IP Address for the I/O module Ethernet interface
Net Mask *
SEENOTE	Displays the current Net Mask for the I/O module Ethernet interface
Gateway *
SEENOTE	Displays the current gateway for the I/O module Ethernet interface
User Revision Displays the current User Version
* Note: This field displays only when the I/O Module is connected. 
						

							30 Operator’s Guide
3M™ Super Close Projection System SCP716
© 3M 2009. All Rights Reserved.
ENGLISH
Machine Specifications
Item Specification
Acoustic Noise LevelNormal Mode: Typical 32 dB(A)
ECO Mode: Typical 35 dB(A)
Auto Detect & InstallAutomatically recognizes the connection of I/O module
Automatically saves user adjustments
Computer CompatibilityHorizontal Sync: 69 kHz
Vertical Sync: 85 Hz
Conditions for usage environmentRel Humidity:10-80%
Altitude: 0-2286m
Temperature: /10-35C (50-95F)
Dimensions 328.94 x 264.0 x 116.43 mm (13.2 x 10.6 x 4.7 inches)
DMD Native Resolution 1024H x 768V (XGA)
Focus Manual Adjustment
Input / Output TerminalsVGA (mini D-sub 15-pin) connector
Control connector
USB (A-B)
AC power outlet
Input rating 100-240V AC, 50-60 Hz, 4.0A
Lamp Life3000 hrs at 300W Bright mode
5000 hrs at 180W ECO mode
LanguagesEnglish, French, Spanish, Deutsch, Italian, Japanese, Chinese 
Traditional, Chinese Simplified, Korean
Lens Focal Length = 6.95 mm
Power Consumption 300W normal operation, 5W standby mode
Video CompatibilityNTSC: M, N, 3.58Mz, 4.43 MHz
PAL: B, D, G, H, I, M, N
SECAM
Wall/Ceiling Mount capability Three screw holes
Weight 4.5kg   (10 lbs)
Note: Designs and specifications are subject to change without notice.