Aaxa Projector M4 Pico User Manual

							aaxa
TECHNOLOGIES
User Guide
 M4 Pico Projector 
						

							Caution!
WARNING:  Please use this product as instructed.  Misuse may cause 
injury or death.
DO NOT use while driving
DO NOT expose to water or wet 
surfaces.  Electric shock may occur.
DO NOT expose the projected LED 
image to your eyes or the eyes of 
others
 
DO NOT block or restrict airflow 
from ventilation holes as this may 
cause the projector to overheat
Keep the projector, battery, or  
charger away from any heat sourcesCaution for Battery Use
• Do not pierce or puncture the battery 
with sharp objects
• Do not heat the product or expose it to 
high temperature.
• Do not wet it or place it in any liquid
Caution for Headphone Use• Prolonged use at high volume may 
impair your hearing.
• High volume during walking or driving 
may cause distractions and result in 
injury or death 
						

							Table of Contents
1
2
3
4
5
6
7
8
Connecting a Micro SD Card
Connecting to a USB Host
Chapter 3: Menu Screens
Chapter 4: Technical Details
Troubleshooting
Specifications1
Chapter 1: M4 at a glance
Main Unit Front/Back
Remote & Keypad
Accessories 
  
Main menu
Video Player Menu
  Video FAQ
Photo Viewer Menu
  Photo FAQ
Music Player Menu
  Music FAQ
Setup Menu
Keystone Adjustments
Connecting to Speaker or 
Headphones
Chapter 2: Getting Started
Powering On / OFF
Focus Adjustment / 
Throw 
Distance
Battery Pack Information
Connecting to a Computer VGA
Connecting to a Computer HDMI
Connecting to HDMI Video
DTV Setup
10
12
14
  17 18
 20
    22
23
25
26
28
29
31
32
3941 
						

							2
Chapter 1
Power On/Off
 
Main Menu 
Navigation
Main Unit Front/BackPower Button
M4 at a Glance
Power Switch
Focus Wheel
Component PortMicroSD Card Slot
HDMI Input
       USB 
       TV Antenna3.5mm AudioDC Adapter     VGA 
						

							PWRGamma
MENUUUPEXIT
VOL-
OKVOL+
I
U/DDOWNR/L
VGA MenuAV
Menu
Remote & Keypad
3
Power On/Off
 
Select Source
Media Player Menu 
NavigationInputExit/Back
Direction PadLED Lights
Keystone Adjustment                                Keystone Adjustment
Main Menu Navigation
  Volume Adjustment                     Volume AdjustmentOn / Off
Both the keypad and remote can be used to navigate through the menus.  The Main Menu Navigation on the remote functions exactly the same as the directional pad on the M4 unit for all modes except DTV mode.  In DTV mode the remote control is necessary to perform the “scan” feature 
						

							Accessories
4
*Under various circumstances, the actual accessories may be different from 
those shown in the pictures above.
PWRGammaMENUUUPEXIT
VOL-OKVOL+
I
U/DDOWNR/LVGA MenuAV
Menu
Internal Battery   
(pre-installed)
Remote
Power Adapter 
						

							Getting Started
5
Powering ON the projector
Chapter 2
Powering OFF the projector
Note:  The  M4  Projector  battery  does  not  charge  when  it  is  in  operation.   For  first  time 
operation charge the battery for 120 minutes to ensure a full charge.
1. Connect the power adapter to the projector and power outlet2.  Switch the On / Off switch on the side of the projector to the “ON” position
There are two idle modes for the projector.  Off and Standby.  The Off 
mode complete turns off the projector.  The Standby mode allows the projector
 to be turned on with the remote control.  The standby mode consumes a little 
battery power when left in this mode.
1. To fully power off the projector, switch the On / Off switch on the side of the projector         to the Off position2. To put the projector in Standby mode press the POWER button on the keypad3. A window will pop up asking Do you want to power off?4.     Press the power button again to put the projector in Standby mode 
						

							Focus Adjusment / Throw Distance
Focus Adjustment
6
DIAGONAL
 SCREEN SIZE
16:9 Aspect  Ratio
Throw Distance Chart
•    Adjust the focus wheel left and right until the image 
becomes clear.
Screen Size (Inch) 102968982756861554841342721
Distance (Meters)32.82.62.42.221.81.61.41.210.80.6
Throw Ratio 1.360 
						

							7
1. Remove the three screws 
circled in blue holding the M4 
battery compartment.
2. Disconnect the battery harness 
to the battery receptacle on the 
PCBA
**Please note that the battery pack is pre-installed in the M4. The instructions 
below is how to remove the battery unit if replacement is needed.
3. Remove the battery and 
replace with new battery unit
using previous instructions 
in reverse order.Battery Pack Installation 
						

							Connecting to a Computer via VGA
Connect the large end of the 
8
VGA Cord
to your computer’s
VGA Adapter
Step 1:
Step 2:
Step 3:
In the Main Menu 
Select “VGA” icon Select “INPUT” icon 
to your M4
VGA Cord
Connect the large end of the
VGA Adapter