Acco Nobo Digital DLP Projector X25C User Manual

							11
... English
Powering On the Projector
1.  Remove the lens cap. 
2.  Ensure that the power cord and signal cable are securely 
connected.  The Power LED will flash green.
3.  Turn on the lamp by pressing “Power/Standby” button on 
the control panel.  The Power LED will turn green.
The first time you use the projector, you can select your 
preferred language from the quick menu after the startup 
screen display.
4.  Turn on your source (computer, notebook, video player,etc.).  
The projector will detect your source automatically.
If you connect multiple sources at the same time, use the
  “Source” button on the control panel or remote control  
 to switch.
Powering On/Off the Projector
Turn on the projector 
first and then the signal 
sources.
1
Power/Standby
2
Lens Cap
Quick Menu

Select Language
English
 Deutsch
Français
Italiano
Español
Português
Nederlands
Polski
Press Enter to Set
Installation
1
2 
						

							12
English ...
Installation
Warning Indicator
  When the “LAMP” indicator lights solid red, the projector 
will automatically shut itself down. Please contact your local 
reseller or service center (refer to pages 33~34). 
  When the “TEMP” indicator lights solid red for about 60 
seconds, it indicates the projector has overheated. The 
projector will automatically shut itself down.
  Under normal conditions, the projector can be switched on 
again after it has cooled down.  If the problem persists, you 
should contact your local dealer or our service center 
(refer to pages 33~34). 
  When the “TEMP” indicator flashes red for about 5 seconds, 
it indicates the fan failed. Please contact your local dealer or 
our service center (refer to pages 33~34). 
Powering Off the Projector
1.   Press the “Power/Standby” button to turn off 
the projector lamp, you will see a message “
” displayed on the pro-
jector ’s screen. Press the “Power/Standby” button again 
to confirm, otherwise the message will disappear after 5 
seconds.     
  Please note that if the 
 key is pressed instead,  the projec-
tor will enter the “Picture Mute” mode and no image will 
be displayed.  To exit the “Picture Mute” mode, press the 
“Power/Standby” button again. 
2.  The cooling fans continue to operate for about 30 seconds 
for cooling cycle and the Power LED will turn green.  When 
the Power LED begins flashing, the projector has entered 
standby mode.
  If you wish to turn the projector back on, you must wait 
until the projector has completed the cooling cycle and has 
entered standby mode.  Once in standby mode, simply press 
“Power/Standby” button to restart the projector.
3.  Disconnect the power cord from the electrical outlet and the 
projector.
4.  Do not turn on the projector immediately following a power 
off procedure. 
						

							1
2
3
3
13
... English
Installation
Adjusting the Projected Image
Adjusting the Projector Image Height
Tilt Adjusting 
Feet Elevator Foot
23
Elevator Button
The projector is equipped with an elevator foot for adjusting the 
image height.
  To raise the image:
1.  Press the elevator button 
.
2.  Raise the image to the desired height angle  , then release  
  the button to lock the elevator foot into position.
3.  Use   to fine-tune the display angle. 
  To lower the image:
1.  Press the elevator button.
2.  Lower the image, then release the button to lock the  
  elevator foot into position. 
3.  Use   to fine-tune the display angle.
1
3 
						

							15
... English
User Controls
Remote Control Control Panel
Control Panel & Remote Control
There are two ways for you to control projector functions: 
Remote Control and Control Panel.
  Using the Control Panel
 Power/Standby  
Refer to the “Power On/Off the Projector” section on pages
   11-12.
Source
Press “Source” to choose RGB, Component-p, Component-i,
    S-Video, Composite Video and HDTV sources.
Menu
Press “Menu” to launch the on-screen display (OSD) menu.
    To exit OSD, press “Menu” again.
 Keystone/
Adjusts image distortion caused by tilting the projector (±15
   degrees).
Four Directional Select Keys 
Use to select items or make adjustments to your
   selection.
Enter
Confirm your selection of items.
 Re-Sync 
Automatically synchronises the projector to the input source. 
						

							16
English ...
User Controls
  Using the Remote Control
 Power  
Refer to the “Power On/Off the Projector” section on pages 11-12.  
 Re-Sync
Automatically synchronises the projector to the input source.
  Volume + / - (Vol+/Vol-)
Increases/decreases speaker volume.
 Reset
Changes the adjustments and settings to the factory default
   value.
Hide
Press “Hide” to hide image, press again to restore display of the
   image.
 Keystone  / 
Adjusts image distortion caused by tilting the projector (±15
   degrees).
 Freeze
Press “Freeze” to pause the screen image.
 D-Zoom
Press “D-Zoom” button to zoom in on an image.
 Display Mode
Select the display mode from PC, Movie, Game, sRGB and User.
  Four Directional Select Keys 
Use to select items or make adjustments to    
   your selection.
 Enter
Confirm your selection of items.
 Menu  
Press “Menu” to launch the on-screen display menu.  To exit
    OSD, press “Menu” again.
 VGA1
Press “VGA1” to choose VGA1 connector.
 VGA2
Press “VGA2” to choose VGA2 connector.
 S-Video
Press “S-Video” to choose S-Video source.
 Composite
Press “composite” to choose composite video source. 
						

							The Projector has multilingual On Screen Display menus that 
allow you to make image adjustments and change a variety of 
settings. The projector will automatically detect the source. 
How to operate 
1.  To open the OSD menu, press “Menu ” on the Remote Control
  or Control Panel.
2.When OSD is displayed, use   keys to select any item in the
  main menu.  While making a selection on a particular page, press  
 or “Enter” key to enter sub menu.
3.Use  keys to select the desired item and adjust the   
 settings by 
  key.
4.Select the next item to be adjusted in the sub menu and adjust as
  described above.   
5.Press “Menu ” to confirm, and the screen will return to the main
 menu.
6.  To exit, press “Menu ”again.  The OSD menu will close and the
  projector will automatically save the new settings.
On Screen Display Menus
Main Menu
Sub Menu
Setting
17
... English
User Controls 
						

							Menu Tree
English/Deutsch/Français/Italiano/Español/
Português/Nederlands/Polski
18
English ...
User Controls 
						

							Language
 Language
  Choose the multilingual OSD menu . Use the   or  key to select
  your preferred language. 
  Press “Enter” to finalise the selection. 
19
... English
User Controls
English
Français
Deutsch
Italiano
Español
PolskiPortuguês
Nederlands 
						

							20
English ...
User Controls
Image-I
 Display Mode
There are many factory presets optimised for various types of  
 images.  
   PC: For computer or notebook.
   Movie: For home theater.
Game : For game.
   sRGB: For standard colour.
   User: Memorise user ’s settings.
 Brightness
Adjust the brightness of the image.
Press the 
 to darken the image.
Press the 
 to lighten the image.
 Contrast
The contrast controls the degree of difference between the lightest  
  and darkest parts of the picture. Adjusting the contrast changes  
  the amount of black and white in the image.
  Press the 
 to decrease the contrast.
Press the 
 to increase the contrast.
  Keystone (Keystone Correction)
Adjust image distortion caused by tilting projector. (±15 degrees)
 Colour
Press “Enter” to adjust the red, green and blue colours. 
 White Peaking
Use the white peaking control to set the white peaking level of  
  DMD chip. 0 stands for minimal peaking, and 10 stands for