Accusplit Pedometer AE140SXL8up User Manual
Have a look at the manual Accusplit Pedometer AE140SXL8up User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 150 Accusplit manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
23 45 67 2 Operating Instructions ACCUSPLIT®EAGLE AE140SXL PEDOMETER Functions• Step counter. • Automatic Activity Timer. • Distance in mi or km. For complete Function Specifications, go to page 31.Key Features• Built around the Japanese-made JW200 PedometerEngine™ Step Sensor, the current gold standard for accuracy. • Extra Large Digits. • The ACCUSPLIT exclusive case makes this the slimmest available pedometer built around the JW200 Step Sensor. • Chromed, Spring Steel clip resists breakage. • Case includes two leash slots, for attaching safety leash on either side. Made from tough polycarbonate plastic. • Step filter, can be set from 0-5 steps to further increase accuracy. HOW TO OPEN YOUR PEDOMETER See diagrams at right. The cover must be closed for the pedometer to work. USE IT NOW! Your pedometer is preset with standardized settings that allow you to use it now! You can customize the settings later. Skip to pages 13-16 to use it now! SETTING UP YOUR PEDOMETER It’s a good idea to set up your pedometer before first using it. To record your distance accurately, you will need to set your stride length. See page 9 when you are ready to set up your unit. ACCUSPLIT EAGLE DigiwalkerXL.comSTEP TIME DIST CALSET4728MODERESETS3–S1, S2, S4S3+140SXL Getting Acquainted • Press the MODE button to cycle through the display modes (Steps, Activity Time, …). See page 20 and Specifications for details. • The RESET button sets your counts back to zero. See page 24 for details. MODES • STEP: STEP mode shows step count. • TIME: AUTO ACTIVITY TIMER MODE shows total activity time in min and sec. • DIST: DISTANCE mode shows distance traveled (mi/km). STEP TIME DIST SET DIGI-WALKERXL.COM 140SXLS3-S3+S1,S2,S4JW200 Mode indicator Steps Counted MODE Button RESET Button (yellow) ACCUSPLIT, Inc. 2290A Ringwood Ave., San Jose, CA 95131 800-965-2008 • 925-226-0888 • FAX 925-463-0147 www.ACCUSPLIT.com/support • [email protected] Eat Right! Walk More! Live Well! The ACCUSPLIT Lifes t yle970-084Sept 07
10 8 11 9 1213 1514 SETTING PROCEDURE ACCUSPLIT products use a common setting procedure known as “S1- S2-S3-S4.” Here’s how it works: Press S1 for 2 seconds: Enter the SET mode Press S2: Change the field to be set Press S3: Change the field value Press S4 for 2 seconds: Exit the SET mode You can enter and exit Set mode from any of the regular display screens. Entering set mode Press and hold the S1 (MEMORY) button for 2 seconds. The display will start to flash, showing that you’ve entered SET mode. Setting Stride Length1. You will see the mode indicator bar underneath DIST and the “in” indicator come on. The display will show a flashing number, which is your Stride Length set point (in inches). 2. Press the S3 + (MODE) button to increase the Stride Length (in increments of ¼ inch), and press the S3- (RESET) button to decrease the Stride Length. Hold the buttons down to change values quickly. Finding Your Stride Length: Your stride length is the length of one of your steps, measured from “toe to toe.” To measure, walk 10 steps with your normal stride and measure the TOTAL DISTANCE from the toe of your starting step to the toe of your 10th step (see diagram below). Divide the TOTAL DISTANCE by 10, and multiply the decimal portion by 12 to find your stride length in feet and inches. Example: You walk 23 feet and 6½ inches in 10 steps. Convert to feet only = 23.542 feet (6½ ÷ 12 = 0.542). Divide by ten to get the stride length in feet = 2.354 feet. Now, convert back to feet and inches to get your stride length = 2 feet 4.25 inches (0.354 × 12 = 4.25). 10 steps Exiting Set ModePress and hold the S4 button for 2 seconds. The unit will exit setting mode – no values will be flashing anymore. Note: The unit will save any changes and exit set mode after 30 seconds unattended. WEARING YOUR PEDOMETERGently slide the pedometer onto your belt or the top edge of your pants or skirt. It should fit snugly and level, above one knee. The strong steel clip makes it easy. Note: The pedometer should be as vertical as possible. Walkers with larger stomachs may find it helpful to wear the pedometer farther back on the body, toward one hip. The cover must be closed for the pedometer to work. yes no To avoid losing or dropping your pedometer, use the included leash and clip to fasten the pedometer securely to your clothing. Attaching the Leash1. Attach the pedometer to the leash by looping the thin side of the leash through one of the leash slots on the sides of the pedometer case, near the bottom of the unit. 2. Put the pedometer onto your clothing as discussed above. 3. Attach the alligator clip to a belt loop or the top edge of the pants or skirt. Note: You can also use a safety pin to fasten the leash to your clothing, loop the leash through your belt or belt loop, or use a badge holder. First, loop leash through slot on side of pedometer Next, clasp clothing Or, loop a badge holder, then put into pocket (Badge holder not included) Or, loop a belt or belt loop STEP TIME DIST SETDIGI-WALKERXL.COM 140SXLS3-S3+S1,S2,S4JW200 in Setting Stride Length Stride Length Flashes “in” indicator for inches
To replace the battery: 1. Insert a coin into the slot on the bottom of the case, and twist to loosen the faceplate. Remove faceplate and set aside. 2. Locate the battery holder as seen on sketch. Pull out the old battery, and push a new LR-44 battery into the holder, with positive terminal (+) facing up. 3. Snap faceplate back into place, hooking the bottom two tabs first, then closing by pressing together at the top two tabs. 1819 1617 21 2223 VIEWING YOUR RESULTSOnce you put on your pedometer with the cover closed, it will automatically begin to record your steps, activity time, and distance. Repeatedly press the MODE button to cycle through the pedometer modes: STEPS g TIME g DISTANCE g STEPS Time and Distance are counted automatically whenever steps are being counted. • TIME is time spent in step activity. • DISTANCE is simply stride length x steps. Note: For extra accuracy, the default Step Filter Setting is 1. See page 19 to learn more. 20 RESETTING YOUR PEDOMETERMost people prefer to reset counts daily. To reset your counts: From STEP, TIME, or DISTANCE mode, press and hold the yellow RESET button for at least 2 seconds. You’ll see the values all go back to zero. OTHER SETTINGS The Step Filter and Unit of Measurement settings are accessed through a special “deep set” mode. To enter this mode, press and hold the S1 button for 4 seconds. The screen will display a single digit. From within Deep Set mode, press the S2 button to cycle back and forth between the Step Filter set point and Choice of Unit System. CHANGING STEP FILTER SETTING While the JW200 PedometerEngine™ Step Sensor is extremely accurate, some people like to have the ability to filter out false steps. Therefore, the unit has a variable setting step filter, to allow fine-tuning to your specific preferences. You can set the value to any value from 0 – 5 steps. For example, if the filter is set to “3”, the unit will wait to start counting steps until more than three steps have been taken in less than five seconds. Press S3+ (MODE) or S3– (RESET) to change the Step Filter Setting. CHANGING UNITS (English vs. Metric) The Pedometer can display either in English units (in, mi, and lb - this is the default), or in Metric units (cm, km, and kg). From within Deep Set mode (see pg. 18), press the S2 button to cycle back and forth between setting the Step Filter set point and Choice of Unit System. The unit will show either “US” or “EU” (for European Union) depending on the unit system chosen. If you change units after using the pedometer, the unit will convert all of your data into the new unit system when you exit Deep Set model. You can check to see which system of units you are using by seeing which measurement units are displayed on the Stride and Weight setting screens. Press S3+ (MODE) or S3– (RESET) to change the Measurement Mode. Press and hold S4 for 2 seconds to exit Deep Set Mode. Note: The unit will save any changes and exit set mode after 30 seconds unattended. REPLACING THE BATTERY AND MASTER RESETWhen the display starts to dim or goes blank, it is time to replace the battery. If the display is not uniformly dim or blank , and appears to display “erroneous data”, do a Master Reset by pressing all 3 buttons simultaneously for 3 seconds and then release. The display should go blank, then turn all segments on, then display 0 steps in Step Mode. Note: All the settings will return to their default setting values. If you need to change the battery, the settings will also revert to default settings. Set Step Filter set point STEP TIME DIST SETDIGI-WALKERXL.COM 140SXLS3-S3+S1,S2,S4JW200 Set measurement mode “US” (English) or “EU” (Metric) Can be set from 0-5 steps STEP TIME DIST SETDIGI-WALKERXL.COM 140SXLS3-S3+S1,S2,S4JW200 Battery
2627 2425 SPECIFICATIONS, FEATURES, and FUNCTIONS Description of Functions• Counts Steps up to 99,999 then rollover. • Counts Time spent in step activity, up to 999 Min 59 sec, then rollover. Automatically counts whenever step activity is occurring. • Counts distance traveled during step activity, up to 999.99 mi or km, then rollover. Automatically counts whenever step activity is occurring. • Adjustable stride length for greater distance accuracy (default setting is 21 in/53 cm, but can be set from 12-72 in (30-180 cm), in 0.25 in / 1 cm increments. • Adjustable Step Filter (default setting is 1 step, but can be set from 0-5 steps) to increase step count accuracy. • Switchable between English and Metric units, without losing data (default setting is English units). REGISTER NOW Please return your AE140SXL Registration to the Repair Center address in the warranty, and we will let you know about future products. Email (preferred) User NO-PROOF-OF-PURCHASE LIMITED WARRANTYFree service for first year of ownership; $12 fee for service thereafter. See label inside unit for date. See www.ACCUSPLIT.com/support for details Battery, replacing . . . .22-23 Current day’s results, viewing. . . . . . . . . . . . . .16 Setting Mode, exiting. . . .12 Open your pedometer . . . .4 Safety Leash . . . . . . . .14-15 Setting up pedometer. .8-12 Step Filter Setting, change . . . . . . . . . . .18-19 Stride Length, setting. . . . . . . . . . . . .8-12 Unit of measure, changing. . . . . . . . . .18-21 Wearing pedometer . . . . .13Warranty . . . . . . . . . . . . . .26 INDEX