Accusplit Stopwatch AX602FY User Manual

							b-1
ACCUSPLIT, Inc.
6120 Stoneridge Mall Rd., Suite 210 Pleasanton, CA 94588 USA
800-965-2008  •  925-226-0888  •  FAX 925-463-0147
www.ACCUSPLIT.com  •  [email protected]
980-312
ACCUSPLIT®
E X CLUSIVE
AX602FY
STOPWATCH
OPERATING
INSTRUCTIONS
2-3
ACCUSPLIT® AX602FY 
DIGITAL 100 MEMORY STOPWATCH 
WITH SPLIT AND LAP TIME MEASUREMENT AND 
STROKE/FREQUENCY MEASURING FUNCTIONS
FEATURESThe Quartz Stopwatch is a digital 
stopwatch featuring memory and 
stroke/frequency measuring func-
tions. In addition, the stopwatch 
is water resistant. Therefore, it is 
suitable for aquatic sports or use 
in rainy weather.
•  STOPWATCH
  The stopwatch can measure up  
  to 10 hours in 1/100 seconds.
•   SPLIT TIME/LAP TIME 
 MEASUREMENT
  Up to 100 split times and lap 
  times can be measured.
2
•   LARGE-SIZED THREE-ROW DISPLAY PANEL
  Total elapsed time, split time and lap time are displayed at the same 
  time in separate rows, and they can be measured successively 
  without releasing split or lap time measurement.
•   MEMORY FUNCTION
  Up to 100 measurements can be stored in memory, and they can be 
  recalled after the measurement is over.
•   TIME/CALENDAR DISPLAY
  Year, month, date, hour, minutes, and seconds can be displayed while 
  the stopwatch is not in use.
•   BATTERY LIFE INDICATOR
  Lithium battery CR2032 or equivalent is used.
•   ACCUSPLIT “X” CASE
  Exclusive professional case with no-fail buttons.
3 
						

							4-5
There are four buttons as 
indicated in the illustration.
TIME/CALENDARdisplay
STOPWATCHdisplay
4
STROKE/FREQUENCY MEASURING MODE
STROKE/FREQUENCYMEASURING display
A
C
B
D
5
TIME/CALENDAR SETTING
1. Press “D” to show the time/calendar display. The time/calendar display 
    mark will appear.
2. S1 – Press and hold “B” for 2 seconds until seconds display begins \
 ashing. TIME/CALENDAR display mark
A
C
B
D
Year
Month and date
Seconds
Minutes
Hour
ACCUSPLIT products use a common setting procedure known as S1-S2-S3-S4.
S1  (2 sec) - Enter set function OR 
S1  (4 sec) - Enter set function & 
  clear the current settings
S2 – Select  eld to be set 
  (selected  eld will  ash)
S3 – Set  eld to desired settings
S4 – Exit setting function
6-7
6
7
STOPWATCH
Press “D” in the TIME/CALENDAR display to show the STOPWATCH display. 
The STOPWATCH display mark will appear.
The STOPWATCH can measure up to 10 hours in hours, minutes, seconds and 
1/100 seconds.
  •  Before using the stopwatch be sure to reset the digits to “0:00:00.00\
”.
    When the stopwatch is stopped, press ”B” to reset.
    When the stopwatch is counting, press “A” to stop the measurement \
    and then press “B”.
A
C
B
D
STOPWATCH display mark Split time
Lap time
Total time (accumulated 
elapsed time)
Split/lap number
3. S2 – Press “B” repeatedly to select the digits ( ashing) to be adjusted. 
    With each press of “B,” the digits to be adjusted change over \
in the 
  following order. 
4. 
S3 – Press “A” to set the  ashing digits or reset the seconds to “00”.
  •  The digits move quickly if “A” is kept pressed.
  •  When the seconds digits count any number from ”30” to “59” a\
nd “A” is 
    pressed, one minute is added and the second digits are reset to “00”\
.
5.  S4  – After all the adjustments are completed, press “A” repeatedly\
 until watch 
  exits set mode and returns to the TIME/CALENDAR  display.
Notes:
1. Hour digits are displayed in the 24-hour indication.
2. Year digits can be set from 1988 to 2027. The calendar adjusts automatica\
lly for 
odd and even months including February of leap years.
 seconds  minutes  hour  year  month  date
    Note:  The watch exits set mode automatically after setting date. 
						

							8-9
AAB
  •  “Split time” refers to an elapsed time required to cover a distanc\
e from 
    the start to a given point.
  •  “Lap time” refers to an elapsed time required to cover a given sec\
tion 
    of the whole distance.
Lap time
Split time
Start
1. STANDARD MEASUREMENT
    Hour  Seconds
            Minutes        1/100 seconds
START
STOPRESET
8
2. ACCUMULATED ELAPSED TIME MEASUREMENT
9
START STOPRESTART
RESET STOP
Restart and stop 
of the stopwatch  can be repeated by pressing “A”.
BA
AA
10-11
10
3. SPLIT TIME/LAP TIME MEASUREMENT
Note:  When the number of stored measurements 
      exceeds 90,  ashing “FULL” appears, and when 
      it exceeds 100, a warning sound starts beeping.
B
A B
AB
BSTART SPLIT-LAP 1 SPLIT-LAP 2
RESET STOP
SPLIT-LAP 8
The split/lap time can 
be measured repeated  by pressing “B”.Split/lap number Split time
Lap time
Accumulated 
elapsed time
Finish time
11
The stopwatch can store up to 100 split times, 100 lap times and total e\
lapsed 
time. They are automatically entered into the memory.
  •  With each press of “C”, the time stored is recalled. The time can be 
    recalled successively by keeping the button pressed.
  •  To stop the recall of the stored data, press “A”, “B”, or “D”. The 
    measurements when the stopwatch was stopped will be shown. 
    Then, press “B” to reset the digits to “00”.
4. HOW TO USE THE MEMORY FUNCTION
B
CC
A
C
C
“RECALL” more
Finish time
Reset to “00” 
						

							12-13
12
  •  The time stored in the memory can be recalled even while the stopwatch 
  is measuring.
Notes:
1. Even if the digits are reset to “00”, stored times are not eras\
ed and can be 
  recalled by pressing “C” unless new measurement is started.
2. If the stopwatch is left untouched with the recalled times shown, the\
 display 
  will automatically return the STOPWATCH display in 1 to 20 minutes.
  •  To measure the lap time and split time while the stored data are being    
    recalled operate the buttons as follows.
    Press “B” to measure new lap time and split time.
    Press “A” to stop the measurement.
    Press “D” to return to the measurement mode.With each press of “C”
When the stopwatch is stopped Split time and lap time are recalled starting with the  rst ones.
When the stopwatch is measuring The times are recalled starting with  the last ones.BA
13
Press “D” to show the STROKE/FREQUENCY MEASURING display.
Start the measurement by pressing “A” and stop the measurement by \
pressing 
“A” after the third stroke was made. The number of strokes per min\
ute will be 
displayed. STOKE/FREQUENCY MEASURING
B Start
MeasuringStop Reset
A AB
Start Stop
STROKE/
FREQUENCY 
MEASURING  mode The number 
of strokes 
per minute  (23.2)
14-15
14
Notes:
1. During 1 second after the measurement has been started by pressing “\
A”, 
   ashing “180.0” is displayed. If the measurement is stopped by pres\
sing 
  “A”  during this period, “Err” will appear. If the measurement is not stopped 
  by pressing “A” after more than 18 seconds have elapsed, “Err”\
 will
  automatically appear. Therefore, note that measurable number of strokes 
  per minute is between 10 and 180.
2. If “B” is pressed while the measurement is stopped or “Err”\
 is shown, the 
  digits will be reset “0.0”. Even if the digits are not reset to “0.0” with the 
  measurement stopped or “Err” shown on the display, the measurement 
  can be started by pressing “A”.
Error
15
NO-PROOF-OF-PURCHASE  LIMITED WARRANTY See label on back of unit for details, or check 
http://support.ACCUSPLIT.com
REGISTER NOW Please return 
your AX602FY Registration to 
the Repair Center address in the 
warranty, and we will let you 
know about future products. Email (preferred)
User