Home > Acer > Notebook > Acer Aspire 4935 Service Guide

Acer Aspire 4935 Service Guide

    Download as PDF Print this page Share this page

    Have a look at the manual Acer Aspire 4935 Service Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 720 Acer manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Chapter 3111
    7.Run the left side Antenna cable as shown in the 
    hinge well to avoid trapping.8.Run the cable along the edge of the casing using 
    all available cable clips.
    9.Run the cable as shown and replace the adhesive 
    strip.10.Run the cable as shown and replace the adhesive 
    strip.
    11 .Run the cable along the edge of the casing using 
    all available cable clips.12.Replace the Antenna in the casing as shown and 
    secure it in place with the tape. 
    						
    							11 2Chapter 3
    13.Ensure that the securing pin is properly located. 
    						
    							Chapter 311 3
    Replacing the LCD Panel
    1.Align the LCD brackets with the six screw holes (three on each side) on the LCD Panel as shown.
    2.
    Replace the six securing screws in numeric order, from 1 to 3.
    3.Turn the panel over. Insert the LCD Panel cable 
    into the LCD Panel as shown (1). Secure the cable 
    by replacing the securing strip (2).4.Run the LCD cable as shown and press down 
    along the length of the cable to secure it in place.
    5.Insert the LCD panel into the casing back edge first 
    as shown.6.Ensure that the four locating pins are properly 
    seated before continuing.
    23
    121
    3
    2
    1 
    						
    							11 4Chapter 3
    7.Replace the Camera Module cable bundle in the casing as shown.
    8.Replace the three screws to secure the panel and grounding within the LCD module.
    IMPORTANT:When replacing the screws in the LCD brackets (red callout) do not use the screw holes 
    marked with ‘X’. These slots are reserved for the Bezel securing screws.  
    						
    							Chapter 311 5
    Replacing the Camera Module
    1.Reconnect the LCD cable to the Camera Module.2.Place the Camera Module in the casing as shown.
    3.Ensure that the locating pins are correctly seated.4.Insert the Camera Bracket left side first to engage 
    the securing clip.
    5.Lower the bracket into place as shown6.Replace the single securing screw. 
    						
    							11 6Chapter 3
    Replacing the LCD Bezel
    1.Place the Bezel on the casing bottom edge first 
    and press in the areas marked to snap it into place.2.Press down the sides of the bezel, working toward 
    the top edge.
    3.Press down the top edge to complete the process.
    IMPORTANT:Ensure there are no gaps between the casing and the Bezel.
    4.Replace the six securing screws and screw caps on the LCD bezel.
      
    						
    							Chapter 311 7
    Main Module Reassembly Procedure
    Replacing the CPU
    IMPORTANT:The CPU has a Pin1 locator that must be positioned corresponding to the marker on the CPU 
    socket.
    1.Place the CPU into the CPU socket as shown, taking note of the Pin1 locator.
    2.Using a flat-bladed screw driver, rotate the CPU locking screw 180° clockwise to secure the CPU in place.
    Socket
    Pin1 LocatorCPU
    Pin1 Locator 
    						
    							11 8Chapter 3
    Replacing the Thermal Module
    WARNING:To prevent damage to the Thermal Module or the CPU, hold the Thermal Module by both ends at 
    the same time.
    IMPORTANT:If the replacement Thermal Module does not include the thermal protection pad shown below, 
    reuse the original thermal protection pad with the new Thermal Module.
    1.Align and place the Thermal Module in the on the 
    mainboard as shown.2.Remove the four screws from the Thermal Module 
    numerically, from 1 to 4.
    3.Connect fan cable to the mainboard as shown.
    1
    4
    3
    2 
    						
    							Chapter 311 9
    Replacing the RJ-11 Port
    1.Replace the RJ-11 Port in the casing as shown.2.Place the cable bundle in the casing and apply 
    pressure to secure the adhesive in place.
    3.Run the cable along the cable channel using all 
    available cable clips.4.Replace the adhesive tape and insert the cable 
    through the casing as shown.
    5.Pull the cable through the casing completely.6.Turn the computer over and run the cable along 
    the cable channel using all available cable clips. 
    						
    							120Chapter 3
    7.Insert the cable through the casing to the top side as shown. 
    						
    All Acer manuals Comments (0)

    Related Manuals for Acer Aspire 4935 Service Guide