Acoustic Energy Loudspeaker Aelite On Wall User Manual

							Owner’s manual 
						

							Congratulations on choosing the Acoustic Energy AELITE
On Wall Loudspeakers.These powerful two-way
loudspeakers feature metal diaphragm technology and
are capable of outstanding performance. Please take a
few moments to read this manual. The advice it contains
will enable you to get the very best performance out of
your Acoustic Energy loudspeakers.
The AELITEOn Wallspeakers utilise metal cone mid-bass drive unit
technology, proven in our Reference Series. The rigid anodised alloy
cones ensure pure piston action and also act as heat sinks for the
bonded voice coils. These features provide exceptional clarity,
transparency, dynamics and power handling.
The tweeters - or treble drivers - are high-quality neodymium units
with silk fabric domes integrating smoothly with the rest of the
system. 
All drive units are fully magnetically shielded so that the speakers
can be used in close proximity to a TV screen or monitor for AV
applications.
The Acoustic Energy 
AELITEOn Wallloudspeakers use quality OFC
internal wiring, which enhances detail and transparency. 
The AELITE On Wallspeakers should be mounted on a solid wall or
partition using the fixing points that are provided on the rear. Rigid
support is essential for the speakers to develop their full detail and
dynamic performance. 
A drilling template is provided to ensure accurate spacing for these
fixings;  however a suitable fixing method should be chosen to suit
the wall construction. If in doubt then please contact a professional,
as these speakers are heavy. 
Due to the comprehensive fixing points the 
AELITEOn Wallscan be
mounted vertically or horizontally, which makes them ideal for
placement around screens for AV use. Closeness to room boundaries
has a major impact on the low frequency performance. This effect is
relied upon to correctly balance the response of the speaker.
When using your speakers with a suitable AV amplifier/processor
and Subwoofer (such as the 
AELITESub), it is advisable to set the
speaker’s size to ‘small’ as this will the correctly feed the low audio
information through the subwoofer giving you an improved power
response and better blended sound from your system. If the filter
point is variable it should be set to 80Hz
Positioning Introduction 
						

							Bi-amping
Bi-amping adds a second amplifier to the system. One power
amplifier drives the treble section of both loudspeakers; a second
drives the mid/bass sections. 
Note that the shorting links must be
removed. Failure to do so will result in damaging the amplifiers.
As regards the loudspeakers, wiring for bi-amping is achieved in
much the same way as bi-wiring. Treble amplifier positive (red)
terminals should be connected via the ribbed cable to the positive
(red) HF terminal on the speaker. Similarly, treble amplifier negative
is connected to the negative (black) HF terminal on the speaker.
Repeat this process with the mid/bass amplifier and LF terminal
pair.
After wiring up 
Lower the volume to the minimum, switch on the amplifier, select
the signal source and then raise the volume to the listening level
required. 
Warning
Check that your amplifier is switched off before installing your
loudspeakers. Failure to do so may result in speaker or amplifier
damage.
Conventional
Normal passive wiring requires shorting links to be in place
between the treble and mid/bass sections. The positive (ribbed)
cable from the amplifier positive (or red) terminal should connect
with the positive (red) terminal on the loudspeaker. Similarly the
negative (smooth) cable should connect the amplifier negative
terminal (black) to the negative terminal (black) on the
loudspeaker.
Bi-wiring
Bi-wiring separates the bass and treble ground paths in the
loudspeaker and offers sound quality advantages. An extra set of
cables is required. Note that the shorting links are removed
between the treble and mid/bass sections and should be stored for
later use if conventional, passive driving is required.
Two pairs of cables are connected to the amplifier terminals. One
cable of each pair should connect to the treble section and one to
the mid/bass section. The positive (ribbed) cables from the
amplifier positive (or red) terminal should connect with the positive
(red) terminals on the loudspeaker. Similarly the negative (smooth)
cables in each pair should connect the amplifier negative terminal
(black) to the negative terminals (black) on the loudspeaker.
Connection 
						

							HF unitNeodymium tweeter with high
dispersion diaphragm.
Ferrofluid cooled and damped.
Magnetically shielded.
Exclusively profiled. 
LF unit Twin 110mm units featuring die-cast
chassis. Lightweight alloy cones with
32mm coils. High-power, long-throw
magnet systems. Magnetically
shielded.
[email protected], 3rdorder, high power
Power Handling175W max (undistorted program
drive)
Frequency response  ±3dB80Hz to 23kHz  (on wall)
Frequency response  ±6dB68Hz to 21kHz (on wall)
Sensitivity 90 dB/W
Impedance6 ohm (4 ohm minimum)
Cabinet Sealed, high absorbency, low
resonance enclosure with real wood
veneered front baffle (except silver
version).
Te r minalsGold-plated 4-way binding posts.
Weight(excl. packaging) 7kg
Dimensions(WxHxD) 186 x 530 x 110 mm
Your Acoustic Energy loudspeakers are guaranteed against original defects
in materials, manufacture and workmanship for 3 years from the date of
purchase. Please retain all original packaging materials for possible future
use. We suggest that you complete details of purchase now and keep this
information in a safe place for future reference.
Under this warranty Acoustic Energy agrees to repair any defect or, at the
company’s discretion, replace the faulty component(s) without charge for
parts or labour. This warranty does not imply any acceptance by Acoustic
Energy or its agents for consequential loss or damage and specifically
excludes fair wear and tear, accident, misuse or unauthorised
modification.
This warranty is applicable in the United Kingdom only and does not in
any way limit the customer’s legal rights. Claims and enquiries under the
warranty for AE products purchased outside the UK should be addressed
to the local importers or distributors.
If you have reason to claim under the warranty please contact your dealer
in the first instance.
Your Name:  .........................................................................................................
Your Address:.........................................................................................................
...............................................................................................................................
Dealer’s Name:  ....................................................................................................
Serial Numbers: .......................................Date of Purchase: ................................
Acoustic Energy Limited
16 Bridge Road, Cirencester
Gloucestershire GL7 1NJ
Tel +44(0)1285 654432
Fax +44(0)1285 654430
Web www.acoustic-energy.co.uk
SpecificationsWarranty