Adam Equipment MDW Physician Scales MDW300LREVA2 User Manual

							Page 1 
 
Adam Equipment 
     
 
 
 
MDW – 300L
 
HEALTH AND FITNESS SCALE with BMI 
 
 
 
 
 
 
   
ADAM EQUIPMENT CO. LTD.   
p.n. 700660159 Rev. A2, Apr 2014 
      
						

							Page 2 
   
CONTENTS    
1.0 INTRODUCTION ...................................... ..................................................... 3 
2.0 TECHNICAL SPECIFICATIONS .......................... ......................................... 3 
3.0 DISPLAY AND KEY DESCRIPTIONS ...................... .................................... 4 
4.0 SETTING UP THE SCALE ............................................................................ 5 
5.0 FUNCTION ................................................................................................... 7 
5.1 WEIGHING .......................................... ...................................................... 7 
5.2 MEASURING HEIGHT .................................. ............................................ 8 
5.3 MEASURING BODY MASS INDEX (BMI) ................... .............................. 8 
6.0 CALIBRATION .............................................................................................. 9 
7.0 USER PARAMETERS ................................... ............................................. 10 
8.0 RS232 COMMUNICATIONS .............................. ......................................... 11 
9.0 ERROR MESSAGES .................................................................................. 15 
10.0 WARNING ................................................................................................... 15 
WARRANTY INFORMATION .............................. .................................................. 17 
 
    
						

							Page 3 
1.0  INTRODUCTION 
   
·   The MDW 300L scale is a Digital Health and Fitness  Scale with Body Mass 
Index (BMI) readout. 
  
·  It is an accurate electronic device with advanced  design and stable 
performance. 
 
·  It is designed to measure both the weight and the  height of a person and 
compute the BMI index.  
     
2.0  TECHNICAL SPECIFICATIONS 
    
Maximum capacity  300 kg / 660lb 
Minimum capacity  2 kg / 4lb 
Scale division  0.05kg / 0.1lb 
Height range  60 cm-212 cm / 24”-83” 
Division of measurement 
(height used in BMI calculation) 
entry via keypad 1cm / 0.5” 
Division of measurement 
(height measurement) 0.1cm / ⅛” 
Display  LED  display 
Size of platform  375 X 275 mm 
14.75” X 10.8” 
Overall dimension, height  
pillar in lowest position 570 X 275 X 1310 mm 
22.4” X 10.8” X 51.5” 
Net weight  13 kg / 29 lb. 
Environment for Use  Temperature: 5ºC-40ºC;  Humidity: 
						

							Page 4 
3.0  DISPLAY AND KEY DESCRIPTIONS 
  
   
KEYS FUNCTIONS 
[On/Off / 
Zero]  To turn the scale on or off.  
To zero the scale if the display drifts from zero. 
[Tare] 
¿
¿¿
¿
  To tare the scale, if necessary. Accept settings as
 required 
[Units / 
BMI] 





  To toggle the weighing unit between Kg and Lb. and 
to select the BMI 
function.   Move active digit to the right when req uired. 
[Print / 
Hold] 

  To lock the reading even if the person to be weighe
d is moving and 
also to print the weight via the RS232 interface. I ncrease value or 
settings when required. 
 
DISPLAY DESCRIPTIONS 
Kg Indicates when the scale is weighing in Kilograms. 
Lb Indicates when the scale is weighing in Pounds. 
Hold Indicates  when  the  scale  has  held  the  weight  readin g  shown  on  the 
display. It will flash until it locks into the stab le reading when it will then 
remain on for a preset time when it has held the di splayed reading. 
BMI Indicates when the scale is displaying the Body Mas s Index value. 
CH The charge light will be on when the battery is recharging. 
AC 
 This indicates when the scale is being used with th
e AC adapter. 
ZERO This indicator will be displayed in the left corner  when the scale reaches 
zero. 
NET The Net weight is displayed, Tare weight is at zero . 
     
						

							Page 5 
4.0 SETTING UP THE SCALE  
   
·  Take the scale out of the box.  
 
 
  
 
  
1. Locate the 4 screws (2)    
2. Place the cable (4) through the pillar 
(3).  
3. Insert the 4 screws (2) through the 
holes on the pillar bracket and secure 
the bracket to the indicator (1),   
4. Make sure the screws are securely 
tightened. 
     
5. Place the cable (4) into the tube 
support (6) on the scale base.  
6. Insert the pillar (3) into the tube 
support (6).  
7. Rotate the pillar to position the 
indicator (1) in the direction desired, 
and then secure using the 2 screws 
(5) into the fixing tube (6).  
8. Locate the load cell cable (13) ready for 
connection     
						

							Page 6 
 
   
 
 
  
9. Place the indicator cable (4) and the  
load cell cable (13) together near the hole 
on the base (16).  
10. Plug the two connectors (15) together.   
11. Position the connector inside the base 
(16).  
12. The cables should be fixed to the base 
using the clip provided (14).  
13. Locate the fixing bolt and washer 
(10) used to secure the height rod to 
the scale base (11)  
14. Locate the height rod (7) onto the 
fixing points (9) of the upper and lower 
brackets (8) & (12).  
15. Secure the bolt and washer to the 
bracket on the base (10)    
16. Tighten the bolt on the upper 
bracket (9).      
						

							Page 7 
5.0  FUNCTION 
 
5.1  WEIGHING 
 ·  Place the Scale on an even floor and press the  [On/Off] key.  
 
·  The instrument performs a self-test after which it  is ready for operation.  
 
·  Press the  [On/Off] key and the machine switches off.  
 
·  The  person to be  weighed  can  step  on  to  the  platfo rm once  the  scale  shows 
0.0  on  the  display.  The  weight  will  be  display  in  K g.  or  lb.  depending  on  the 
units chosen by the user.  
 
·  If  the  weighing  value  is  to  be  tared  press  the  tar e  key  to  remove  the  weight 
value from the display. 
 
·  Press the  [Units] key for changing the weighing unit to kg or lb. Th e LED will 
indicate the chosen weighing unit. 
 
·  Overload display : When “
FULL” appears on the display, it shows that the load 
on the platform is over the maximum capacity. Under  these circumstances, it 
is  necessary  to  reduce  the  load  otherwise  the  senso r  or  the  platform  will  be 
damaged. 
   
·  Hold  Function:  To  lock  the  weighing  result,  press  the  [Print/Hold] key.  The 
LED will flash until a stable reading has been obta ined and then it will light up 
constantly.  The  weight  will  be  displayed  until  the  hold  time  has  expired  (see 
Sec 7.0) or to manually release the function, press  the [Print/Hold]  key again. 
  
·  Print Function:  To send the weighing result to a printer or comput er press the 
[Print/Hold]  key when the  [Print/Hold] key has been set up in the parameter 
section to work as print function. 
    
						

							Page 8 
5.2  MEASURING HEIGHT  
 ·  To measure someones height, it is necessary to ext ract the measuring rod and 
place the height arm on top of the head of the pers on being measured.   
 
·  For shorter heights the height arm can be released  by pressing the red button 
on  the  top  of  the  height  rod,  and  then  moving  the  h eight  arm  to  the  lower 
section of the height pillar.  
 
·  The height is read on the bar at the top of the su pport.  The height can be read 
in either centimetres or inches,  
   
5.3  MEASURING BODY MASS INDEX (BMI)   
 
·  Once the height has been determined it is possible  to enter the height reading 
into the display ready for the scale to compute the  BMI.  
 
·  Press  and  hold  the  [Unit/BMI]  key  to  enter  the  BMI  mode.    The  display  will 
show  the  last  height  value  used,  “ Cm123”  or  “In123”  depending  on  which 
weighing unit you are currently using. 
  ·   The height entry unit (Cm or In) will be flashing  to show you which unit you are 
currently in, use the Up arrow key to change the he ight entry unit between Cm 
to In as required 
 
·  Enter your height using the arrow keys, the  [Print/Hold] /
 key  will increment 
the flashing digit, the right arrow, the  [Unit/BMI] /

 key, will move the flashing 
digit to the adjacent digit. 
 
·  Press the  [Tare]/¿
¿¿
¿
 key to confirm the value. 
 
·  The display  will  now  show  the  BMI  based  on  the  cur rent  weight  on the  scale 
and the height entered. 
 
·  Press the  [Unit/BMI] key to exit the BMI mode and return to normal weig hing.  
 
·  The Hold function will work as described above whi lst in the BMI mode. 
  
    
						

							Page 9 
6.0  CALIBRATION 
  
Before calibrating the scale, you should ensure that you have a suitable known weight for 
calibration.    
1.  When in normal weighing mode with the scale at zero  press and hold down [TARE] and 
[ON / OFF]  keys to enter the calibration mode.  
  
2.  If  the  calibration  switch  is  in  the  off  position  on   the  main  PCB  inside  the  scale,  the 
indicator  will  show  “ CAL.OFF”  and  then  exit  this  mode.  If  the  indicator  shows  “ CAL-? ”, 
the scale is ready for calibration. 
 
3.  When the indicator shows “C AL-?”, press the  [TARE] key to confirm and go to next step, 
or press the  [ON / OFF] key to exit the calibration mode.  
 
4.  When  ‘ 0.0’  is  displayed  the  scale  will  begin  to  calibrate  th e  scale’s  zero-point.  Ensure 
that there is no load or weight on the scale’s plat form. Press the [TARE] key to confirm, 
or press the  [ON / OFF] key to exit this mode.  
 
5.  A  few  seconds  after  the  [TARE] key  has  been  pressed  in  step  4  the  scale  will  show 
“300.0” and the kg LED, or “600.0” and the lb LED d epending on which unit you chosen, 
this is the default calibration weight from the fac tory. Press the [UNIT] key to select the 
calibration weight unit that you want to calibrate  in. Press the [ON / OFF] key to exit the 
calibration  mode  at  this  point  or  press  the  [Print/Hold] key  to  choose  a  different 
calibration  weight  value  (50kg,  100kg,  150kg,  200kg ,  250kg,  300kg  or  100lb,  200lb, 
300lb,  400lb,  500lb,  600lb);  Then  put  on  the  weight   that  you  selected  and  press  the 
[TARE]  key  to  confirm  the  chosen  standard  weight  that  was  selected  earlier.  The 
displayed data will flash on the display and if the  scale accepts the calibration data it will 
calculate and store the information into the EEPROM . If an error has occurred, the scale 
will display “CAL. Er” and return back to step 4 fo r re-calibration. If the loaded weight is 
not within the range of 95% to 105% of the weight v alue you selected, the scale will not 
calibrate but display “CAL. Er” and return back to  step 4 for re-calibration. ) 
 
6.  Check the calibration by putting the weight that yo u calibrated at back on the scale, if it 
is off repeat the calibration process again. 
  
    
						

							Page 10 
7.0  USER PARAMETERS 
  
This indicator has 4 parameter settings that can be selected. 
 
1. When  the  scale  is  in  normal  weighing  mode, press  an d  hold  down  the [ON  /  OFF] key 
and the  [UNIT] key for 3 seconds until ‘ Setup’ is shown on the display.  
 
2. When in the SETUP mode, press the  [Print/Hold] key to change the flashing digits, and  
[TARE]  key to confirm the flashing digits and move to the  next parameter setting. Press 
the  [ON / OFF]  key to exit the set up mode.  
  
3. Parameters setting summary: 
    
    Parameter  x/xy  Factory Set
 Setting 
A.o.t.  00-15  05 
Auto-off time:   
No auto-off = 00.                                  
           
01-15 minutes auto-off time.  
P.H.  0,1,2  1  0 = Only Print Function  
1 = Only Hold Function 
2 = both HOLD and PRINT function (pressed 
down less 3s,this key works as Print 
function; pressed down more than 3s,this 
key works as HOLD function) 
H.t  0-4  0  Hold time:  
0 = no time limit. 
1 = 10 seconds 
2 = 30 seconds 
3 = 60 seconds 
4 = 120 seconds 
S.F.  0-3  0  0 = No RS232 Function.  
1 = Continuously outputs display data.  
2 = Output display data when PRINT pressed 
3 = Bi-directional communication (the scale 
receives and executes commands  from the 
HOST device)