ADDER ePower Switch 8 Master Manual

 
50 Number of unsuccessful Requests before Action: 
In this field, define the number of Ping commands to be sent to the IP device before executing the actions. 
The number can be set between 1 and 65535 seconds. 
Delay before First Request after Power up: 
In this field, define the time in seconds before restarting the monitoring after the reboot action. 
The delay can be set between 30 and 65535 seconds. 
 
Configuring the Actions: 
 
For the Event defined above, you can choose and configure following...

51  LOGOUT: 
Click Logout at the bottom of the page to exit the session without saving changes. 
DISCARD CHANGES: 
Click Discard Changes at the bottom of the page to discard all the changes you have made on this page. 
APPLY CHANGES: 
Click Apply Changes at the bottom of the page to save changes. 
   

 
3.3.9.3. S
 
This rule 
c
Telnet, SM
running the
device off 
 
 
Rule ID: 
The ePo
w
used to ide
middle of t
Rule Nam
In this field
and can co
Rule Colo
In this field
use own c
identify the
Rule Type
In this drop
 
Configuri
 
IP device 
In this fiel
d
the Port to
The value 
Wait Tim
e
In this field
The delay 
 
Settings / R
can be used t
MTP, POP...)
ere. If the co
and, after a 
werSwitch 8X
entify rules s
the Rule list, 
me: 
d, enter the 
ontain alphan
or: 
d, select one
colours, just t
e triggered...

53  Interval between Requests: 
In this field, define the delay between the scan commands sent to the IP device. The delay can be set 
between 30 and 65535 seconds. 
Number of unsuccessful Scan Commands before Action: 
In this field, define the number of Port scanning commands to be sent to the IP device before executing 
the actions. 
The number can be set between 1 and 65535 seconds. 
 
Delay before First Request after Power Up: 
In this field, define the time in seconds before restarting the...

 
54 Syslog / Trap / Mail Message: 
This field appears only if you have already specified at least one destination Syslog Server 
(Misc/Log Settings Page), one destination SNMP Server (General/SNMP Page) or a destination 
SMTP Server (General/SMTP Page). 
Up to 255 characters may be entered in this free text field. The text will appear in the Syslog, the Trap and 
the e-mails.  
 
LOGOUT: 
Click Logout at the bottom of the page to exit the session without saving changes. 
DISCARD CHANGES: 
Click Discard...

55 
3.3.9.4. S
 
This rule 
c
power sup
 
Rule ID: 
The ePo
w
used to ide
middle of t
Rule Nam
In this field
and can co
Rule Colo
In this field
use own c
identify the
Rule Type
In this dro
perform. 
 
 
Configuri
 
Power In
p
In the first 
Each devi
c
• M0 for
• S1 to S
• DIM1 t
 
Settings / R
can be used
pplies of conn
werSwitch 8X
entify rules s
the Rule list, 
me: 
d, enter the 
ontain alphan
or: 
d, select one
colours, just t
e triggered ru
e: 
p-down list, 
ng the Eve
n
put to monit
Drop-Down 
ce...

 
56 A character between brackets can follow this ID Code: 
- The X character means that the corresponding peripheral is physically not connected. 
- The ! character means that the corresponding peripheral is physically connected but not activated.  
   If you want to activate it, go to the Settings/Power Outlets tab. 
- The   character (blank) means that the corresponding satellite is physically connected and activated. 
In the second Drop-Down list, choose the power input (Input A or Input B) you wish...

57  Syslog / Trap / Mail Message: 
This field appears only if you have already specified at least one destination Syslog Server 
(Misc/Log Settings Page), one destination SNMP Server (General/SNMP Page) or a destination 
SMTP Server (General/SMTP Page). 
Up to 255 characters may be entered in this free text field. The text will appear in the Syslog, the Trap and 
the e-mails.  
The message can be completed with the status of an input (a power supply or door contact for example) 
or the value of a sensor...

 
3.3.9.5. S
 
This rule 
c
proximity s
 
Rule ID: 
The ePo
w
used to ide
middle of t
Rule Nam
In this field
and can co
Rule Colo
In this field
use own c
identify the
Rule Type
In this dro
perform.  
 
Configuri
 
Digital In
p
In the first 
• M0 fo
r
• TP foll
• DIM fo
• PB fol
 
Settings / R
can be used
sensor, a pus
werSwitch 8X
entify rules s
the Rule list, 
me: 
d, enter the 
ontain alphan
or: 
d, select one
colours, just t
e triggered ru
e: 
op-down list, 
ng the Eve
n
put to monit
drop-down l
r...

59  In the second drop-down list, choose the Input you want to monitor. The ePowerSwitch 8XM uses ID 
Codes to clearly identify each Input:  
• DI1 to DI4 for the digital inputs of the ePowerSwitch 8XM,  
• PS followed by a number for the IR  proximity sensor inputs, 
• DI followed by a number for the digital inputs of a DIM module, 
• SP followed by a number for a short push on the push buttons, 
• LP followed by a number for a long push on the push buttons. 
 
 
Action if contact...: 
In this Drop-Down...