ADDER SmartView MultiScreen VGA KVM Switch Manual

SmartView MultiscreenInstallation and UsePage 10Figure 2b - SmartView Multiscreen rear view (Model SVMS4-Dual)Figure 2c - SmartView Multiscreen rear view (Model SVMS2-Quad) 

SmartView MultiscreenInstallation and UsePage 11Figure 2d - SmartView Multiscreen rear view (Model SVMS2-Dual)Figure 3 - Remote control pad / display (optional accessory - part RC1) 

SmartView MultiscreenInstallation and UsePage 122. Installation2.1 What you will need  Cables to connect the SmartView Multiscreen to each of your PC keyboard, video
and mouse ports. Cable specifications are given in appendix A. For convenience we
suggest that you connect your keyboard, mouse and first video port using an Adder
3-in-1 combination cable. Additional video ports may then be connected using video-
only cables. Monitors with standard VGA/SVGA (15 pin) connectors that will work when
connected...

SmartView MultiscreenInstallation and UsePage 132.2 Mounting the SmartView Multiscreen
The SmartView Multiscreen has been designed for use on a desktop or shelf in
close proximity to the user’s monitor and peripherals. The optional remote controller
may be used if you wish to locate the SmartView Multiscreen on a desk or shelf that
is some distance from the monitor and peripherals.
2.3 Connecting your devices
Ensure that the optional power adapter is disconnected from the SmartView
Multiscreen and that...

SmartView MultiscreenInstallation and UsePage 14to the mouse and/or keyboard not being recognised by the computers when they are
switched on.
2.4 ‘Interface powered’ operation without the optional power
       adapter
The SmartView Multiscreen draws its power from the connected computers via the
keyboard cables. A single keyboard connection is normally sufficient to power the
SmartView Multiscreen provided that the cable is no longer than 5 metres. If more
than one computer is connected then the power...

SmartView MultiscreenInstallation and UsePage 15To enter configure mode at power on:
Switch off all the attached PCs and the SmartView Multiscreen. Hold down the front
panel key whilst powering on the SmartView Multiscreen. Remember that the
SmartView Multiscreen draws its power from any attached PC via the keyboard
cable and so will power itself on when the attached PC is switched on or when the
optional power adapter is connected. Do not release the key until the SmartView
Multiscreen displays C to...

SmartView MultiscreenInstallation and UsePage 16L1 - SmartView Multiscreen locks on to active ports only during autoscanning
(default)
L2 - SmartView Multiscreen locks on to every port during autoscanning
L3 - SmartView Multiscreen powers on in autoscan mode and locks on to active
ports only
L4 - SmartView Multiscreen powers on in autoscan mode and locks on to all ports
L5 – Allow the mouse to run at any speed (default)
L6 – Dont allow the mouse to run at very slow speeds
L7 - Cascade query code = AD...

SmartView MultiscreenInstallation and UsePage 17U7 – Cycle between all ports when switching with ‘Hotkeys + Tab’ or three button
mouse (default)
U8 – Cycle between active ports only when switching with ‘Hotkeys + Tab’ or three
button mouse
H1 - Hotkey combination is CTRL + ALT + command key  (default)
H2 - Hotkey combination is CTRL + SHIFT + command key
H3 - Hotkey combination is ALT + SHIFT + command key
H4 - Hotkey combination is RIGHT ALT + command key
H5 - Hotkey combination is LEFT ALT + RIGHT ALT...

SmartView MultiscreenInstallation and UsePage 182.9 Other useful installation information
PC boot up sequence - When your PCs are powered on they communicate with
any attached keyboards and mice and setup parameters required by the particular
operating system. It is necessary for the SmartView Multiscreen to be attached and
powered on during this sequence so that it can give the required responses and
keep track of all the modes and settings requested by each of the connected PCs.
Mouse characteristics -...

SmartView MultiscreenInstallation and UsePage 19Multiscreen, press the front panel key again. A complete power off reset of the
connected keyboards and mice will then be performed. This function only resets the
shared keyboard and mice that are plugged into the control port. It does not affect
the status of any of the other ports on the switch or the CPU connections.
2.11 Hot plugging the SmartView Multiscreen into running systems
and re-enabling disconnected CPU PS/2 mouse connections
It is advisable to...