Addonics Technologies BluRay DVD CD DigiCopier DGBRC7 User Manual

							Technical Support
If you need any assistance to get your unit functioning properly, please have your 
product information ready and contact Addonics Technical Support at:
Hours: 8:30 am - 6:00 pm PST
Phone: 408-453-6212
Email: http://www.addonics.com/support/query/
www.addonics.com
User Guide
1:7 Blu-Ray/DVD Digicopier
(DGBRC7)
T E C H N O L O G I E S         
						

							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
DigiCopier Overview
 
There  are four buttons  and an LCD  on the panel  of DigiCopier.
1  –  LCD s hows a funct ion or a mess age.
2  –  it  is  used t o s c roll  up f unct ion menus.
3  –  it  is  used t o s c roll  down f unction menus .
4  –  it  is  used t o e xe cu te  a  funct ion.
5  –  it  is  used t o canc el a function.Duplicat or Panel
EN T
ESC
2
3 4
5
1
C
onnecting  th e power  cable a nd  tu rning on t he D igiC opier
a. Connect the  power cord prov ided f rom the wall  outlet to  the  back  of the  DigiCopier.
b. A  main  power s witch is  loc ated  at the  back  of the t ower. T urn t he swit ch on.  A not her 
aux iliary  power s witch is  loc ated  on t he front  of the t ower.
Step s f o r t h e C opy ing Pr ocess
Note: may not able to copy protected Blu-ray, DVD or CD.
Step 1 Turn on the DigiCopier  by  pres sing t he aux iliary  power  switch.
Step 2 I nsert media y ou wis h to  duplicat e int o the  source t ray 
on t he top. 
Step 3 Insert up to eleven Blu-Ray, DVD, or CD recordable media 
into the target drives.
Step 4 After the Blu-ray or DVD-ROM and DVD writers detect media, press ENT button to 
start copying.  
C opy-DV D         0 %
4213. 4MB         7:30
LCD will show t he copy ing informat ion as follows .
W hen  copying  is in  progress,  MB and  time  will decreas e while  the  percent age of  complet ion will 
increase. “MB” means the  size o f dat a that you  want to copy .
W hen  copying  comes to  an  end,  LCD  will show  the  results  as follows.  T he  DVDs  that  were 
successf ully copied  will eject  automat ic ally .  
Copy
O K:  07
Duplicator Panel
Targets Source 
						

							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
Duplicator FunctionsThe duplicator has six menu sections: The Main menu, Image, Edit Track, Lightscribe, Setup 
Options and Advanced Setup. Advanced Setup Options is accessed through the Main menu. 
Advanced Setup is accessed by holding the ESC button from any other menu\
 until the unit 
beeps.
1. Copy
Copies from the source to the target drives. Rewritable media may be use\
d for targets; 
however, all existing data will be erased before proceeding with the copy opera\
tion. Insert all 
discs and wait for the drives to settle before pressing ENT. When complete, elapsed time will 
be displayed as well as the number of OK copies made. Discs copied OK wi\
ll be ejected 
automatically.
2. Test
Simulates copy process. Function is identical to Copy without actually w\
riting source data to 
target discs. Rewritable media may be used; however, all data will be erased before Test 
process proceeds with simulation. Testing is not supported for DVD+R media.
3. Test & Copy
Performs Test function followed by Copy function. Testing is not supported for DVD+R media.
4. Verify
Confirms all target discs are readable.
5. Compare
Confirms all data on target discs as identical to source disc. Results a\
re: OK for identical data, 
FAIL indicates target Table Of Contents does not match or too many mismatches occurred, 
and DIFF will show number of bytes that are different.
6. Prescan
Confirms source disc is entirely readable without error.
7. Disc Info
Detect and report disc type and capacity.
8. Select Source
Allows selection of source drive. Default is CH01, which is the top unit\
 on this duplicator. 
Selecting HDD is not supported on this duplicator. Leaving this set to CH01 is strongly 
recommended.
9. Image Menu
The Image feature is not supported with this duplicator.
10. Edit Track Menu
The Edit Track feature is used for collecting individual tracks from one or more a\
udio CDs and 
merging them to create target discs with the custom collection.
10-01. CD to CD Edit
Entering this function will display each track on the LCD, use arrow key\
s to change 
tracks, press ENT to select or deselect a track. Selected tracks will display a “+”\
. 
When all desired tracks are selected, use arrow keys until “End” a\
ppears then press 
ENT. After confirming the selection, the duplicator will burn the selected tr\
acks to the 
target media. When complete, press ENT and the duplicator will ask if you want to 
continue. Selecting “Yes” will eject the source disc and prompt for the next source, 
then return to track selection. Selecting “No” will respond with “\
Close all discs 
session?” to confirm finalizing target media. When target media sessi\
ons are closed, 
no further tracks may be added. If target media is not closed, more trac\
ks may be 
added later; however, the discs may not be playable on all CD players.
10-02. CD to HDD Edit
Creates a disk image on a Hard Disk with a collection of audio tracks fr\
om one or 
more Audio CDs. This feature is not supported on this duplicator.
10-03. Close Session
Manually closes the last session on target Audio CDs. Target media will no longer be 
able to add more tracks. Closing the final session on Audio CDs is recommended for 
best compatibility with audio CD players.
11. Lightscribe Menu
Lightscribe is a disc technology using the drives laser to create visib\
le images on specially 
coated discs. This feature requires connection of a hard disk and is not supported wit\
h this 
duplicator.
12. Setup Menu
Allows changes to the following default settings: 12-01. Language
Selects language used for menus.
12-02. Burn Speed
Sets the maximum speed for burning various target media. Default setting\
s are: 4X 
for Blu Ray, 16X for DVD, 32X for CD (data) and 16X for Audio CD.
12-03. Read Speed
  Sets the maximum speed for reading the source disc. Default is Maximum.
12-04. Auto Start Drive
When set to ON, duplicator will automatically begin the Copy function as\
 soon as a 
blank target media is detected. Default setting is OFF.
12-05. Startup Menu
Sets the menu that will appear after the duplicator is finished initiali\
zing after power 
up.
12-06. Auto Verify
When set to ON, the Copy function will be followed by a Verify function automatically 
to confirm the target media is readable. Default setting is OFF.
12-07. Auto Compare
When set to ON, the Copy function will be followed by a Compare function\
 automat
cally to confirm target media is identical to the source. Default settin\
g is OFF.
12-08. Auto Prescan
When set to ON, the Copy function will start with a Prescan Source funct\
ion to 
confirm the source media is completely readable without errors. Default \
setting is 
OFF.
12-09. Eject Disc
Sets the eject behavior of drive trays after targets finish burning. Eje\
ct Good Only will 
eject discs that are considered OK, discs considered to have failed to c\
opy correctly 
are not ejected. Eject All Disc will eject all discs regardless of copy success, and Do 
Not Eject will not eject any discs. Default setting is Eject Good Only.
12-10. Burn On The Fly
When set to On, data will be copied directly from the source disc to tar\
get media. 
When set to OFF, a temporary image file will be created on a hard disc before burning 
target media, then discarded after the process is complete. Default sett\
ing is ON. 
Setting Burn On The Fly to OFF is not supported with this duplicator. 
						

							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
 
Duplicator FunctionsThe duplicator has six menu sections: The Main menu, Image, Edit Track, Lightscribe, Setup 
Options and Advanced Setup. Advanced Setup Options is accessed through the Main menu. 
Advanced Setup is accessed by holding the ESC button from any other menu\
 until the unit 
beeps.
1. Copy
Copies from the source to the target drives. Rewritable media may be use\
d for targets; 
however, all existing data will be erased before proceeding with the copy opera\
tion. Insert all 
discs and wait for the drives to settle before pressing ENT. When complete, elapsed time will 
be displayed as well as the number of OK copies made. Discs copied OK wi\
ll be ejected 
automatically.
2. Test
Simulates copy process. Function is identical to Copy without actually w\
riting source data to 
target discs. Rewritable media may be used; however, all data will be erased before Test 
process proceeds with simulation. Testing is not supported for DVD+R media.
3. Test & Copy
Performs Test function followed by Copy function. Testing is not supported for DVD+R media.
4. Verify
Confirms all target discs are readable.
5. Compare
Confirms all data on target discs as identical to source disc. Results a\
re: OK for identical data, 
FAIL indicates target Table Of Contents does not match or too many mismatches occurred, 
and DIFF will show number of bytes that are different.
6. Prescan
Confirms source disc is entirely readable without error.
7. Disc Info
Detect and report disc type and capacity.
8. Select Source
Allows selection of source drive. Default is CH01, which is the top unit\
 on this duplicator. 
Selecting HDD is not supported on this duplicator. Leaving this set to CH01 is strongly 
recommended.
9. Image Menu
The Image feature is not supported with this duplicator.
10. Edit Track Menu
The Edit Track feature is used for collecting individual tracks from one or more a\
udio CDs and 
merging them to create target discs with the custom collection.
10-01. CD to CD Edit
Entering this function will display each track on the LCD, use arrow key\
s to change 
tracks, press ENT to select or deselect a track. Selected tracks will display a “+”\
. 
When all desired tracks are selected, use arrow keys until “End” a\
ppears then press 
ENT. After confirming the selection, the duplicator will burn the selected tr\
acks to the 
target media. When complete, press ENT and the duplicator will ask if you want to 
continue. Selecting “Yes” will eject the source disc and prompt for the next source, 
then return to track selection. Selecting “No” will respond with “\
Close all discs 
session?” to confirm finalizing target media. When target media sessi\
ons are closed, 
no further tracks may be added. If target media is not closed, more trac\
ks may be 
added later; however, the discs may not be playable on all CD players.
10-02. CD to HDD Edit
Creates a disk image on a Hard Disk with a collection of audio tracks fr\
om one or 
more Audio CDs. This feature is not supported on this duplicator.
10-03. Close Session
Manually closes the last session on target Audio CDs. Target media will no longer be 
able to add more tracks. Closing the final session on Audio CDs is recommended for 
best compatibility with audio CD players.
11. Lightscribe Menu
Lightscribe is a disc technology using the drives laser to create visib\
le images on specially 
coated discs. This feature requires connection of a hard disk and is not supported wit\
h this 
duplicator.
12. Setup Menu
Allows changes to the following default settings: 12-01. Language
Selects language used for menus.
12-02. Burn Speed
Sets the maximum speed for burning various target media. Default setting\
s are: 4X 
for Blu Ray, 16X for DVD, 32X for CD (data) and 16X for Audio CD.
12-03. Read Speed
  Sets the maximum speed for reading the source disc. Default is Maximum.
12-04. Auto Start Drive
When set to ON, duplicator will automatically begin the Copy function as\
 soon as a 
blank target media is detected. Default setting is OFF.
12-05. Startup Menu
Sets the menu that will appear after the duplicator is finished initiali\
zing after power 
up.
12-06. Auto Verify
When set to ON, the Copy function will be followed by a Verify function automatically 
to confirm the target media is readable. Default setting is OFF.
12-07. Auto Compare
When set to ON, the Copy function will be followed by a Compare function\
 automat
cally to confirm target media is identical to the source. Default settin\
g is OFF.
12-08. Auto Prescan
When set to ON, the Copy function will start with a Prescan Source funct\
ion to 
confirm the source media is completely readable without errors. Default \
setting is 
OFF.
12-09. Eject Disc
Sets the eject behavior of drive trays after targets finish burning. Eje\
ct Good Only will 
eject discs that are considered OK, discs considered to have failed to c\
opy correctly 
are not ejected. Eject All Disc will eject all discs regardless of copy success, and Do 
Not Eject will not eject any discs. Default setting is Eject Good Only.
12-10. Burn On The Fly
When set to On, data will be copied directly from the source disc to tar\
get media. 
When set to OFF, a temporary image file will be created on a hard disc before burning 
target media, then discarded after the process is complete. Default sett\
ing is ON. 
Setting Burn On The Fly to OFF is not supported with this duplicator. 
						

							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
12-11 Burn Mode
Sets style of burning for Audio CDs. DAO (Disc At Once) burns the entire media without 
stopping. TAO (Track At Once) burns each audio track individually. Default setting is DAO.
12-12. Display Time
When set to ON, unit will display a timer during copy operations. Defaul\
t setting is ON.
12-13. Button Sound
When set to ON, unit will emit a beep sound whenever keys are pressed. D\
efault setting is 
ON.
12-14. Device Info
Displays details about each drive unit.
12-15. System Info
Displays details about the duplicator.
12-16. Quick Erase
Erases file system on all rewritable media detected.
12-17. Full Erase
Erases all data on all rewritable media detected.
12-18. Auto Close Tray
Allows trays to be closed automatically after a set time when Copy or Test functions are 
selected. Default setting is OFF.
12-19. Quick Compare
Controls behavior of the Compare function. When set to a numerical size,\
 only that much data 
will be compared before the unit considers a compare OK. Default setting\
 is OFF for full 
comparison.
12-20. Link Mode Select
Allows multiple duplicators to be connected together to copy more target\
s from a single 
source. This feature is not supported for this duplicator.
12-21. Re-scan
Rescans all ports for drives with media inserted.
12-22. Tray-In/Out
Controls behavior of ejecting drives. Default setting is All Once.
12-23. Boot Time Delay
Sets delay in seconds during initialization to allow drives to settle. D\
efault setting is 5 
seconds.
12-24. Start Tray Eject
When set to ON, all drives will be ejected during initialization after p\
ower up. Default setting is 
ON.
12-25. Disc Redetect
When set to ON, the duplicator will retry once if an error occurs during\
 disc detection. This 
feature is used for low quality media. Default setting is OFF.
12-26. Show Burn Speed
When set to ON, burn speed will be displayed during copy process. Defaul\
t setting is ON. 
						

							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
13. Advanced Setup Menu
Allows changes to advanced default settings. Making changes to these set\
tings is not 
recommended.
13-01. UnderRun Protect
When set to ON, duplicator will protect against buffer underrun conditions while 
burning targets. Default setting is ON.
13-02. Overburn
When set to ON, the duplicator will attempt to burn past physical limit \
of media for very 
full discs. Caution: enabling Overburn may cause hardware damage to the \
duplicator.
13-03. Read Error Skip
When set to ON, duplicator will ignore read errors while reading the sou\
rce disk during 
Copy function. Data written to targets for sectors that caused read erro\
rs will be 
unpredictable and the Compare function will show differences.
13-04. Format HDD
Prepares a hard disk for use with imaging and editing functions. This feature is not 
supported for this duplicator.
13-05. Verify HDD
Confirms a hard disk is properly prepared for use with the imaging and e\
diting 
functions. This feature is not supported for this duplicator.
13-06. Burn-in
Repeats one of three tests a set number of times, or indefinitely: Test function, Erase & 
Copy function (supports rewritable media only), and Compare function.
13-07. Update Firmware
Used to apply new firmware to the Duplicator subsystem. Insert a CD-RW disc 
containing the new firmware and press ENT. The duplicator will search for the correct 
file and apply it if found.
13-08. Compare Firmware
Used to confirm Duplicator subsystems firmware matches a file. Insert a\
 CD-RW disc 
containing the firmware and press ENT. The duplicator will search for the correct file 
and if found, compare its firmware against the file.
13-09. H/W Diagnostic
Performs a series of tests on the duplicator subsystem hardware.
13-10. Load Default
Changes all configuration settings to their default setting.
13-11. CD+G
When set to ON, enables copying of CD+G (Compact Disc + Graphics) form\
atted 
media. Default setting is OFF.
13-12. ISRC & MCN
When set to ON, duplicator will copy ISRC and MCN encoding for Audio CDs. Default 
setting is OFF.
13-13. USB Option
When set to ON, Main Menu Item 13 will become “USB Mode” and Advanced Setup 
will become Main Menu item 14. This feature is not supported for this duplicator. 
						

							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
13-16. Disc Counter
Shows a log of the number of copy operations performed, the number of di\
scs that 
have failed, and a counter for the number of discs burned and number of \
discs failed 
for each drive.
13-17. Auto Save Image
When set to ON, images of source media are automatically copied to a har\
d disk. 
This feature is not supported for this duplicator.
13-18. Update Drive F/W
Allows the duplicator to update a drives firmware. Burn drive firmware \
file onto CD 
media, insert into drive and press ENT. NOTE: this menu option only appears when 
compatible drives are installed.
13-19. F1 Hotkey Setup
Configures the F1 keys function. Note: this duplicator has no hotkeys a\
nd this 
function is not supported.
13-20. F2 Hotkey Setup
Configures the F2 keys function. Note: this duplicator has no hotkeys a\
nd this 
function is not supported.
13-21. Index
When set to ON, allows the duplicator to copy Index data. Default settin\
g is OFF.
 
13-22. AutoRun Time
Sets a delay in seconds before automatically starting a Copy process. De\
fault 
setting is 5 seconds. 
						

							www.addonics.com
Phone:   408-573-8580
Fax:     408-573-8588
Email:   http://www.addonics.com/sales/query/
CONTACT US