Home > Addonics Technologies > Removable Drive Syst > Addonics Technologies SnapIn Mobile Rack AESN4DA25 User Manual

Addonics Technologies SnapIn Mobile Rack AESN4DA25 User Manual

Add to Favourites
    Download as PDF Print this page Share this page

    Have a look at the manual Addonics Technologies SnapIn Mobile Rack AESN4DA25 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 299 Addonics Technologies manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    View all the pages
    Page
    of 4
    Add page 1 to Favourites
    image text
    Enable zoom 
    							www.addonics.com
Technical Support
If you need any assistance to get your unit functioning properly, please have your 
product information ready and contact Addonics Technical Support at:
Hours: 8:30 am - 6:00 pm PST
Phone: 408-453-6212
Email: http://www.addonics.com/support/query/
v6.1.11
T E C H N O L O G I E S
User Guide
2.5” Snap-In Disk Array
(AESN4DA25)
    Add page 2 to Favourites
    image text
    Enable zoom 
    							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
    Add page 3 to Favourites
    image text
    Enable zoom 
    							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
Installing the Snap-In Disk Array
1.   Slide the 2.5 Snap-In Disk Array into a standard 5.25” drive bays on your system or  
  storage chassis. 
2.   Secure the Snap-In Disk Array to the drive bay on both sides with the screws    
  provided. Note: using longer screws may interfere with the hard drive in\
stallation.
3.   Connect both 4-pin power connectors to the power supply and  the 4 SATA data 
  connectors to the SATA ports on the motherboard or SATA controller inside your 
 system.
4.    Power on your system. Check to make sure the main power LED is lit and t\
hat the  
  two cooling fans are spinning.
Adding and removing hard drives from the Snap-In Disk Array
1.  Be sure the lock on each drive door is in an unlock position. If not, us\
e the key that  
  comes with the Disk Array to unlock the drive door. Pull on the door lever to swing  
  open the drive door all the way.
2.  Slide a 2.5” SATA hard drive into the drive slot with the SATA connector side facing, 
  with the hard drive label facing up. The drive should slide all the way into the slot 
  with very little resistance. Forcing the drive into the slot will cause \
drive damage or 
  permanent damage to the Disk Array.
3.  Once the drive is all the way into the drive slot, close the door all th\
e way till the drive  
  door latch securely. This will engage power and data connection with the hard drive.  
  Lock the drive door with the provided key if desired. The drive LED should glow to 
  indicate the drive is inserted and powered up, and blink to indicate act\
ivity. NOTE: 
  the LED function is an optional feature to drives design and not all dr\
ives support the 
  LED. The LED may not light at all or glow steadily and never blink.
4.  To remove the hard drive from the Disk Array, unlock the drive door if needed then 
  gently pull the door open until the drive disengages from the internal c\
onnection, 
  then pull the drive out.
    Add page 4 to Favourites
    image text
    Enable zoom 
    							www.addonics.com
Phone:   408-573-8580
Fax:     408-573-8588
Email:   http://www.addonics.com/sales/query/
CONTACT US
    All Addonics Technologies manuals Comments (0)

    Related Manuals for Addonics Technologies SnapIn Mobile Rack AESN4DA25 User Manual