Addonics Technologies USB 31 or 39 dsaede User Manual

							 
 
 
 
 
 
 
Addonics 
T E C H N O L O G I E S 
 
 
 
 
Diamond ExDrive 
 
DSAEDES & DIEDES 
DSAEDEU & DIEDEU 
 
 
 
 
 
 
User’s Guide 
Version 1.0 
 
 
 
 
FCC Warning Statement  This equipment has been tested and found to comply with the limits for a class B digital device pursuant to Part 15 of the FCC rules.  These limits are designed to provide reasonable protection against harmful interference in a residential installation.  This equipment generates, uses and can radiate radio frequency energy.  If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications.  However, there is no guarantee that interference will not occur in a particular installation.  If the equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged to try and correct the interference by one or more of the following suggestions. Reorient or relocate the receiving antenna Increase the distance between the equipment and the receiver  Connect the equipment to a different power outlet other than the one where receiver is connected Consult a certified television or radio technician 
Hardware Installation Guide 
 
Step 1 
Use a Philips screwdriver to 
turn the cover securing 
screw into the “OPEN” 
position. 
 
 
 
 
 
 
 
 
 
Step 2 
Slide the aluminum cover 
towards the back end of the 
Diamond and remove it. 
 
 
 
 
 
 
 
 
 
 
 
 
Step 3 
 
For SATA Drive 
Carefully place the SATA hard drive 
with the label facing up into the 
Diamond enclosure.  Push the hard 
drive towards the back end to secure 
the drive connectors onto the 
Diamond enclosure’s SATA 
connector. 
 
 
 
 
 
 
 
 
        
						

							For IDE Drive 
Note: Set up your IDE hard drive 
as Master device 
 
Connect the 4-Pin Molex cable to 
the power connector on the IDE 
hard drive. Carefully place the IDE 
hard drive with the label facing up 
into the Diamond enclosure.  Push 
the hard drive towards the back end 
to secure the drive connectors onto 
the Diamond enclosure’s IDE 
connector. 
 
 
Step 4 
Turn the Diamond enclosure over 
with the hard drive  
mounting holes facing up. Use the 
included flat head  
screws to secure the hard drive 
onto the bottom of the 
enclosure and turn in the screw to 
the “LOCK” position. 
 
 
 
Cable Connections 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Power: Connect the 6-pin Mini DIN power cable (provided) to the 6-pin Mini DIN 
power connector located at the back of the enclosure. 
 
 
Data: 
Model: DSAEDES and DIEDES 
Connect the eSATA to eSATA cable to the eSATA connector located at the back 
of the enclosure and the other end of the eSATA cable to the eSATA connector 
on your SATA host controller with eSATA ports. 
 
Model: DSAEDEU and DIEDEU 
Connect the eSATA to eSATA cable to the eSATA connector located at the back 
of the enclosure and the other end of the eSATA cable to the eSATA connector 
on the USB2.0 to eSATA adapter. You can now plug the adapter to a USB port 
on your system. 
 
Powering On Enclosure: To power on the enclosure, move the switch located 
at the back of the enclosure to the ON mode. When the switch is turned on, the 
LED light beside it would light up to indicate power and also drive access. 
 
Note: There are no drivers needed to use the eSATA cable as long as the 
drivers are installed for the Serial ATA Controller card/chip. It is plug and 
play. 
 
 
Technical Support 
 
If you need assistance to get your unit functioning properly, please call Addonics 
Technical Support.  Our technical staff will be happy to assist you, but they will 
need your help to do so.  Calling the technical support staff without all the proper 
information can be both time consuming and frustrating.  Here are some tips to 
help you out: 
 
MODEL NUMBER – Please have this number on hand. 
SYSTEM INFORMATION – Type of computer, peripherals, etc. 
  OPERATING SYSTEM – What version of Windows   
  WHAT’S THE TROUBLE? – Give enough information  
about your problem so that we can recreate and diagnose it. 
 
FREE Software Drivers for all Addonics Technologies 
Products are available 24 hours per day at the  
World Wide Web Site: www.addonics.com. 
 
Contact Information 
Phone:  408-433-3899 
Fax:  408-433-3898 
Email:  http://www.addonics.com/sales/query/ 
Internet: http://www.addonics.com 
 
TECHNICAL SUPPORT 
Phone:  408-433-3855 
Hours:  8:30 am - 6:00 pm PST 
Email:  http://www.addonics.com/support/query/ 
 
 
 
eSATA connector On / OFF  switch 
Mini-Din power connector