Addonics Technologies ZFamily enclosures zsauscsu User Manual

							 
 
 
 
 
 
 
Addonics 
T E C H N O L O G I E S 
 
 
 
 
Zebra USIB SATA Drive Enclosure 
 
ZSAUSCSU & ZSAUSCSF 
 
 
 
 
 
 
 
User’s Guide 
 
 
 
 
 
FCC Warning Statement  This equipment has been tested and found to comply with the limits for a class B digital device pursuant to Part 15 of the FCC rules.  These limits are designed to provide reasonable protection against harmful interference in a residential installation.  This equipment generates, uses and can radiate radio frequency energy.  If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications.  However, there is no guarantee that interference will not occur in a particular installation.  If the equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged to try and correct the interference by one or more of the following suggestions. Reorient or relocate the receiving antenna Increase the distance between the equipment and the receiver  Connect the equipment to a different power outlet other than the one where receiver is connected Consult a certified television or radio technician 
Enclosure Overview 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Removing the front panel 
 
You can remove the front panel of the enclosure 
to access the drive drawer of the optical drive. 
 
 
 
 
 
 
 
Step 1 
Loosen  the  two  screws  from  the  rear  panel.    Pull  out  the  interior  tray  from  the 
enclosure.  
 
Step 2 
Connect the 15-pin SATA power cable to the power connector of the hard drive. 
Also connect the 7-pin SATA data cable to SATA port of the hard drive. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
15-pin SATA power cable 
Screw 1 
Screw 2 
Power Connector 
Switch 
Fan 
USIB Port 
7-pin SATA data cable    
						

							 
 
 
Step 3 
Use  the  enclosed  screws  to 
secure the hard drive to the tray. 
 
 
 
 
 
 
 
 
Step 4 
After  the  hard  drive  is  installed,  slide  the 
tray  back  into  the enclosure  and  then 
fasten the two screws properly. 
 
 
 
 
 
Connecting the Drive to a Computer: 
 
1. Boot-up your computer. Make sure the USB2.0 or Firewire port from the 
computer functions well. 
2. Connect the power adapter of the enclosure. 
3. Connect the USB or Firewire USIB cable to the USIB port on the back of the 
enclosure and the other end to the USB or Firewire port on the computer. 
Turn on the switch. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Note: Windows 2000 & XP use built-in drivers. No need to install third-party 
drivers. 
 
 
 
 
Technical Support 
 
If you need assistance to get your unit functioning properly, please call Addonics 
Technical Support.  Our technical staff will be happy to assist you, but they will 
need your help to do so.  Calling the technical support staff without all the proper 
information can be both time consuming and frustrating.  Here are some tips to 
help you out: 
 
MODEL NUMBER – Please have this number on hand. 
SYSTEM INFORMATION – Type of computer, peripherals, etc. 
  OPERATING SYSTEM – What version of Windows   
  WHAT’S THE TROUBLE? – Give enough information  
about your problem so that we can recreate and diagnose it. 
 
FREE Software Drivers for all Addonics Technologies 
Products are available 24 hours per day at the  
World Wide Web Site: www.addonics.com. 
 
Contact Information 
Phone:  408-573-8580 
Fax:  408-573-8588 
Email:  http://www.addonics.com/sales/query/ 
Internet:  http://www.addonics.com 
 
TECHNICAL SUPPORT 
Phone:  408-453-6212 
Hours:  8:30 am - 6:00 pm PST 
Email:  http://www.addonics.com/support/query/ 
Screw holes