ADT Security Services GD00Z2Garage Door Opener Controller Installation Guide

							PRINTER’S INSTRUCTIONS:
INSTR,INSTL,GD00Z-2 - LINEAR P/N: 235971 X22- INK: BLACK - MATERIAL: 20 LB. MEAD BOND WITH 80 LB. WHITE COATED COVER - SIZE: 5.500” X 8.500” - SCALE: 1-1 - FOLDING: ALBUM FOLD - BINDING: SADDLE-STITCH
GARAGE DOOR OPENER
REMOTE COMMAND
CONTROLLER
with TILT SENSOR
USA & Canada (800) 421-1587 & (800) 392-0123
(760) 438-7000 - Toll Free FAX (800) 468-1340
www.linearcorp.com
Installation Instructions
GD00Z-2
® 
						

							Regulatory Information  ●Z-Wave®
 is a registered trademark of Sigma Designs Inc. and/or its subsidiaries.
  ●Changes or modi cations not expressly approved by the manufacturer could void the user’s 
authority to operate the equipment.
  ●Les changements ou modi cations non approuvés expressément par la partie responsable de 
la conformité pourrait annuler l’autorité de l’utilisateur à faire fonctionner l’équipement.
  ●This device complies with FCC Part 15 and Canada Rules and Regulations. Operation is subject 
to the following two conditions: (1) This device may not cause harmful interference and (2) 
this device must accept any interference received, including interference that may cause 
undesired operation.
  ●Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils 
radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) 
l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout 
brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le 
fonctionnement.
 WARNING 
This operator system is equipped with an unattended 
operation feature. This door could move unexpectedly. 
NO ONE SHOULD CROSS THE PATH OF A MOVING DOOR!
 WARNING 
This system can be installed on sectional type (roll up) doors 
only per (UL-325). DO NOT INSTALL ON ONE-PIECE DOORS!
 WARNING 
Do not install the Remote Command Controller on 
garage door operators manufactured prior to 1993 
(models without an operational safety beam entrapment 
detection system).
 WARNING 
The Remote Command Controller must be mounted in 
the garage, in sight of the garage door, where the visual 
and audible movement warning indicators can be clearly 
seen and heard.
Regulatory Information 
NOTICE TO USERS IN CALIFORNIA - CR COIN CELL LITHIUM BATTERY INFORMATION: 
THIS PRODUCT CONTAINS A CR COIN CELL LITHIUM BATTERY WHICH CONTAINS 
PERCHLORATE MATERIAL - SPECIAL HANDLING MAY APPLY - SEE 
www.dtsc.ca.gov/hazardouswaste/perchlorate
KEEP AWAY FROM SMALL CHILDREN. IF BATTERY IS SWALLOWED, PROMPTLY SEE A DOCTOR. 
DO NOT TRY TO RECHARGE THIS BATTERY. DISPOSAL OF USED BATTERIES MUST BE MADE IN 
ACCORDANCE WITH THE WASTE RECOVERY AND RECYCLING REGULATIONS IN YOUR AREA. 
						

							1
Table of Contents
Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
The Garage Controller System  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Tilt Sensor Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Mounting the Tilt Sensor  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Enrolling with the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Enrolling the Garage Door Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
To add a Garage Door Controller: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Resetting or Excluding the Garage Door Controller  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
To reset a Garage Door Controller: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Deleting the Garage Door Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Controller Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Mounting the Controller in the Garage  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Controller Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Wiring the Controller to the Opener . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Connecting the Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
System Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Opening and Closing the Garage Door  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Operation Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Indications and Operation Notes  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Tilt Sensor Battery Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
When The Tilt Sensor Battery Gets Low . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
If Something is not Working . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 
						

							2
Figure 1. System Overview
THE TILT SENSOR SENDS DOOR
OPEN OR CLOSED STATUS TO THE
GARAGE DOOR CONTROLLER
THE GARAGE DOOR CONTROLLER
SENDS THE DOOR STATUS TO THE
ADT PULSE SYSTEM
THE ADT PULSE SYSTEM
DISPLAYS THE DOOR STATUS
THE ADT PULSE SYSTEM
COMMANDS THE GARAGE DOOR
CONTROLLER TO OPEN
OR CLOSE THE DOOR
Overview
  ◆Replication is the process of copying or transferring your Z-Wave network from one 
controller to another.
  ◆This is a Security enabled Z-Wave product and must be used with a Security enabled 
Z-Wave controller in order to fully utilize this product. As such, this device will not respond 
to Basic CC commands.
  ◆The GD00Z-2 is a garage door opener remote command transceiver with built-in Z-Wave® 
technology.
  ◆Allows remote operation of a garage door opener using the ADT Pulse touch screen, web 
portal, or mobile app.
  ◆Z-Wave is an Interoperable two-way RF mesh networking technology designed for use with 
a Z-Wave gateway/controller and other Z-Wave enabled devices. 
  ◆Acts as a Z-Wave repeater to improve communications within the Z-Wave mesh network.
  ◆ASSOCIATION: The GD00Z-2 supports 1 Group with 1 Node. Group 1 must be assigned the 
Node ID of the controller to which unsolicited noti cations from the Controller will be sent. 
The ADT Pulse should set this association automatically after inclusion.
Summary of Operation
  ◆Controller connects to the garage door opener’s pushbutton wall console terminals.
  ◆A wireless tilt sensor mounts on the garage door and reports the door’s position to the 
Controller.
  ◆GD00Z-2 responds to Z-Wave commands from ADT Pulse  to open or close the garage door.
  ◆A warning indicator light  ashes and a beeper sounds for 5 seconds before the door begins 
to move.
  ◆If the door does not completely open or close, a second open or close command can be sent 
after 30 seconds.
  ◆If the door does not completely open or close after the second attempt, the Controller 
operation is suspended until a local garage door pushbutton is activated.
Product Description
® 
						

							3
GD00Z-2
GARAGE DOOR
CONTROLLER
POWER
INPUT
JACK
WARNING
LIGHT
INCLUDE
BUTTON
CONNECTION
WIRES
MOUNTING SCREWS
AND ANCHORS
FOR GD00Z-2
POWER
SUPPLY TILT
SENSORSTATUS
INDICATOR
OPTIONAL
ADJUSTABLE
GD00Z-2 MOUNTING
BRACKET
POWER
SUPPLY
RETAINING
BRACKET
SCREWS AND
MOUNTING TAPE
FOR TILT SENSORSCREW AND
MOUNTING HARDWARE
FOR ADJUSTABLE
BRACKET
SCREW FOR
POWER SUPPLY
BRACKET
The Garage Controller System
The GD00Z-2 System consists of three major components:
The Controller — The Controller wires to the garage door opener’s pushbutton terminals, receives 
door status from the tilt sensor, and communicates with the ADT Pulse system.
The Tilt Sensor — The battery powered Tilt Sensor monitors the position of the garage door and 
sends the status to the Controller.
The Power Supply — The Power Supply provides low voltage power to the Controller.
Package Contents
Figure 2. Package Contents 
						

							4
Mounting the Tilt Sensor
The battery powered Tilt Sensor attaches to the top panel of the garage door.
1. Before installation, activate the Tilt Sensor by pulling and removing the battery 
protection strip.
2. If using screws to mount the Tilt Sensor, open the sensor case with a small 
screwdriver.
3. Use the double-sided tape or screws supplied to attach the Tilt Sensor to the top panel 
of the garage door.
  ✓NOTE: Drill two 1/16” pilot holes if using the screws to attach the mounting plate.
4. If the plate was removed for screw mounting, snap the Tilt Sensor on to the mounting 
plate.
  ✓NOTE: Be sure the arrow on the side of the Tilt Sensor points UP.
Tilt Sensor Installation
 USE DOUBLE SIDED TAPE OR
THE TWO MOUNTING SCREWS SUPPLIED
(DRILL 1/16 PILOT HOLES IF REQUIRED)
POST ON
BOTTOM
UP
ARROW
SNAP THE TILT SENSOR
ONTO THE MOUNTING PLATE
TO ACTIVATE THE TILT SENSOR,
REMOVE THE BATTERY PROTECTION PULL STRIP
2
ARROW
ON PLATE
POINTS UP
1
4
ATTACH MOUNTING PLATE
TO TOP PANEL OF THE DOOR TO OPEN THE CASE, FOR SCREW
MOUNTING, TWIST A SMALL
SCREWDRIVER IN THE CASE SLOT 
ARROW
ON SENSOR
POINTS UP
SLOT
3
Figure 3. Tilt Sensor Installation 
						

							5
Enrolling the Garage Door Controller
Before the system can be used, the ADT Pulse system needs to enroll the Garage Door 
Controller. Bring the Controller near your ADT Pulse Gateway and apply power to the 
Garage Door Controller.
  ✓NOTE: Before enrolling device to any Z-Wave network, or after removing it from any Z-Wave 
network, it is recommended that the Controller be factory reset. Reset the Controller by 
pressing the Include button 5 times.(Location of Include button is shown in Figure 2 on 
Page 3). A quick beep followed by a longer beep will indicate proper reset of the GD00Z-2.
To add a Garage Door Controller:
1. Open your Web browser and in the address bar enter:
https://portal.adtpulse.com
2. Enter your Username and Password, then click the Sign In button.
3. Click the System tab, then click the Manage Devices button. The Manage Devices 
Assistant appears.
Enrolling with the System 
						

							6
4. In the Manage Devices Assistant window, click Lights, Thermostats & More.
5. From the drop-down list, select the Garage Door Remote Controller, and then click 
Continue.
6. At the Trigger Device screen, press and hold the Garage Door Controller’s include 
button for 1 second (See page 3, Figure 2 for the location of the include button).
7. Wait while the system  nds the GD00Z-2 Device. When the device is successfully 
recognized, the Found Device screen appears.
  ✓NOTE: Adding the Garage Door Controller can take one or two minutes.
Enrolling with the System (Cont.) 
						

							7
8. Enter a name for the device, and then click Continue.
A message informs you that the device was successfully added.
9. Click Finish.
Enrolling with the System (Cont.) 
						

							8
Resetting or Excluding the Garage Door Controller
If you have trouble adding the Garage Door Controller you can reset the device. Resetting 
the device removes it from a site (Not the same as factory resetting the device). You can 
then try to add the device again.
To reset a Garage Door Controller:
1. In the web portal, click the System tab.
2. Click Manage Devices.
  ◆The Manage Devices Assistant wizard appears.
3. Click Lights, Thermostats & more.
  ◆The Z-Wave Assistant wizard appears.
4. Click Reset Device.
5. Press and release the Garage Door Controller’s include button once.
  ◆The Z-Wave device resets.
6. Click Cancel.
Deleting the Garage Door Controller
To delete the Garage Door Controller:
1. Click the System tab, if it is not already selected.
2. Click the name of the device you want to delete. The device page displays information 
about the selected device.
3. Click Delete. A pop-up window prompts you to con rm the deletion.
4. Click Ye s to complete the deletion.
  ✓NOTE: If you attempt to delete a device that is referenced in an automation, alert, or 
schedule, or replace the device in all automations, alerts, and schedules in which it 
is referenced before you can delete the device. Click OK to exit without deleting the 
device..
Enrolling with the System (Cont.)