ADT Security Services NV412AADT Video Encoder Installation Guide

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
ADT Pulse®  Interactive Solutions  
NV412 A-ADT 
Video Encoder  
Installation Guide  
 
    

NV412A-ADT Video Encoder Installation Guide 
 
Table of Contents 
INTRODUCTION  ...........................................................................................................  1 
Overview .......................................................................................................................  1 
NV412A-ADT Features .......................................................................................  1 
Package Contents...

NV412A-ADT Video Encoder Installation Guide 
 
Introduction 
This installation guide provides simple, step-by -step instructions for configuring 
and installing your  NV412A-ADT  Video Encoder on  your ADT Puls e® w ireless 
system . 
 
Overview   
The NV412A-ADT  (hereafter referred to as the  video encoder) digitizes video 
signals and streams digital images directly to the  ADT Pulse wireless system .  
 
NV412A -ADT Features   
•  Easily installs t o the ADT Pulse wireless system  
•   MPEG4 and JPEG...

NV412A-ADT Video Encoder Installation Guide 
  
Physical Details – NV412A -ADT   
  
Front Panel     
 
Figure 1: Front Panel 
Video Out To ensure the best quality video, attach a coaxial 
terminator to the Video Out  connector . 
Video In  Supports a single composite video source. 
Line Out / 
Line/Mic In  
Not Used 
IMPORTANT 
 THE LINE OUT AND LINE/MIC IN INPUTS ARE NOT 
SUPPORTED BY ADT PULSE.
 
Network LED 
(green)   On
 –  Ethernet connection is detected 
Off  –  Ethernet connection is  not...

NV412A-ADT Video Encoder Installation Guide 
  
Rear Panel    
 
Figure 2: Rear Panel 
 
Ethernet Port Uses a standard Ethernet cable to connect the video 
encoder  to the  ADT Pulse  Gateway.   
Power Port  The supplied 12VDC power adapter connects to the video 
encoder’s power supply .  
Terminal 
Blocks  
Not Used. 
IMPORTANT THE TERMINAL BLOCKS ARE NOT USED WITH ADT 
PULSE.  
 
 
ADT Pulse® Interactive Solutions 3 
  

NV412A-ADT Video Encoder Installation Guide 
 
Installation 
This section  provides details of installing and configuring the  NV412A -ADT 
Video Encoder . 
 
Configuring the NV412A -ADT    
The following instructions provide details of configuring the video encoder . 
1.  Connect the Video Output  of the analog camera to the Video In  on the 
video encoder , using a standard video cable with a BNC connector.  
2. Connect the Video Output Terminator to the Video Out  on the video 
encoder , to ensure the...

NV412A-ADT Video Encoder Installation Guide 
 
3. Click the System  tab , and  then click the Manage Devices  button. 
 
4. In the Manage Devices Assistant , click Cameras. 
 
 
ADT  Pulse® Interactive Solutions 5 
  

NV412A-ADT Video Encoder Installation Guide 
 
5. Click the picture of the NV412A  or select it from the drop- down list, and 
then click the Continue  button.   
 
 
6.  Assign the video encoder  a unique camera  name in the space provided, and  
then type the video encoder’s  MAC ID  in the space provided.  
 
 
NOTE:  A valid MAC ID is 12 characters long and contains only 
numbers and/or the letters A
-F.
 
 
7.  Click the Continue  button.  
 
6  ADT Pulse® Interactive Solutions 
  

NV412A-ADT Video Encoder Installation Guide 
 
8. Connect the video encoder  to the Device LAN  port of the  Gateway  using the 
Ethernet cable.  
9. Connect the power supplies for both the analog camera and the video 
encoder . 
10.  C lick the Continue  button.  
 
 
NOTE:  The 
Power  LED turn s on  briefly , and then starts  blinking for 
approximately 15 -20seconds during startup . After startup 
is complete, the Power and Network LEDs on the f ront of 
the  vide o encoder  turn solid green.
 
 
11....

NV412A-ADT Video Encoder Installation Guide 
 
12. Click  Finish  after the installation is complete.  
 
  
Wall Mounting (Optional)   
If desired, you can mount the NV412A -ADT  to a wall or other solid surface using 
the enclosed mounting brackets.  
 
1.  Attach the mounting brackets to either side of the NV412A -ADT. 
2.  Use two screws per bracket to mount the video encoder  to the surface.  
 
 
8  ADT Pulse® Interactive Solutions