ADT Security Services RC8025BADT Wireless DayNight Camera Installation Guide

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
ADT Pulse®  Interactive Solutions  
RC8025B -ADT  
Wireless  Day/Night Camera  
Installation Guide  
 
    

RC8025B-ADT Wireless Day/Night Camera Installation Guide 
 
Table of Contents 
INTRODUCTION  ...........................................................................................................  1 
Overview .......................................................................................................................  1 
RC8025B-ADT Features  ....................................................................................  1 
Package Contents...

RC8025B-ADT Wireless Day/Night Camera Installation Guide 
 
Introduction 
This installation guide provides step-by -step instructions for configuring and 
installing your RC8025 B-ADT Wireless Day/Night Camera  to your ADT Pulse® 
wireless network. Permanent mounting instructions for the Wir eless Camera 
are also included.  
 
Overview  
The RC8025 B-ADT  Wireless Day/Night Camera (hereafter referred to as the 
wireles s camera ) has an Integrated Microcomputer and a high quality digital 
Image Sensor,...

RC8025B-ADT Wireless Day/Night Camera Installation Guide 
  
Package Contents  
1. RC8025 B-ADT  Wireless Day/Night Camera  
2. Power Adapter  
3. Ethernet Cable  
4. Stand  
5. Installation Guide 
 
 
 
2  ADT Pulse® Interactive Solutions 
  

RC8025B-ADT Wireless Day/Night Camera Installation Guide 
  
Physical Details – RC8025B -ADT    
  
Front Panel     
 
Figure  1: Front Panel  
1. Infrared LEDs 
(behind panel)  
Six infrared light emitting diodes behind the front 
panel help you see clearly at night or in a dark 
environment.   
2. Daylight Sensor This sensor detects daylight levels and adjusts the 
output lighting automatically.   
3. Night Camera Lens The Night Camera Lens is used in a dark 
environment .  
4. Day Camera Lens The Day...

RC8025B-ADT Wireless Day/Night Camera Installation Guide 
  
Rear Panel    
 
Figure  2: Rear Panel  
1. Power Port  This port is used to provide 12V to the wireless camera 
from the supplied  power adapter .  
IMPORTANT 
 DO NOT USE ANY POWER ADAPTER OTHER THAN 
THE ONE SPECIFIED FOR THIS CAMERA. DOING SO 
MAY DAMAGE THE WIRELESS CAMERA.  
2. Ethernet Port   The Ethernet port enables  connectivity of the wireless 
camera  to your ADT Pulse gateway.  
IMPORTANT 
 
•  PLUGGING IN THE ETHERNET CABLE WILL...

RC8025B-ADT Wireless Day/Night Camera Installation Guide 
 
3. Reset/WPS 
Button 
Reset 
When pressed and held for ten (10) seconds, the 
communication configuration of the wireless camera  is  reset 
to the default manufacturer settings.  
 
Wi- Fi Protected Setup ( WPS) 
WPS PBC Mode  
1.   Turn on the wireless camera  without connecting the 
Ethernet cable.  
2.   Wait for three minutes, and then press and release 
(less than 3 seconds). The WPS LED starts blinking.  
3.   Press the WPS button on the...

RC8025B-ADT Wireless Day/Night Camera Installation Guide 
 
Installation 
The following instructions provide details of configuring and installing the 
RC8025B-ADT Wireless Day/Night Camera to your ADT Pulse network.  
 
Configuring and Installing the RC8025B-ADT    
Initial setup is performed  only one time to configure the camera’s wireless 
settings to the ADT Pulse Gateway.   
   
 
Figure  3: Initial Setup  
1.   Assemble the Camera  
Attach the Camera Stand to the camera.  
2.   Connect the LAN...

RC8025B-ADT Wireless Day/Night Camera Installation Guide 
 
IMPORTANT 
 
DO NOT USE ANY POWER ADAPTER OTHER THAN 
THE ONE SPECIFIED. DOING SO MAY DAMAGE THE 
DEVICE. 
 
 
NOTE: 
During start up, the Power LED display s for approximately 10 to 
15 seconds. When installation is complete, the Power LED and  
the Network LED  remain ON . 
 
  
Adding the RC8025B -ADT  to the ADT  Pulse Wireless  
System  
1. Open your web browser. In the address bar, type:  
https://Portal.ADTPulse.com. 
2.  Type your...

RC8025B-ADT Wireless Day/Night Camera Installation Guide 
 
4. In the Manage Devices Assistant , click Cameras. 
 
 
5.  Click the picture of the RC8025  or select it from the drop- down list, and 
then click the Continue  button.   
 
 
6.  Assign the wireless c amera a unique name (this is usually based on the 
location of the wireless c amera) in the space provided, and  then type the  
wireless c amera’s MAC ID  or Server Name.  
8  ADT Pulse® Interactive Solutions