ADT Security Services RC8325ADT Wireless Indoor HD Camera Installation Guide

 
 
 
 
 
 
 
 
 
 
ADT Pulse® Interactive Solutions 
RC8325- ADT 
Wireless  Day/Night HD Camera  
Quick  Installation Guide  
 
    

Table of Contents 
CHAPTER 1 INTRODUCTION ........................................................................\
....  3 
Overview  ........................................................................\
.......................................  3 
Physical Details  ........................................................................\
...........................  4 
Package Contents  ........................................................................\
.......................  6 
CHAPTER 2...

Chapter 1
In

troduction  
This section  provides information about  the  RC8325-ADT  Wireless HD 
Camera's features, components and capabilities.  
Overview 
The RC8325- ADT is a true day /night wireless camera with  HD resolution , 
802.11n Wi- Fi connectivity  and Wi-Fi Protected Setup (WPS) support. This 
camera  is intended for use with ADT Puls e
®. 
Features 
•Standalone Design.   The wireless HD  camera is a standalone system with
built -in CPU and  video encoder. It requires only a power...

Chapter 1 Introduction 
 
Physical Details 
 
Front 
 
F igure  1: Front Panel  
Light 
Sensor 
This is a hardware sensor to detect lux. 
Lens The lens cannot be adjusted. Please ensure that the lens cover 
remains clean. The image quality is degraded if the lens cover is 
dirty or smudged.  
 
Rear 
 
Figure  2: Rear Panel  
Light 
Sensor 
Lens 
Power LED 
Network/WPS LED 
Network Port DC Power Jack 
WPS/Reset Button 
4  RC8325-ADT Wireless Day/Night  HD Camera Installation Guide  
  

Chapter 1 Introduction 
 
Network/WPS 
LED 
(Green, Amber) 
On (Green).  Wireless network connection is available. 
Off.  Wireless network  is not connected or  camera is not 
sending/receiving data.  
Blinking (Green) .  Data is being transmitted or received 
via the w ireless connection.  
On (Amber) .  If the LED is on for 5 seconds and then  turns 
off, the WPS function ha s failed. 
Blinking (Amber) .  The  WPS connection  is processing . 
Power LED 
(Green)  
On.  Power on. 
Off.  No power....

Chapter 1 Introduction 
 
Package Contents 
The following items  are included in the package .  
 
Figure  3: What’s in the Box 
Camera 
Stand 
Screws / 
Anchors (x2) 
Power Adapter 
6   RC8325-ADT Wireless Day/Night  HD Camera Installation Guide  
  

Chapter 2 
Basic Setup  
This section  provides information on how to assemble  and configure 
the  RC8325- ADT Wireless HD  Camera.  
Installation   
1. Assemble the Camera  
Attach the Camera Stand to the  camera. 
2.   Power Up  
Connect the supplied 12V power adapter to the HD  camera and power up. 
Use only the power adapter provided. Using a different one may cause 
hardware damage.  
 
CAUTION: Use only the power adapter provided. Using a different 
one can result in hardware damage. 
 
The Power...

Chapter 2 Basic Setup 
 
Using a Wireless Connection 
The wireless (WPS) connection  between the camera and the Pulse Gateway or 
Total Security ( TS) Base  panel is  performed during the Pulse enrollment . Th is 
process is detailed  starting on page 12. 
 
NOTE: The Wireless and LAN interfaces cannot be used 
simultaneously. M aking a wired LAN connection disables the 
wireless interface. 
4. Check the LEDs  
•  Power LED. At power up, t he Power LED turns on briefly, and then start s 
blinking. It...

Chapter 3 
ADT Pulse Enrollment  
This section provides examples of  t wo  different  methods for  enrolling  the 
RC8325- ADT HD Camera in to the  ADT Pulse network. (1) The first method uses a 
wired connection to enroll the HD Camera to a Pulse Gateway or TS Base panel via 
the Pulse Portal or TS Installer App. (2) The second method uses WPS to wirelessly 
enroll the  HD Camera to a Gateway or TS Base panel via the ADT Pulse Portal or TS 
Installer App. The WPS method is described beginning on page...

Chapter 3 ADT Pulse Enrollment 
 
7. On the  Add Camera screen, enter the camera’s  MAC ID. Do not click Continue 
at this time.  
 
8. Ensure that  the camera  is connected  to the device port  of the Gateway  using 
the  Micro USB to RJ -45 Adapter Cable  / Ethernet cable and connected to the 
supplied 12V DC power adapter .  
9.  After the Power and Network LEDs turn on solid green, click  Continue. 
10.  Wait for the camera to add. It could take a few minutes, especially if an 
upgrade is required....