ADT Security Services Safewatch Plus Entrepreneur User Manual

The bypass key (#) is used to bypass selected zones in your system. A bypassed zone
will NOT be capable of activating an alarm as it is temporarily removed from your
system. Bypassing (also referred to as shunting) is most commonly used to allow
free movement of an area (zone or group of zones) while arming the rest of the
system or to temporarily remove a zone or zones that require service allowing partial
use of the system until repaired. When zones are bypassed, the corresponding
ZONE indicators flash...

Your system may utilize a conventional key switch for arming and disarming the
system. Arming and disarming with a key switch is performed as follows:cl
1.
2.
3.
0
1.
2.
Arming
Verify that the BEADY light is on.
Insert your key into the key switch and turn. Hold for one second and release.
The red ARMED light will blink during the exit delay cycle and then light steady
when the system arms.
Disarming
Insert your key into the key switch and turn. Hold for one second and release.
The red 
ARMED light will...

ProgrammingCertain features of your system are programmable through the control station. The
programming mode is entered by pressing key 9 and holding for three seconds, then
entering the Master User Code.Other programming functions may be possible that
are not detailed in this section.Consult your security representative for a list of the
user programmable features of your system.
WARNING:Do not attempt to program the system unless you have been
properly trained on programming procedures and you are...

Determine your desired new User Code or Master User Code sequence. If you
make an error while programming, press the“ * ” key five times and start over from
step 1.
WARNING: Pressing the “ # ” orl4 * ” key while programmlng a code may
result In Improper code operation, therefore you MUST return to step 1
when an error Is made.
0
1.
2.
3.
4.
5.
To Change A User Code
The system must be disarmed.
Press key 9 and hold for three seconds.The control station will beep three times.
Enter the Master User Code....

An optional feature of your system allows you to assign a certain number of valid
uses to User Code 6. After the code has been used the programmed amount of times,
it automatically becomes disabled. This code may be assigned to a maintenance
person, a maid, or anyone who you would like to be able to arm and disarm the
system for a selected number of times without having to give out your regular code.
After the uses have expired, 
the code will cease to function. It can be re-enabled by
programming in...

Notes 

The TEST mode commands the control station to beep continuously and light the
corresponding zone indicator, each time a zone is violated. The zone indicator of
each tested zone will remain lighted while each succeeding zone is tested. Testing
can be performed only while the system is disarmed. Testing the system should be
performed in both ELECTRICAL ROWER AC ON and STANDBY BATTERY
modes. Your neighbors’ understanding and cooperation is very important. When
you are away from your residence (or commercial...

FIRE DETECTIONYour system may or may not include fire detection, depending upon what options
were purchased, and the local codes and regulations for your area. Fire alarm
systems are active 24 hours a day and cannot be turned off. A!! fire systems require
regular testing and maintenance.Common household dust build-up in smoke
detectors can cause them to false alarm or fail in a time of need. Consult your
security representative for a scheduled maintenance program.
1.
2.
3.
4.
5.
6.The red ALARM indicator...

Emergency Evacuation PlanPreparation and education are of prime importance in the prevention of fire. An
emergency evacuation plan should be established BEFORE an emergency situationarises. Your system may or may not contain 
fire detection and notification
equipment. Be sure to have your installer explain and that you fully understand
exactly what your system consists of. Use the following steps in establishing an
emergency evacuation plan:
1.
2.
3.
4.
5.
Evaluate all possible escape routes from your...

The purpose of heat and smoke detectors is to detect a fire in its earliest stages and
sound an alarm, giving occupants more time to exit the premises before smoke
reaches a dangerous level.
Cl KNOW FIRE HAZARDS
No 
detection device can protect life in all situations; therefore, safeguards should
be taken to avoid such potentially dangerous situations as smoking in bed, leaving
children home alone, and cleaning with flammable liquids such as gasoline.The best fire protection is minimizing 
fire hazards...