ADT Security Services Safewatch Pro 3000 User Manual

– 11 –
)XQFWLRQVRIWKH7RXFKSDGV&RQWLQXHG
ARMEDREADY
6BYPASS
7INSTANT
1OFFAWAY
STAY23
4
TEST
CODE
CHIME
READY
9
85
# 0
A
C
D
B
1
4
3
2
175
18
8
1115
14
16
6
7
9
10
12
13
     English Display Touchpad
ARMED
READY
6BYPASS
7INSTANT
1OFFAWAY
STAY23
4
TEST
CODE
CHIME
READY
9
85
# 0
A
C
D
B
KEYPAD SHOWN WITHOUT SWING-DOWN FRONT DOOR
1
4
3
2
175
18
8
1115
14
16
6
7
9
10
12
13
 Custom English Display Touchpad
(Touchpads shown without swing-down front door)
IMPORTANT!
 •When entering codes and commands,...

– 12 –
(QWU\([LWHOD\V
Your system has preset time delays, known as exit delay and entry delay.
([LWHOD\
Exit delay gives you time to leave through the designated exit door without setting
off an alarm. Exit delay begins immediately after arming your system in any
arming mode and Custom Display touchpads display the message “You May Exit
Now.” 
When “You may exit now” disappears, the system is fully armed. If programmed, a
slow beeping will sound throughout the exit delay period.
Exit Delay Restart....

– 13 –
(QWU\([LWHOD\V&RQWLQXHG
([LW$ODUPV
Whenever you arm the system, the exit delay begins. If an entry/exit door or interior
zone is faulted when the exit delay ends (e.g., exit door left open), the system sounds
an alarm and starts the entry delay timer. If you disarm the system before the entry
delay ends, the alarm sound stops and the message CANCELED ALARM or CA is
displayed on the touchpad, along with a zone number indicating the faulted zone. No
message is sent to the Customer Care...

– 14 –
$UPLQJWKH6\VWHP
6WD\0RGH$UPV3HULPHWHU2QO\(QWU\HOD\2Q
·
Used when you want to arm the system with persons staying inside (or if you have
pets that are moving throughout the premises).
·
The perimeter sensors are armed, but interior sensors are left disarmed.
·
Exit delay begins (you can leave through the entry/exit door, if desired).
·
An alarm sounds immediately if any protected perimeter window or non-entry/exit
door is opened.
·
You may otherwise move freely within the premises.
·...

– 15 –
$UPLQJWKH6\VWHP
$UPLQJ&RPPDQGV
Before arming, close all perimeter doors and windows and make sure the Ready to Arm
message is displayed.
Mode Press these keys… Touchpad Confirms By…
Stay security code + [3] (STAY)
· three beeps
· armed STAY message displayed
· red ARMED indicator lights
Night-Stay security code + [3] + [3]
· three beeps
· NIGHT-STAY message displayed
· red ARMED indicator lights
Instant security code + [7] (INSTANT)
· three beeps
· armed STAY message displayed
· red ARMED...

– 16 –
$UPLQJWKH6\VWHP
6LQJOH%XWWRQ$UPLQJ
The “A”, “B”, “C”, and/or “D” keys on your touchpad may have been programmed for
single-button arming. Note that while it will not be necessary to use a security code
for arming, a security code must always be used to disarm the system.
If Single-Button Arming is programmed:
·
A function key has been assigned to a specific type of arming: STAY mode,
Night-STAY mode, AWAY mode, or STEP-ARMING (see Step-Arming
paragraph).
·
You DO NOT need to enter your user...

– 17 –
8VLQJWKH.H\VZLWFK
8VLQJWKH.H\VZLWFK
Your system may be equipped with a keyswitch for use when arming and disarming.
Red and green lights on the keyswitch plate indicate the status of your system as
follows:
Green Light:Lights when the system is disarmed and ready to be armed (no
open zones). If the system is disarmed and the green light is off, it
indicates the system is not ready (one or more zones are open).
Red Light:Lights or flashes when system is armed in AWAY or STAY mode.
See your...

– 18 –
LVDUPLQJDQG6LOHQFLQJ$ODUPV
8VLQJWKH>2))@NH\
The OFF key is used to disarm the system, silence alarm and trouble sounds, and
clear alarm memories.
IMPORTANT: 
If you return and the main burglary sounder is on, DO NOT ENTER, but
CONTACT THE POLICE from a nearby safe location.
If you return after an alarm has occurred and the main sounder has shut itself off, 
the touchpad
will beep rapidly upon your entering, 
indicating that an alarm has occurred during your
absence.
LEAVE AT ONCE, and...

– 19 –
%\SDVVLQJ3URWHFWLRQ=RQHV
8VLQJWKH%

– 20 –
%\SDVVLQJ3URWHFWLRQ=RQHV
4XLFN%\SDVV
If programmed, Quick Bypass allows you to easily bypass all open (faulted) zones
without having to enter zone numbers individually. This feature is useful if, for
example, you routinely leave certain windows open when arming at night.
1.  
          +   6 + [#]
(Security Code)BYPASS
In a few moments, all open zones will be displayed
and automatically bypassed.
 Make sure that only those
zones that you wish to leave unprotected are bypassed, and
that there...