ADT Security Services Simon 3 User Guide

0
SIMON OWNERS MANUAL 

1
FCC Notices
FCC Part 15 Information to the User
Changes or modifications not expressly approved by Interactive Technologies, Inc. can void the user’s authority to operate the equipment.
FCC Part 15 Class B
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are 
designed to provide reasonable protection against interference in a residential installation.
This equipment generates, uses, and can radiate radio...

2
TABLE OF CONTENTS
        
Introduction to Your System - - - - - - - - - - - - - - - 3
          
Security System Communication  - - - - - - - - - - - 4
             
How to Use Your Control Panel  - - - - - - - - - - - - 6
How to Use Your Touchpads  - - - - - - - - - - - - - - 8
Programming Your System   - - - - - - - - - - - - - - - 9
System Tests & Trouble Messages   - - - - - - -   11
Your Emergency Evacuation Floor Plan   - - - -   13
Alarm System Limitations   - - - - - - - - - - - - - -   14...

3
                
X-10  POWERHOUSE
1
3
5
9 13
71115A
C
E
I M
G KOUNIT CO DEHOUSE CODE
CONTINUOUS
MOMENTARYSOUNDER ONLY
SOUNDER & RELAY
RELAY ONLY
ON
OFF
DOOR/WINDOW
SENSOR
LAMP
MODULE
APPLIANCE
MODULE GARAGE DOOR
MODULEREMOTE
HANDHELD
TOUCHPAD MOTION
SENSOR
KEYCHAIN
TOUCHPADSMOKE
SENSOR
8988G21A.DS4
1
3
5
9 13
71115
A
C
E
I M
G KO
1
3
5
9 13
71115
A
C
E
I M
G KO
7 41
895 2
63OffsPEMERGENCYOnd & s re s Hol hBtoeKy
DISARM
SYSTEM
STATUSDoors &
WindowsARM
ARM
SensorsMotion
-
Introduction to Your System
Your...

4
Security System Communication
Your security system communicates to you through the use of panel voice messages, panel beeps, indicator lights on the panel 
itself, and a numeric pager.
You communicate to your security system with key presses on the Control Panel and Touchpads. Disarming and programming 
require you to input a 4-digit access code. The Master Access Code is 1-2-3-4 when the security system is shipped from 
the factory. You should change it to a code known only by you.
Panel Voice...

5
Alarm Sirens and Lights
Exterior and interior sirens make 3 different alarm sounds on the premises, each indicating a different type of alarm. Sirens will 
time-out and stop sounding after 4 minutes. System controlled lights also indicate the type of alarm.
 
Use the following table to understand alarm sounds and controlled lights.
Numeric Pager
Your installer may have programmed your security system to send a numeric message indicating system activities to your 
pager.
Alarm TypeInterior Siren...

6
How to Use Your Control Panel
The Control Panel interface consists of 3 columns of buttons. They are: HOME SECURITY, CODE, and HOME CONTROL. 
There is a non-medical EMERGENCY button located on the far right. 
HOME SECURITY
ARM Doors & Windows    Press once to turn the security 
system protection on for all protected doors and windows. If a 
door or window is open when you arm the system, it will be 
bypassed, meaning not protected. The SYSTEM STATUS 
light will be lit.
Press  twice to eliminate the...

7
HOME CONTROL
If any of the HOME CONTROL buttons are pressed and a 
sensor or module is not associated (programmed) with this 
feature the Control Panel will say, 
Function not available.
CHIME Doors    Press to cause the Control Panel to beep 
when protected doors or windows are opened.
This is a nice feature to use if you’re busy in one part of 
your home and you want to know when family members 
are going in and out of your home. 
CHIME Special Motion    Press to cause the Control 
Panel to beep when...

8
How to Use Your Touchpads
Touchpads are used to control the security system from any location within or near your home. They have additional home con-
trol features such as light and appliance control.  
Remote Handheld Touchpad
                                            SYSTEM STATUS   Press once to hear information about your system.  See Trouble 
Message information on page 11.
ARM Doors & Windows   Press once to turn the security system protection on for all 
protected doors and windows. 
Press...

9
Programming Your System 
Programming Decals (Upper Decal and Lower Decal)  
The programming decals are visible 
when you open the Control Panel 
cover. These decals are designed to 
make system programming easier for 
you. Always begin by choosing a but-
ton from the START MENU. Follow 
the voice prompts and flow arrows to 
complete the desired task. Notice the 
button flow diagrams under Instruc-
tion Summary to the right of the but-
tons and on the lower decal.
What You Can Change:
Options:
Option 01...