ADT Security Services Simon XTi Quick Operation Guide

Simon XTi Quick Operation Guide 
This is the Quick Operation Guide for the Simon XTi system (models 
600-1054-95R-12 & 600-1054-95R-12-CN). The Simon XTi provides 
a graphical user interface for prog ramming and system operation.  
A piezo siren is provided for al arm and status annunciation. A 
speaker and microphone is  provided for 2-way voice 
communication with the central station. 
Operation 
Use this document to quickly  begin operating your Simon XTi 
security system. Refer to the Simon XTi User...

Icon Description 
 * 
 * Depicts monitored window status. A green check 
indicates all monitored windows are closed. A red 
exclamation point indicates one or more windows 
are open.  
 * 
 * 
Depicts motions sensor status. A green check 
indicates no recent motion detected. A red 
exclamation point indicates motion was detected 
in the last 10 minutes.  
 * 
 * Depicts other changes to protected property in 
your system. A green check indicates all sensors 
are closed and no activity since you last...

Table 3: Status & Settings screen o
 ptions 
Item Description 
  Depicts the status of the AC power and backup 
battery. A red power cord represents loss of AC 
power to the system. A 
green power cord icon 
represents AC power to the system. A red battery 
icon represents a low battery charge. A green 
battery icon represents a fully charged battery. 
Note : These icons only appear on the main 
screen if the backup battery is not fully charged 
or AC power is not working correctly. It is 
recommended...

With this option on, if a single smoke detector goes into alarm, the 
panel will not report for 60 seconds unless another smoke 
detector goes into alarm. If the first smoke detector is cleared of 
an alarm within the first 60 seconds,  no report will be sent to the 
central station unless it or a second smoke detector goes into 
alarm within the panel siren  timeout period (5 minutes). 
Ask your installer how this option is programmed. 
Arming and disarming 
Use the steps below to arm and disarm your...

Touchpads and key fobs 
You can use touchpads and key fobs to control the security 
system from remote locations in and near your home. Interfacing 
with the system using a touchpad is similar to using the panel.  
Status beeps 
The panel sounds status beeps to  alert you to various system 
events and conditions as shown in  Table 4 below . 
Table 4: Status beeps 
Activity Beep response 
Doors+Windows  Exit delay and entry delay beeps sound two times 
every 5 seconds and two times per second during the...

To enable or disable the chime feature: 
1.  Open the Status & Settings screen. The gold icon indicates an 
option is selected. 
2.  To change the value, pre ss On or Off next to Chime 
(depending on the settings your installer programmed, it may 
not be possible to turn on the feature). 
3.  Press Close to exit. 
Special chime 
Th e s p

ecial chime feature allows you to install motion sensors in a 
patio or at the front door, and be notified when someone is 
approaching those areas. These motion...

Simon XTi Quick Operation Guide 7 
Sensor testing notes 
•  Conduct sensor test in all possible environmental conditions 
(For example: interior doors open and closed, HVAC system 
on and off, wireless music system turned on and off). 
•  Conduct sensor test whenever changes are made to the  installation environment that may impact RF performance 
(For example: mirrors insta lled, metal backed wall paper, 
addition of other RF equipment). 
•  If a sensor doesn’t meet minimum packet requirements, 
contact...

Smoke Detector Placement 
 
 
Your floor plan 
Use th
e following guidelines wh en drawing your floor plan: 
•  Show all building levels. 
•  Show exits from each room (two per room are  recommended). 
•  Show the location of all  security system components. 
•  Show the location of any fire extinguishers. Cleaning the touch screen 
If necessary, use a soft cloth to clear smudges on the touch 
screen; do not use glass cleaner on the touch screen. 
Disposal 
Dispose of all equipment is accordance with...

Support 
There may be additional features or programming options for your 
system depending on how it was in stalled. Contact your dealer or 
UTC Fire & Security for more information. 
FCC compliance 
This equipment has been tested and found to comply with the 
limits for a Class B digital device, pursuant to Part 15 of the FCC 
rules. These limits are designed  to provide reasonable protection 
against harmful interference when the equipment is operated in a 
residential environment. This eq uipment...