Advidia A54 OD Dome Camera Quick Start Guide

							Network Dome Camera · Quick Start Guide 
 10 
10 2 Installation 
Before you start: 
 Make sure the device in the package is in good condition and all the assembly parts are included. 
 Make sure all the related equipment is power-off during the 
installation. 
 Check the specification of the products for the installation environment. 
 Make sure the power supply is matched with your required voltage to avoid damage. 
 If the product does not function properly, please contact your 
dealer or the nearest service center. Do not disassemble the camera for repair or maintenance by yourself. 
 Make sure that the wall is strong enough to withstand three times the weight of the camera. 
 
For the camera that supports IR, you are required to pay attention to the following precautions to prevent IR reflection:  
● Dust or grease on the dome cover will cause IR reflection. Please do not remove the dome cover film until the installation 
is finished. If there is dust or grease on the dome cover, clean the dome cover with clean soft cloth and isopropyl alcohol. 
● Make sure that there is no reflective surface too close to the camera lens. The IR light from the camera may reflect back into 
the lens causing reflection.   
						

							Network Dome Camera · Quick Start Guide 
 11 
11 ● The foam ring around the lens must be seated flush against the inner surface of the bubble to isolate the lens from the IR LEDS. 
Fasten the dome cover to camera body so that the foam ring and the dome cover are attached seamlessly.  
2.1 Ceiling Mounting 
Steps:  
1. Drill the screw holes and the cable hole in the ceiling according to the supplied drill template. 
 
Figure 2-1 Drill Template 
2. Hammer the supplied screws to the ceiling. 
 
Do not install the screws into the ceiling completely. It is recommended you install only enough of a screw into the ceiling, 
so as to hook the camera to the screws. Drilling Template
Screw hole 1:for Mounting Base
Hole A:for cables routed through the ceiling
FRONT
A
1
Cable Outlet
1
1  
						

							Network Dome Camera · Quick Start Guide 
 12 
12  
 
Figure 2-2 Installation of the Screws 
3. Use a hexagonal screwdriver to loosen the lock screw on the bubble, and remove the black liner. 
4. Route the cables from the cable hole, and connect the corresponding cables. 
 
You can select to route the cables from the side outlet instead of the cable hole in the ceiling. See Figure below.   
						

							Network Dome Camera · Quick Start Guide 
 13 
13 
 
Figure 2-3 Route the Cables via Side Outlet 
5. Align the screws holes on the camera to the inserted screw, and rotate the camera to hook the camera to the screws. 
6. Tighten the screws. 
7. Install the black liner and bubble back. Side Outlet  
						

							Network Dome Camera · Quick Start Guide 
 14 
14 
 
Figure 2-4 Install the Black Liner and Bubble 
8. Tighten the lock screw on the bubble. 
 
Figure 2-5 Tighten the Lock Screw    
						

							Network Dome Camera · Quick Start Guide 
 15 
15 2.2 Wall Mounting 
 
You need to purchase a wall bracket separately if wall mounting is selected. 
1. Fix the wall bracket to the wall with the screws. 
Please insert the expansion screws first if the camera is mounted to the cement wall, and you can use the self-tapping screws 
directly if camera is mounted to the wooden wall. 
2. Install the bowl-shape cover to the wall bracket. 
 
Figure 2-6 Install the Wall Bracket 
3. Align the supplied rubber ring to the bowl-shape cover. 
4. Insert the screws half-deep to the screws holes on the rubber ring.   
						

							Network Dome Camera · Quick Start Guide 
 16 
16 
 
Figure 2-7 Install the Rubber Ring and Screws 
5. Align the screws holes on the camera to the installed screws, and rotate the camera to hook to the camera to the screws. 
6. Install the black liner and bubble. 
 
Figure 2-8 Install the Black Liner and Bubble Screw   
						

							Network Dome Camera · Quick Start Guide 
 17 
17 7. Tighten the lock screw on the bubble. 
 
Figure 2-9 Tighten the Lock Screw 
2.3 3-axis Adjustment and Lens Adjustment 
2.3.1 3-axis Adjustment 
This series of camera supports 3-axis adjustment, and you can adjust 
the camera to the desired surveillance angle after the black liner is installed.  Lock Screw  
						

							Network Dome Camera · Quick Start Guide 
 18 
18 
 
Figure 2-10 3-axis Adjustment 
2.3.2 Lens Adjustment 
The camera with letter “Z” in its model suffix support electronic lens. You can adjust the lens via the zoom button or focus button on the 
PTZ control interface after you login to a camera. 
 
Please refer to the chapter 3 and chapter 4 for details to login to the camera. 
 
Figure 2-11 Zoom/Focus Adjustment Via PTZ Interface 0°~80°
0°~355°
0°~355°  
						

							Network Dome Camera · Quick Start Guide 
 19 
19 And the camera without letter “Z” in its suffix asks you to adjust the lens after the black liner is installed. 
Connect the camera to a debug monitor so as to get the live view, 
and adjust the zoom lever (T~W) to adjust the zoom, and adjust the focus lever (F~N) to adjust the focus till you get a clear view. 
 
Figure 2-12 Lens Adjustment 
 2
1