Advidia Encoder Vp 8 V2 Vp 16 V2 Quick Start Guide

           VP-8-V2 and VP-16-V2 Encoder  Quick Start Guide                                                                                                                                                                               

VP-8-V2 and VP-16-V2 Series Encoder·Quick Start Guide 2 About this Manual This Manual is applicable to All-in-One NVR (Network Video Recorder). The  Manual  includes instructions  for  using  and  managing  the  product.  Pictures,  charts,  images  and  all  other  information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version in the company website...

VP-8-V2 and VP-16-V2 Series Encoder·Quick Start Guide 3 Regulatory Information FCC Information FCC compliance: This equipment  has  been  tested and  found  to  comply with the  limits for  a Class A  digital  device,  pursuant to  part  15  of  the  FCC  Rules.  These  limits  are  designed  to  provide  reasonable  protection  against  harmful  interference  when the  equipment is  operated  in  a  commercial environment. This  equipment generates,  uses, and can  radiate radio  frequency energy  and,...

VP-8-V2 and VP-16-V2 Series Encoder·Quick Start Guide 4 Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss.  The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may occur if any of the warnings are neglected. Cautions: Injury or equipment damage may occur if any of the cautions are neglected.    Warnings ● Proper configuration of all passwords and other security settings is...

VP-8-V2 and VP-16-V2 Series Encoder·Quick Start Guide 5 Preventive and Cautionary Tips Before connecting and operating your device, please be advised of the following tips: • Ensure unit is installed in a well-ventilated, dust-free environment. • Unit is designed for indoor use only. • Keep all liquids away from the device. • Ensure environmental conditions meet factory specifications. • Use the device in conjunction with an UPS if possible. • Power down the unit before connecting and disconnecting...

 VP-8-V2 and VP-16-V2 Series Encoder · Quick Start Guide 6 Chapter 1  Panel Description 1.1 Front Panel VP-8-V2/VP-16-V2:  Figure 1. 1 VP-8-V2/VP-16-V2 Front Panel  Table 1. 1 Indicator Description  Indicator  Description  1 POWER  Lights in green when the device is powered on. 2  Not Used 3 Tx/Rx 1. Does not light when the network is not connected;  2. Blinks in green when the data is transmitting / receiving;  3. Blinks at higher frequency when the data for transmitting / receiving is larger. 1.2 Rear...

 VP-8-V2 and VP-16-V2 Series Encoder · Quick Start Guide 7 Table 1. 2 Interface Description   Description  1 VIDEO IN 2 AUDIO IN, RCA Connector 3 AUDIO OUT, RCA Connector 4 LAN Network Interface 5 RS-485 Serial Interface 6 12 VDC Power Input 7 Power Switch 8 ALARM IN and ALARM OUT 9 GND  

 VP-8-V2 and VP-16-V2 Series Encoder · Quick Start Guide 8 Chapter 2  Installation 2.1 Pre-Installation The V2 Series Encoder is advanced surveillance equipment that should be installed with care. Please take into consideration the following precautionary steps before installation of the Encoder.    1. Keep all liquids away from the Encoder.  2. Install the Encoder in a well-ventilated and dust-free area. 3. Ensure environmental conditions meet factory specifications.    2.2 Installation During the...

 VP-8-V2 and VP-16-V2 Series Encoder · Quick Start Guide 9 2.3 Access  to VP-8-V2 and  VP-16-V2 ENCODER via Web Browser  Steps: 1. Power on the encoder, and connect the encoder to the network. 2. Input  the  IP  address  into  the  address  bar  of  the  web  browser,  and  click  Enter  to  enter  the  activation interface.  The  default  IP  address  of  the  network  encoder  is  192.0.0.64.  You  are  recommended  to  change  the  default  IP address after your access. 3. Default username is admin...

 VP-8-V2 and VP-16-V2 Series Encoder · Quick Start Guide 10 In the Login dialog box, if you have entered the wrong password for 7 times for the admin user or 5 times for the normal user, the current user account will be locked for 60 seconds.   You should download and install the plug-in for the first time to use.   Figure 2. 2 Message from Webpage 2.4 Starting Live V iew 1. In the live view window, select a playing window by clicking the mouse.    2. Double-click a camera from the device list to start...