AEG Builtin wine cooler SWD81800G1 User Manual

							5. WHAT TO DO IF…
WARNING!
Before troubleshooting, discon-
nect the mains plug from the
mains socket.
Only a qualified electrician or
competent person must do the
troubleshooting that is not in this
manual.
ProblemPossible causeSolution
The appliance does
not operate. The
lamp does not oper-
ate.The appliance is switched
off.Switch on the appliance.
 The mains plug is not
connected to the mains
socket correctly.Connect the mains plug to
the mains socket correctly.
 The appliance has no
power. There is no volt-
age in the mains socket.Connect a different electri-
cal appliance to the mains
socket.
Contact a qualified electri-
cian.
The lamp does not
work.The lamp is in stand-by.Close and open the door.
 The lamp is defective.Refer to "Replacing the
lamp".
The compressor op-
erates continually.The temperature is not
set correctly.Set a higher temperature.
 The door is not closed
correctly.Refer to "Closing the
door".
 The door has been
opened too frequently.Do not keep the door
open longer than necessa-
ry.
 The product temperature
is too high.Let the product tempera-
ture decrease to room
temperature before stor-
age.
 The room temperature is
too high.Decrease the room tem-
perature.
Water flows on the
rear plate of the ap-
pliance.During the automatic de-
frosting process, frost de-
frosts on the rear plate.This is correct.
Water flows into the
appliance.The water outlet is clog-
ged.Clean the water outlet.
ENGLISH11 
						

							ProblemPossible causeSolution
 Products prevent that wa-
ter flows into the water
collector.Make sure that products
do not touch the rear
plate.
Water flows on the
ground.The melting water outlet
does not flow in the evap-
orative tray above the
compressor.Attach the melting water
outlet to the evaporative
tray.
The temperature in
the appliance is too
low.The temperature regula-
tor is not set correctly.Set a higher temperature.
The temperature in
the appliance is too
high.The temperature regula-
tor is not set correctly.Set a lower temperature.
 The door is not closed
correctly.Refer to "Closing the
door".
 Many bottles are stored
at the same time.Store less bottles at the
same time.
 There is no cold air circu-
lation in the appliance.Make sure that there is
cold air circulation in the
appliance.
dEMo appears on
the Display.The appliance is in dem-
onstration mode (dEMo)Keep pressed approxi-
mately 10sec the Alarm
button since a long sound
of buzzer is heard and the
Display shut off for a short
while: appliance start
works regularly.
Upper or lower
square is shown in
the temperature Dis-
play.An error has occurred in
measuring the tempera-
ture.Call your service represen-
tative (the cooling system
will continue to keep food
products cold, but temper-
ature adjustment will not
be possible).
5.1 Replacing the lamp Wine
Cellar
Disconnect the mains plug from the
mains socket.
12www.aeg.com 
						

							Remove the lamp cover by pressing it in-
wards with a tool (e.g. screwdriver) to
free the rear side hookings.
At the same time, free the middle hook
and slide off the cover in the direction of
the arrows.
Replace the used lamp with a new lamp
of the same type and specifically de-
signed for household appliances and
having the same characteristics.
Install the lamp cover.
Connect the mains plug to the mains
socket.
Open the door. Make sure that the lamp
comes on.
5.2 Closing the door
1.Clean the door gaskets.
2.If necessary, adjust the door. Refer
to "Installation".
3.If necessary, replace the defective
door gaskets. Contact the Service
Center.
ENGLISH13 
						

							6. INSTALLATION
6.1 Positioning
WARNING!
If you are discarding an old appli-
ance that has a lock or catch on
the door, you must ensure that it
is made unusable to prevent
young children being trapped in-
side.
The appliance shall have the
plug accessible after installation.
Install this appliance at a location where
the ambient temperature corresponds to
the climate class indicated on the rating
plate of the appliance:
Cli-
mate
classAmbient temperature
SN+10°C to + 32°C
N+16°C to + 32°C
ST+16°C to + 38°C
T+16°C to + 43°C
6.2 Electrical Connection
CAUTION!
Any electrical work required to
install this appliance should be
carried out by a qualified electri-
cian or competent person.
WARNING!
This appliance must be earthed.
The manufacturer declines any li-
ability should these safety meas-
ures not be observed.
AB
C
D E
The wires in the mains lead are
coloured in accordance with the
following code:
A Green and Yellow: Earth
CBrown: Live
E Blue: Neutral
As the colours of the wires in the mains
lead of this appliance may not corre-
spond with the coloured markings iden-
tifying the terminals in your plug, pro-
ceed as follows:
1.Connect the wire coloured green
and yellow to the terminal marked
either with the letter “E“ or by the
earth symbol 
 or coloured green
and yellow.
2.Connect the wire coloured blue to
the terminal either marked with the
letter “N“ or coloured black.
3.Connect the wire coloured brown to
the terminal either marked with the
“L“ or coloured red.
4.Check that no cut, or stray strands of
wire is present and the cord clamp D
is secure over the outer sheath.
5.Make sure the electricity supply volt-
age is the same as that indicated on
the appliance rating plate.
6.Switch on the appliance.
The appliance is supplied with a 13 amp
plug fitted B. In the event of having to
change the fuse in the plug supplied, a
14www.aeg.com 
						

							13 amp ASTA approved (BS 1362) fuse
must be used.WARNING!
A cut off plug inserted into a 13
amp socket is a serious safety
(shock) hazard. Ensure that it is
disposed of safely.
6.3 Ventilation requirements
5 cmmin.
200 cm2
min.
200 cm2
The airflow behind the appliance must
be sufficient.
6.4 Installing the appliance
CAUTION!
Make sure that the mains cable
can move freely.Do the following steps:
Apply the adhesive sealing strip to the
appliance as shown in figure.
ENGLISH15 
						

							Install the appliance in the niche.
Attach the appliance to the niche with 4
screws.
Fix the covers on the screws.
Do a final check to make sure that: • All screws are tightened.
16www.aeg.com 
						

							• The sealing strip is attached tightly to
the cabinet.• The door opens and closes correctly.
6.5 Assembly instructions for the compensator lower part of the
door
With the door open, loosen the two
screws situated in the lower part with-
out unscrewing them completely.
Position the steel compensator as in-
dicated in the figure and insert the up-
per part under the head of the screws.
Align the compensator with the steel
door panel and tighten the screws.
Insert the steel carter inside the com-
pensator as indicated in the figure.
ENGLISH17 
						

							7. NOISES
There are some sounds during normal
running (compressor, refrigerant circula-
tion).
BRRR!HISSS!
CLICK!
BLUBB!
CRACK!
SSSRR
R!
OK
CLICK!CLICK!SSSRRR!SSSRRR!
BRRR!BRRR!HISSS!HISSS!
18www.aeg.com 
						

							BLUBB!BLUBB!CRACK!CRACK!
8. TECHNICAL DATA
   
Dimension of the recess  
 Height1780 mm
 Width560 mm
 Depth550 mm
Voltage 230-240 V
Frequency 50 Hz
The technical information are situated in
the rating plate on the internal left side
of the appliance and in the energy label.
9. ENVIRONMENT CONCERNS
Recycle the materials with the
symbol  . Put the packaging in
applicable containers to recycle it.
Help protect the environment and
human health and to recycle waste
of electrical and electronicappliances. Do not dispose
appliances marked with the symbol with the household waste. Return the
product to your local recycling
facility or contact your municipal
office.
ENGLISH19 
						

							www.aeg.com/shop
222354132-A-172012