AEG Chimney hood X69453BV0 User Manual

MAINTENANCE AND CLEANING11
MAINTENANCE AND CLEANINGMAINTENANCE AND CLEANING
Alarm signal reset
•	 Turn	the	Lights	 and	the	Suction	 motor	off.
•	 Press	 button	H and hold for at least 2 seconds, con-firmation 
is  provided  by  the  fact  that  the  Led  goes  out.
  Before carrying out any maintenance or cleaning isolate  the cooker hood from the mains supply.
Charcoal FiltersIn the recirculation mode the charcoal filters absorb smells and 
unwanted odours.
This filter cannot be washed or regenerated,...

MAINTENANCE AND CLEANING12
      Changing the Halogen Spot Lamp
•	 Remove	the	snap-on	 lamp	cover	 by	levering	 it	from	 under	 the	
metal  ring,  supporting  it  with  one  hand.
•	 Remove	 the	halogen	 lamp	from	the	lamp	 holder	 by	pulling	
gently.
•	 Replace	 the	lamp	 with	a	new	 one	of	the	 same	 type,	making	
sure  that  you  insert  the  two  pins  properly  into  the  housings 
on  the  lamp  holder.
•	 Replace	 the	snap-on	 lamp	cover.
  Replacement filters and light bulbs can be obtained from...

SOMETHING NOT WORKING  -  SERVICE AND SPARE PARTS13
SOMETHING NOT WORKING
SERVICE AND SPARE PARTS
If, having followed these instructions carefully, your cooker hood fails to work properly please carry out
the following checks.
  Symptom
  The cooker hood will not start
  The cooker hood is not working effectively
 
The cooker hood has switched off during operation 
I
f after all these checks, the problem persists, contact your local 
Service Force Centre, quoting the model and serial number.
Please note...

GUARANTEE CONDITIONS14
GUARANTEE CONDITIONS
Standard Guarantee ConditionsWe, AEG, undertake that if within 12 months of the date of the purchase this AEG built-in appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, the company will, at our option, repair or replace the same FREE OF ANY 
CHARGE for labour, materials and carriage on condition that:
•	 The	 appliance	 has	been	 correctly	 installed	and	used	 only	on	the	 electrical	 supply	stated	on	the...

INSTALLATION INSTRUCTIONS  -  ELECTRICAL CONNECTIONS15
INSTALLATION INSTRUCTIONS
  It is dangerous to alter the specifications or attempt to modify this product in any way.
Technical Information
DIMENSIONS             HEIGHT (CANOPY):        649 mm
                  WIDTH (CANOPY):      598 - 898 mm
                  GROSS:       33,3 kg - 37,3 kg
                  NET:      20,1 kg - 23,7 kg
ELECTRICAL SUPPLY: 	 	 	 	 	 		 220-240	V	(50	Hz)
POWER CONSUMPTION:              180 W
FAN MOTOR:...

INSTALLING THE COOKER HOOD16
INSTALLING THE COOKER HOOD
Please ensure that when the appliance is installed it is ea-sily accessible to an engineer in the event of a breakdown.
  All installations must comply with the   local  au-
thorities requirements for the discharge of exhaust air.
  Incorrect installation may affect the safety of this  cooker hood.
Installation Requirements  Before installation check the wall to 
  which the cooker hood is to be fitted for 
  electric cables, water pipes or gas....

INSTALLING THE COOKER HOOD17
INSTALLATION INSTRUCTIONS
Wall drilling and bracket fixingAs a first step, proceed with the following drawings:
•	 a	vertical	line	up	to	the	ceiling	or	up	to	the	upper	limit,	at the centre of the area in which the hood is to be 
fitted;
•	 a	horizontal	line	at	a	minimum		1004	mm	above	the	 cooker top. 
•	 Mark	a	point	(1)	on	the	horizontal	line,	247	mm	to	the	 right of the vertical reference line. 
•	 Repeat	this	operation	on	the	other	side,	checking	that	 the two marks are...

INSTALLING THE COOKER HOOD18
Hood body mounting•	 Open	the	top	 suction	 panel	and	fasten	 it	to	 the	 hood	 body	
on  the  left  using  the  pin,  so  that  it  does  not  close  again.
•	 Unlock	 the	lower	 suction	 panel	by	removing	 the	fixing	 pin	
on  the  left,  and  open  it.
•	 Remove	 the	Metal	 grease	 filters	using	the	 handles	 provi-
ded.
•	 Adjust	 the	two	 screws	 Vr,  in  the  brackets  11 a,  so  that  they 
are  at  the  start  of  their  travel. 
•	 Hook	 the	hood	 body	to	the	 two...

INSTALLING THE COOKER HOOD19
Electrical connection and working test:
•	 Connect	the	hood	 to	the	 mains	 through	 a	two-pole	 switch	
having  a  contact  gap  of  at  least  3  mm.
•	 Remove	 the	grease	 filters	(see	paragraph	 Maintenance)	 being	
sure  that  the  connector  of  the  feeding  cable  is  correctly 
inserted  in  the  socket  placed  on  the  side  of  the  fan.
INSTALLATION INSTRUCTIONS 

www.aeg-electrolux.com/shop436005221_02  -  110915