AEG Freestanding freezer A71101TSX0 User Manual

							ProblemPossible causeSolution
 Large quantities of food
to be frozen were put in
at the same timeInsert smaller quantities of
food to be frozen at any
one time.
 Food placed in the appli-
ance was too warmAllow food to cool to room
temperature before stor-
ing.
 Products to be frozen are
placed too closely to
each otherPlace the products in a way
so that cold air could circu-
late among them
It is too cold inside
the freezerTemperature regulator
may be set incorrectlySet a warmer temperature
The appliance does
not work at all. Nei-
ther cooling nor
lighting worksPlug is not connected to
the mains socket properlyConnect the mains plug
properly
 Power does not reach the
applianceTry connecting another
electrical device to the
power outlet
 The appliance is not
switched onSwitch on the appliance
 There is no voltage in the
mains socket (try to con-
nect another appliance
into it)Call an electrician
The appliance does
not cool at allPlug is not connected to
the mains socket properlyConnect the mains plug
properly
 There is no voltage in the
mains socket (try to con-
nect another appliance
into it)Call an electrician
 The appliance is not
switched onSwitch on the appliance
 Temperature Regulator is
not onCheck the Temperature
Regulator
Green indicator
flashingTemperature sensor
problemCall the service personnel
7.1 Closing the door
1.Clean the door gaskets.
2.If necessary, adjust the door. Refer
to "Installation".
3.If necessary, replace the defective
door gaskets. Contact the Service
Center.
ENGLISH11 
						

							8. TECHNICAL DATA
   
Dimension  
 Height850 mm
 Width595 mm
 Depth635 mm
Rising Time 24 h
Voltage 230-240 V
Frequency 50 Hz
The technical information are situated in
the rating plate on the internal left side
of the appliance and in the energy label.
9. INSTALLATION
WARNING!
Read the "Safety Information"
carefully for your safety and cor-
rect operation of the appliance
before installing the appliance.
9.1 Positioning
This appliance can be installed in a dry,
well ventilated indoor, also in a garage
or cellar, but for optimum performance
install this appliance at a location where
the ambient temperature corresponds tothe climate class indicated on the rating
plate of the appliance:
Cli-
mate
classAmbient temperature
SN+10°C to + 32°C
N+16°C to + 32°C
ST+16°C to + 38°C
T+16°C to + 43°C
9.2 Levelling
When placing the appliance ensure that
it stands level. This can be achieved by
two adjustable feet at the bottom in
front.
12www.aeg.com 
						

							9.3 Location
100 mm
15 mm 15 mm
The appliance should be installed well
away from sources of heat such as radia-
tors, boilers, direct sunlight etc. Ensure
that air can circulate freely around the
back of the cabinet.To ensure best per-
formance, if the appliance is positioned
below an overhanging wall unit, the mini-
mum distance between the top of the cab-
inet and the wall unit must be at least 100
mm . Ideally, however, the appliance
should not be positioned below overhang-
ing wall units. Accurate levelling is ensured
by one or more adjustable feet at the base
of the cabinet. If the cabinet is placed in a
corner and the side with the hinges facing
the wall, the distance between the wall
and the cabinet must be at least 10 mm to
allow the door to open enough so that the
shelves can be removed.
WARNING!
It must be possible to disconnect
the appliance from the mains pow-
er supply; the plug must therefore
be easily accessible after installa-
tion.
9.4 Door reversibility
To carry out the following opera-
tions, we suggest that this be
made with another person that
will keep a firm hold on the doors
of the appliance during the oper-
ations.
To change the opening direction of the
door, do these steps:
• Remove the plug from the power
socket.
• Tilt back the appliance carefully so
that the compressor cannot touch the
floor.
• Unscrew the left foot.
• Unscrew the screws of the door bot-
tom hinge.
ENGLISH13 
						

							2
1
• Take off the appliance door by pulling
it slightly downwards.
• Unscrew the top door hinge pin of the
appliance then screw it back on the
other side.
• Fit the appliance door on the upper
door hinge pin.
• Remove the lower hinge. Put over the
pin in the direction of the arrow.
• Unscrew and install the screw on the
opposite side.
• Install the lower hinge on the opposite
side leaving the position of the door
unchanged.
• Screw in the one screw in the place set
free on the other side as well as the
right adjustable foot .
1
2
3 4
• Remove and install the handle (if fore-
seen) on the opposite side.
• Reposition, level the appliance, wait
for at least four hours and then con-
nect it to the power socket.
Do a final check to make sure that:
• All screws are tightened.
• The door opens and closes correctly.
If the ambient temperature is cold (i.e. in
Winter), the gasket may not fit perfectly
to the cabinet. In that case, wait for the
natural fitting of the gasket.
In case you do not want to carry out the
above mentioned operations, contact
the nearest After Sales Service Force.
The After Sales Service specialist will car-
ry out the reversibility of the doors at
your cost. 
9.5 Electrical Connection
CAUTION!
Any electrical work required to
install this appliance should be
carried out by a qualified electri-
cian or competent person.
WARNING!
This appliance must be earthed.
The manufacturer declines any li-
ability should these safety meas-
ures not be observed.
14www.aeg.com 
						

							AB
C
D E
The wires in the mains lead are
coloured in accordance with the
following code:
A Green and Yellow: Earth
CBrown: Live
E Blue: Neutral
As the colours of the wires in the mains
lead of this appliance may not corre-
spond with the coloured markings iden-
tifying the terminals in your plug, pro-
ceed as follows:
1.Connect the wire coloured green
and yellow to the terminal marked
either with the letter “E“ or by the
earth symbol 
 or coloured green
and yellow.
2.Connect the wire coloured blue to
the terminal either marked with the
letter “N“ or coloured black.
3.Connect the wire coloured brown to
the terminal either marked with the
“L“ or coloured red.
4.Check that no cut, or stray strands of
wire is present and the cord clamp D
is secure over the outer sheath.
5.Make sure the electricity supply volt-
age is the same as that indicated on
the appliance rating plate.
6.Switch on the appliance.
The appliance is supplied with a 13 amp
plug fitted B. In the event of having to
change the fuse in the plug supplied, a
13 amp ASTA approved (BS 1362) fuse
must be used.
WARNING!
A cut off plug inserted into a 13
amp socket is a serious safety
(shock) hazard. Ensure that it is
disposed of safely.
10. NOISE
There are some sounds during normal
running (compressor, refrigerant circula-
tion).
BRRR!HISSS!
CLICK!
BLUBB!
CRACK!
SSSRR
R!
OK
ENGLISH15 
						

							CLICK!CLICK!SSSRRR!SSSRRR!
BRRR!BRRR!HISSS!HISSS!
BLUBB!BLUBB!CRACK!CRACK!
11. ENVIRONMENT CONCERNS
Recycle the materials with the
symbol  . Put the packaging in
applicable containers to recycle it.
Help protect the environment and
human health and to recycle waste
of electrical and electronicappliances. Do not dispose
appliances marked with the symbol with the household waste. Return the
product to your local recycling
facility or contact your municipal
office.
16www.aeg.com 
						

							ENGLISH17 
						

							18www.aeg.com 
						

							ENGLISH19 
						

							www.aeg.com/shop
212000316-00-082013