AEG Freestanding washer dryer L87695NWD User Manual

							9.7 Starting a programme
without the delay start
Press button Start/Pause to start the
programme.
The relevant indicator stops to flash and
stays on.
On the display the indicator of the phase is operation starts to flash.
The programme starts, the door is
locked. The display show the indicator
.
The drain pump can operate
for a short time when the
appliance fills water.9.8  Behaviour of the applianceAfter approximately 15
minutes from the start of the
programme:
• The appliance adjusts automatically the cycle
time to the laundry you
have put in the drum to
have perfect washing
results in the minimum
necessary time.
• The display shows the new time value.9.9  Starting a programme with
the delay start
1. Press button Delay Start again and
again until the display shows the
number of minutes or hours of delay.
The related indicator comes on.
2. Press button Start/Pause.
The appliance starts the countdown of the delay start.
When the countdown is completed, the programme starts automatically.
Before you press button
Start/Pause to start the
appliance, you can cancel or
change the set of the delay
start.9.10  Cancelling the delay start
To cancel the delay start:
1.Press button Start/Pause to set the
appliance to pause.
The related indicator flashes.
2. Press button Delay Start repeatedly
until the display shows 
.
3. Press button Start/Pause again to
start the programme immediately.
9.11  Interrupting a
programme and changing a
option
You can change only some options before they operate.
1. Press button Start/Pause.
The related indicator flashes.
2. Change the option set.
3. Press the button Start/Pause again.
The programme continues.
9.12  Cancelling a running
programme
1. Press button On/Off to cancel the
programme and to deactivate the
appliance.
2. Press button On/Off again to activate
the appliance.
Now, you can set a new washing
programme.
Before starting the new
programme the appliance
could drain the water. In this
case, make sure that the
detergent is still in the
detergent compartment, if
not fill the detergent again.9.13  Opening the doorIf the temperature and level
of the water in the drum are
too high and/or the drum
still rotates you cannot open
the door.
While a programme or the delay start operates, the appliance door is locked.
1. Press button Start/Pause.
In the display the related door lock
indicator goes off.
2. Open the appliance door.
3. Close the door and press button
Start/Pause.
ENGLISH21        
						

							The programme or the delay start
continues.9.14  End of cycle
When the programme has finished, the
appliance stops automatically. The
acoustic signal operates (if it is active).
In the display 
 comes on and the door
locked indicator 
 goes off.
The indicator of Start/Pause button goes
off.
1. Press button On/Off to deactivate
the appliance.
After five minutes from the end of the
programme, the energy saving function
automatically deactivates the appliance.
When you activate the
appliance again, the display
show the end of the last set
programme. Turn the
programme knob to set a
new cycle.
2. Remove the laundry from the
appliance.
3. Make sure that the drum is empty.
4. Keep the door ajar, to prevent
mildew and odours
9.15  Draining water out after
end of cycle
The washing programme is completed,
but there is water in the drum :
The drum turns regularly to prevent the creases in the laundry.
The door lock indicator 
 is on. The
door stays locked.
You must drain the water to open the door:
1. If necessary, decrease the spin
speed.
2. Press the Start/Pause button.
The appliance drains the water and
spins.
3. When the programme is completed
and the door lock indicator 
 goes
off, you can open the door .
4. Press On/Off some seconds to
deactivate the appliance.
The appliance drains and
spins automatically after
approximately18 hours.9.16  AUTO Stand-by option
The AUTO Stand-by function
automatically deactivates the appliance
to decrease the energy consumption
when:
• You do not use the appliance for 5 minutes before you press Start/Pausebutton.
Press the button On/Off to activate
the appliance again.
• After 5 minutes from the end of the washing programme
Press the button On/Off to activate
the appliance again.
The display shows the end of the last
set programme.
Turn the programme knob to set a
new cycle.
If you set a programme or an
option that ends with water
in the drum, the AUTO
Stand-by function  doesn't
deactivate  the appliance to
remind you to drain the
water.10.  DAILY USE - DRYING ONLYWARNING!
Refer to Safety chapters.10.1  Preparation to drying
1.Press button On/Off for some
seconds to activate the appliance
2. Load the laundry one item at a time.
3. Turn the programme dial to the
drying programme applicable for the items to dry.
The display shows a minimum time value
and the following symbols:www.aeg.com22         
						

							The drying symbol comes on.The anti-crease symbol comes on.The drying time symbol comes on.When drying a big amount
of laundry, to have good
drying performances, make
sure that the laundry itself is
not rolled up and that is
uniformly distributed in the
drum.To have best performances
in drying when you wash the
laundry set a spin cycle at
the maximum speed allowed
for your type of items.
You can dry your laundry in two ways:
10.2  Automatic drying
1.Press button Drying Level repeatedly
until a black line appears under one
of the dryness level symbol:
Extra dry levelCupboard dry levelIron dry levelThe drying time symbol goes off
The display shows a time value,
calculated on a default load size. If the amount of your laundry is more or lessthan the default size, the appliance
adjusts automatically the time value
during the cycle.
2. Press button Start/Pause to start the
programme. In the display:
The door locked symbol comes on.The drying symbol starts to flash.The symbol of the set level stays on
(e.g. Cupboard dry).
The other level symbols go off.
The display updates regularly the drying cycle time (every minute).
You cannot set all levels for
all kind of laundry (refer to
"Programmes for automatic
drying" table) .10.3  Timed drying
1.Press button Drying Time repeatedly
to set the time value (see the «Drying
Programme» table).
The drying symbol comes on.The anti-crease symbol comes on.The drying time symbol comes on.Set time value.
Each time you press this button the time
value increases by 5 minutes. The display shows the set time value.
After some seconds the set time value on
the display changes: the appliance
calculates also the duration of the anti-
crease and the cooling phases.
Final time value.
2. Press Start/Pause to start the
programme. The text bar tells that the appliance is drying. The display
shows the new time value every
minute.
The drying symbol starts to flash.The door locked symbol comes on.If you set the time value of
only 10 minutes, the
appliance performs only a
cooling phase.ENGLISH23                      
						

							10.4 At the end of the drying
programme
1. The appliance stops automatically.
2. The acoustic signals operate (if they
are active).
3. In the display 
 comes on.
4. The indicator of button Start/Pause
goes off.
5. The last minutes of the drying cycle
the appliance performs the anti-
crease phase.
The anti-crease symbol 
 flashes.
The door is still locked (the symbol
 is on).
6. Press button On/Off for some
seconds to deactivate the appliance.
After some minutes from
the end of the
programme, the energy
saving function
automatically
deactivates the
appliance.
7. When the door locked light  goes
off you can open the door.
8. Remove the laundry from the
appliance. Make sure that the drum
is empty.
9. Keep the door ajar, to prevent
mildew and odours.
10. Close the water tap.
11.  DAILY USE - WASHING & DRYINGWARNING!
Refer to Safety chapters.11.1  NON-STOP programmeWARNING!
Do not put a plastic device/
ball for the detergent into
the drum.
1. Press button On/Off for some
seconds to activate the appliance .
2. Load the laundry one item at a time.
3. Put the detergent and the additives
in the appropriate compartment.
4. Turn the programme dial to the
washing programme. The display
shows the symbols of the different washing phases.
5. Set the available options.
WARNING!
Do not set a spin speed
lower than the automatic
speed of the set
programme.11.2  Washing and Drying at
automatic levels
1. Press button Drying Level repeatedly
until the black line appears under
one of the dryness level symbol.
The iron dry levelThe cupboard dry levelThe extra dry levelThe drying symbol comes on.The anti-crease symbol comes on.
The display shows that the appliance is ready to start.
The time value on the display is the
duration of both cycles washing and
drying, calculated on a default load
size.
To have a good drying the
appliance does not let you
set a too low spin speed for
the items to be washed and
dried.
2. Press button Start/Pause to start the
programme.
www.aeg.com24               
						

							The set dryness level symbol stays
on (e.g. Cupboard dry). The others
level symbols go off.The door locked symbol comes on.
The display shows the new time value each minute.
The last minutes of the
drying cycle the appliance
performs the anti-crease and
the cooling phases.11.3  Washing and Timed
dryingWARNING!
Do not put a plastic device/
ball for the detergent into
the drum.
1. Press button Drying Time repeatedly
to set the drying time value:
The drying symbol comes on.The anti-crease symbol comes on.The drying time symbol comes on.
The display shows the set drying value
time .
Set drying time value.
Each time you press this button the time
value increases by 5 minutes.
To have a good drying we
suggest you to do not set a
too low spin speed for the
items to be washed and
dried.
2. After some seconds the display
shows the total duration of the
cycles:
Final time value (washing + drying
+ anti-crease + cooling phases)If you set a drying time of
only 10 minutes, the final
time value includes also the
anti-crease and the cooling
phases.
3. Press button Start/Pause to start the
programme.
The door is locked.
The display shows the new time value each minute.
11.4  At the end of the drying
programme
1. The appliance stops automatically.
2. The acoustic signals operate (if they
are active).
3. In the display 
 comes on.
4. The indicator of button Start/Pause
goes off.
5. The last minutes of the drying cycle
the appliance performs the anti-
crease phase.
The anti-crease symbol 
 flashes.
The door is still locked (the symbol
 is on).
6. Press button On/Off for some
seconds to deactivate the appliance.
After some minutes from
the end of the
programme, the energy
saving function
automatically
deactivates the
appliance.
7. When the door locked light  goes
off you can open the door.
8. Remove the laundry from the
appliance. Make sure that the drum
is empty.
9. Keep the door ajar, to prevent
mildew and odours.
10. Close the water tap.
ENGLISH25                  
						

							11.5 Fluff in the fabrics
During the washing and/or drying phase, some types of fabric, (sponge, wool,
sweatshirt) could release fluff.
The released fluff could stick to the
fabrics during the next cycle.
To prevent the fluff in your laundry, we recommend that you:
• Do not wash dark fabrics after you have washed and dried light coloured
fabrics (new sponge, wool, sweatshirt ) and the contrary.
• Line dry this type of fabrics at open air when they are washed the first time.
• Clean the drain filter.
• After the drying phase, clean the empty drum, the gasket and the door
with a wet cloth.11.6  How to remove the fluff
in the garments
To remove the fluff inside the drum, set a
special programme:
1. Empty the drum.
2. Clean the drum, the gasket and the
door with a wet cloth.
3. Set the rinse programme.
4. Press at the same time Spin and
Extra Rinse to activate the cleaning
function until the display shows  CLE.
5. Press Start/Pause to start the
programme.12.  HINTS AND TIPSWARNING!
Refer to Safety chapters.12.1  The laundry load
• Divide the laundry in: white, coloured,
synthetics, delicates and wool.
• Obey the washing instructions that are on the laundry care labels.
• Do not wash white and coloured items together.
• Some coloured items can discolour with the first wash. We recommendthat you wash them separately for the
first times.
• Button up pillowcases, close zippers, hooks and poppers. Tie up belts.
• Empty the pockets and unfold the items.
• Turn multilayered fabrics, wool and items with painted illustrations inside
out.
• Remove hard stains.
• Wash heavy soil stains with a special detergent.
• Be careful with the curtains. Remove the hooks or put the curtains in a
washing bag or pillowcase.
• Do not wash laundry without hems or with cuts. Use a washing bag to wash
small and/or delicate items (e.g.
underwired bras, belts, tights, etc. ).
• A very small load can cause balance
problems with the spin phase. If thisoccurs, adjust manually the items in
the tub and start the spin phase
again.12.2  Stubborn stains
For some stains, water and detergent is
not sufficient.
We recommend that you pre-treat these stains before you put the items in the
appliance.
Special stain removers are available. Use the special stain remover that is
applicable to the type of stain and fabric.
12.3  Detergents and additives
• Only use detergents and additives
specially made for washing machines:– powder detergents for all types of fabric,
– powder detergents for delicate fabrics (40 °C max) and woollens,
– liquid detergents, preferably for low temperature wash
programmes (60 °C max) for all
types of fabric, or special for
woollens only.
• Do not mix different types of detergents.
www.aeg.com26  
						

							• To help the environment, do not usemore than the correct quantity of
detergent.
• Obey the instructions that you find on the on packaging of these products.
• Use the correct products for the type and colour of the fabric, the
programme temperature and the
level of soil.
• If your appliance does not have the detergent dispenser with the flap
device, add the liquid detergents with a dosing ball (supplied by the
detergent's manufacturer).12.4  Ecological hints
• Always start a washing programme
with the maximum load of laundry
allowed.
• If necessary, use a stain remover when you set a programme with a low
temperature.
• To use the correct quantity of detergent, check the water hardnessof your domestic system. Refer to
"Water hardness".
12.5  Water hardness
If the water hardness in your area is high
or moderate, we recommend that you
use a water softener for washing
machines. In areas where the water hardness is soft it is not necessary to use
a water softener.
To know the water hardness in your area, contact your local water authority.
Use the correct quantity of the water
softener. Obey the instructions that you
find on the packaging of the product.
12.6  Drying hintsPrepare the drying cycle
• Open the water tap.
• Check if the drain hose is connected properly. Refer to installation chapter
for more information.
• For the maximum laundry load of the drying programmes, refer to thedrying programmes table.
12.7  Items not suitable for
drying
Do not set a drying programme forthis laundry:
• Very delicate items.
• Synthetic curtains.
• Pieces of clothing with metal inserts.
• Nylon stockings.
• Quilts.
• Bed covers.
• Duvets.
• Anoraks.
• Sleeping bags.
• Fabrics with residue of hair sprays, nail solvents or similar.
• Garments with foam-rubber or materials similar to foam-rubber.12.8  Garment labels
When you dry the laundry, obey the
indications on the labels of the
manufacturers:
•
 = The item can be tumble dried
•
 = The drying cycle is at high
temperature
•
 = The drying cycle is at reduced
temperature
•
 = The item can not be tumble
dried.
12.9  Drying cycle duration
The drying time can change depending
on:
• speed of the last spin
• dryness level
• type of laundry
• weight of the load
12.10  Additional drying
If, at the end of the drying programme,
the laundry is still damp, set a short drying cycle again.
WARNING!
To avoid creasing and
shrinkage do not overdry
the laundry.ENGLISH27      
						

							12.11 General Tips
Refer to the «Drying programmes» table
to find the  average drying times.
Experience will help you to dry the
laundry better. Take note of the duration
of the cycles done before.
To avoid the static charge at the end of
the drying cycle:1. Use fabric conditioner in the washing
cycle.
2. Use special fabric conditioner for
tumble dryers.
When the drying programme is
completed remove the laundry promptly.13.  CARE AND CLEANINGWARNING!
Refer to Safety chapters.13.1  External cleaning
Clean the appliance with soap and warm
water only. Fully dry all the surfaces.
CAUTION!
Do not use alcohol, solvents
or chemical products.13.2  Descaling
If the water hardness in your area is high
or moderate, we recommend that you
use a water descaling product for
washing machines.
Regularly examine the drum to prevent limescale and rust particles.
To remove rust particles use only special
products for washing machines. Do this
separately from the laundry wash.
Always obey the instructions
that you find on the
packaging of the product.13.3  Maintenance wash
With the low temperature programmes it is possible that some detergent stays in
the drum. Perform a maintenance wash
regularly. To do this:
• Remove all laundry from the drum. • Select the cotton programme with the highest temperature with a small
quantity of detergent.13.4  Door seal
Regularly examine the seal and remove
all objects from the inner part.
www.aeg.com28     
						

							13.5 Cleaning the detergent dispenser1.2.3.4.13.6 Cleaning the inlet hose and the valve filter1.2.ENGLISH2912    12 3   
						

							3.4.13.7 Cleaning the drain filterDo not clean the drain filter if the water in the appliance is hot.1.2.3.4.www.aeg.com30 45°
20°  12 21
1  12