AEG Freestanding washer dryer L99695HWD User Manual

3.4.5.6.7.8.9. ENGLISH31 12 12   1
2 1
2  

15.8 Cleaning the inlet hose filter and the valve filterIt could be necessary to clean the filters when:
• The appliance does not fill with water.
• The appliance fills with the water for a long time.
• The indicator of button Start/Pause flashes and the display shows the related alarm. Refer to 'Troubleshooting'.To clean the water inlet filters:• Close the water tap.
• Remove the water inlet hose from the water tap.
• Clean the filter in the inlet hose with a stiff brush.• Remove the inlet hose...

15.9 Emergency drain
Because of a malfunction, the appliance
cannot drain the water.
If this occurs, do steps (1) through (9) of
'Cleaning the drain filter'. If necessary, clean the pump.
When you drain the water with the emergency drain procedure, you must
activate again the drain system:
1. When you drain the water with the
emergency drain procedure, you
must activate again the drain system:
Put 2 litres of water in the main wash
compartment of the detergent
dispenser.
2. Start the programme to...

MessagePossible solution Make sure that the water tap is not clogged or is furred
with lime-scale. Make sure that the filter of the inlet hose and the filter of
the valve are not clogged. Refer to “Care and cleaning”. Make sure that the inlet hose is not damaged. Make sure that the connection of the water inlet hose is
correct.The display tells to check the
drain filter: the appliance
does not drain the water.Make sure that the drain hose is not damaged. Make sure that the drain filter is not clogged....

ProblemPossible solution If the delay start is set, cancel the setting or wait for the
end of countdown. Deactivate the Child Lock function if it is on.The appliance does not drain
the water.Make sure that you have not set a programme without
drain phase. Make sure that you have not set an option which ends
with water in the tub.  The appliance fills with water
and drains immediately.Make sure that the drain hose is in the correct position.
The hose may be too low.The spin phase does not op-
erate or the...

ProblemPossible solutionThe washing results are not
satisfactory.Increase the detergent quantity or use a different deter-
gent. Use special products to remove the stubborn stains be-
fore you wash the laundry. Make sure that you set the correct temperature. Decrease the laundry load.The washing cycle is shorter
than the time displayed.The appliance calculates a new time according to the
laundry load.The washing cycle is longer
than the time displayed.An unbalanced laundry load increases the duration...

16.3 Emergency door opening
In case of power failure or appliance
failure the appliance door remains locked. The washing programme
continues, when the power is restored. If
the door remains locked in case of
failure, it is possible to open it using the
emergency unlock feature.
Before opening the door:CAUTION!
Make sure that the water
temperature and the
laundry are not hot. Wait
till they cool down, if
necessary.CAUTION!
Make sure that the drum is
not rotating. Wait till the
drum stops rotating, if...

Use the gloves.
• Remove the external film. If necessary, use a cutter• Remove the cardboard top.
• Remove the polystyrene packaging materials.• Remove the internal film.• Open the door.
• Remove the polystyrene piece from the door seal and all the items from
the drum.• Put one of the polystyrene packaging elements on the floor behind the
appliance.
• Carefully put down the appliance with the rear side on it.
• Make sure not to damage the hoses.www.aeg.com38      

• Remove the polystyrene protectionfrom the bottom.• Pull up the appliance in verticalposition.• Remove the power supply cable and the drain hose from the hose holders.It is possible to see water
flowing from the drain
hose. This is due to the
testing with water of the
appliances in factory.• Remove the three bolts.
• Use the key supplied with the appliance.
• Pull out the plastic spacers.ENGLISH3912      

• Put the plastic caps in the holes.
• You can find these caps in the user manual bag.We recommend that you keep the packaging and the transit bolts for anymovement of the appliance.17.2  Fixing plate kit
(4055171146)
Available from your authorized dealer.
If you install the appliance on a plinth, secure the appliance in the fixing plates.
Read carefully the instructions suppliedwith the accessory.17.3  Installation on suspended
flooring
Suspended wooden floors are
particularly susceptible to vibration....