AEG Heat pump dryer T65370AH3 User Manual

							6.1 Programmes and options selection OptionsProgrammes 1)AnticreaseTime DryingCotton; Extra Dry Cotton; Cupboard Dry + Cotton; Cupboard Dry  Cotton; Iron Dry Jeans Pillows  Time DryingSynthetic; Extra Dry Synthetic; Cupboard Dry Synthetic; Iron Dry Easy Iron Sports Silk/Lingerie  Wool Refresh  2)1) 
Together with the programme you can set 1 or more options.
2)  Only with the drying rack — see chapter ACCESSORIES6.2  Consumption DataProgrammeSpun at / residual humidityDrying timeEnergy
consump- tionCotton 7 kgCupboard Dry1400 rpm / 50%139 min.1,90 kWh 1000 rpm / 60%159 min.2,17 kWhIron Dry1400 rpm / 50%103 min.1,47 kWh 1000 rpm / 60%117 min.1,68 kWhSynthetic 3,5 kgENGLISH11               
						

							ProgrammeSpun at / residual humidityDrying timeEnergy
consump- tionCupboard Dry1200 rpm / 40%57 min.0,64 kWh 800 rpm / 50%65 min.0,72 kWh7.  OPTIONS7.1  Anticrease
Extends anti-crease phase (30 minutes) at
the end of the drying cycle to 90
minutes. This option prevents laundry from creases. Laundry can be removed
during the anti-crease phase.7.2  Buzzer
When the buzzer option is activated you
can hear the buzzer at the:
• cycle end
• anti-crease phase start and end
• cycle interruption
The buzzer option is by default always
on. You can use this function to activate
or deactivate the sound.
You can activate the Buzzer
option with all programmes.7.3  Time Drying
Operates only with the Time Drying
programme. Lets the user to set special
time of drying programme from
minimum 10 min. to maximum of 2 hours
(in 10 min. steps).7.4  Delay StartLets to delay the start of a
drying programme from
minimum of 30 minutes to
maximum of 20 hours.
1. Set the drying programme and
options.
2. Push the Delay Start button again
and again.
the necessary time of the delay come
into the view on the display (e.g. 
if the programme has to start after 12hours.)
3. To activate the Delay Start option,
push the Start/Pause button. The time to start decreases on the
display.
8.  BEFORE FIRST USEBefore you use the appliance for the first
time do these operations:
• Clean the tumble dryer drum with a moist cloth.
• Start a short programme (e.g. 30 minutes) with moist laundry.At the beginning of drying
cycle (3-5 min.) there could
be a slightly higher sound
level. It is because of start of
the compressor that is
normal for compressor
powered appliances such:
refrigerators, freezers.9.  DAILY USE9.1  Preparing the laundry
• Close the zippers.• Close the fasteners of the duvet covers.www.aeg.com12       
						

							• Do not keep ties or ribbons loose(e.g. apron ribbons). Tie them before
you start a programme.
• Remove all items from the pockets. • If an item has the internal layer made of cotton, turn it inside out. Make sure
that the cotton layer is always external
• We recommend that you set the correct programme applicable for the
type of fabrics that are in the
appliance.
• Do not put fabrics with strong colours together with fabrics with light
colours. Strong colours can bleed.• Use an applicable programme for
cotton jersey and knitwear to prevent
the items to shrink.
• Make sure that the laundry weight is not more than the maximum weight
that is in the programme table.
• Dry only the laundry that is applicable for tumble dryer. Refer to the fabriclabel on the items.Fabric labelDescriptionLaundry that is applicable for tumble drying.Laundry that is applicable for tumble drying and resists higher drying
temperature.Laundry that is applicable for tumble drying but only with low drying
temperature.Laundry that is not applicable for tumble drying.9.2  Loading the laundryCAUTION!
Do not lock the laundry in
between the appliance door
and rubber seal.
1. Pull the appliance door.
2. Load loosely the laundry.
3. Close the appliance door.
9.3  Turning on the appliance
To turn on the appliance:
Push the On/Off button.
If the appliance is on, some indications
come in to the view on the display.
9.4  Auto stand-by function
To decrease the energy consumption,
the automatic stand-by function
deactivates the appliance:
• if the Start/Pause button was not pushed in the time of 5 minutes.
• after 5 minutes from the programme end.
Push the On/Off button to activate the
appliance.
If the appliance is on, some indications come in to the view on the display.9.5  Setting a programme
Use the programme dial to set the
programme.
The possible time to complete the programme comes into the view on the display.
ENGLISH13       
						

							The drying time you see is
related to the load of 5 kg
for cotton and jeans
programmes. For the other
programmes the drying time
is related to the
recommended loads. The
drying time of the cotton
and jeans programmes with
the load more than 5 kg is
longer.9.6  Options
Together with the programme you can
set 1 or more special options.
To activate or deactivate the option push
the applicable button .
When the option is activated the LED
above the button or symbol on the
display comes into the view.
9.7  Child lock option
The child lock can be set to prevent the
children to play with the appliance. The
child lock option locks all push buttons and the programme dial (this optiondoes not lock  On/Off button).
You can activate the child lock option:
• before you push the  Start/Pause
button - the appliance cannot start
• after you push the  Start/Pause button
- programmes and option selection is off.
Child lock option activation:
1. Turn on the dryer.
2. Wait approximately 8 seconds.
3. Select 1 of the available
programmes.
4. Push at the same time and hold
down the  Time Drying  and Delay
Start  buttons .
The symbol  comes into the view on
the display.
5. To deactivate the child lock, push
again the above buttons until the
symbol goes out of the view.9.8  Starting a programme
To start the programme:
Push the  Start/Pause  button.
The appliance starts and the LED above the button does not flash but is stable.
9.9  Programme change
To change a programme:
1. Turn the programme dial to  Stop
position.
2. Set a new programme.
9.10  Programme endClean the filter and drain the
water container after each
drying cycle. (See chapter
CARE AND CLEANING.)
If the drying cycle is completed, the
symbol 
flashes on the display. If the
Buzzer option is on, the acoustic signal
sounds intermittently for 1 minute.
If you do not turn off the
appliance, the crease guard
phase starts. Laundry can be
removed during this phase.
To remove the laundry:
1. Push the On/Off button for 2
seconds to turn off the appliance.
2. Open the appliance door.
3. Remove the laundry.
4. Close the appliance door.
www.aeg.com14        
						

							10. HINTS AND TIPS10.1  Ecological hints
• Spin good the laundry before drying. • Use the load volumes which are specified in the programme chart.
• Clean the filter after each drying cycle.
• Do not use fabric softener to wash and then dry. In the tumble dryer
laundry becomes soft automatically.
• Use the condensate as distilled water, e.g. for steam ironing. If it is necessary
clean the condensate before (e.g. with a coffee filter) to remove possible
small pieces of fluff.
• Always keep the airflow slots on the bottom of the appliance clear.
• Make sure that is good airflow in the appliance installation position.10.2  Adjustment of the
remaining laundry moisture
degree
To change the default degree of the
remaining moisture of the laundry:
1. Turn on the appliance.
2. Wait approximately 8 seconds.
3. Select 1 of available programmes.
4. Push at the same time and hold
down the  Anticrease  and Time
Drying  buttons.
One of the symbols goes into the view
on the display:
 - the maximum dry laundry
 - the more dry laundry
 - the standard dry laundry
5. Push the  Start/Pause  button again
and again until you set necessary
degree.
6. To memorise the setting, push at the
same time the  Anticrease and Time
Drying  buttons for approximately 2
seconds.10.3  Deactivating the Tank
indicator
The water container indicator is by default on. It starts to light at the end of
the drying cycle or during the cycle if thewater reservoir is full. If the draining kit isinstalled the water container is drained automatically and indicator can bepermanently off.
To deactivate the indicator:
1. Turn on the appliance.
2. Wait approximately 8 seconds.
3. Select 1 of available programmes.
4. Push at the same time and hold
down the  Anticrease  and Delay
Start  buttons.
One of 2 configurations is possible: • the Tank indicator: is on and the
symbol 
 goes into the
view - the water container
indicator is permanently  on
• the Tank indicator: is off and the
symbol 
 goes into the
view - the water container
indicator is permanently  off
11. 
CARE AND CLEANING11.1  Cleaning the filter
At the end of each cycle the indicator 
Filter  is on and you must clean the filter.The filter collects the fluff.
The fluff occurs while the
cloths are dried in the
tumble dryer.1. Open the door. Pull the filter.ENGLISH15        
						

							2.Push the hook to open the filter.
3.Use a moist hand to clean both parts
of the filter.
4. If necessary clean the filter with the
brush under warm tap water and/or a
vacuum cleaner. Close the filter.
5. If necessary remove fluff from the
filter socket and gasket. You can use a vacuum cleaner. Put the filter inside
the filter socket.
11.2  Draining the water
container
Drain the condensed water container after each drying cycle.
If the condensed water container is full,
the programme breaks off automatically.
The indicator  Tank is on and you must
drain the water container.
To drain the water container:
1. Pull the water container and keep it
in horizontal position.
2. Move the plastic connection out and
drain the water into a basin or
equivalent receptacle.
3. Move plastic connection in and install
water container.
4. To continue the programme press
the Start/Pause button.
www.aeg.com16          
						

							11.3 Cleaning the heat
exchanger
If the indicator  Condenser flashes, do
the inspection of the heat exchanger and its compartment. If there is a dirt, clean it.
To do the inspection:
1. Open the door. Pull the filter.
2.Move the release button on the
bottom of the door to open the heat
exchanger door.
3. Turn the blockage to unlock the heat
exchanger cover.
4. Lower the heat exchanger cover.
5.If necessary, remove the fluff from
the heat exchanger and its
compartment. You can use wet cloth and/or a vacuum cleaner with the
brush.
6. Close the heat exchanger cover.
7. Lock the blockage until it snaps.
8. Put the filter back.
11.4  Cleaning the drumWARNING!
Disconnect the appliance
before you clean it.
Use a standard neutral soap detergent to
clean the inner surface of the drum and
drum ribs. Dry the cleaned surfaces with a soft cloth.
CAUTION!
Do not use abrasive
materials or steel wool to
clean the drum.ENGLISH17        
						

							11.5 Cleaning the control
panel and housing
Use a standard neutral soap detergent to
clean the control panel and housing.
Use a moist cloth to clean. Dry the
cleaned surfaces with a soft cloth.CAUTION!
Do not use furniture
cleaning agents or cleaning
agents which can cause
corrosion to clean the
appliance.11.6  Cleaning the airflow slots
Use a vacuum cleaner to remove the fluff from the airflow slots.12.  TROUBLESHOOTINGProblem 1)Possible causeRemedy
The tumble dry-
er does not op-
erate.
The tumble dryer is not connected
to mains supply.Connect in at mains socket. Check
fuse in fuse box (domestic installa-
tion).The loading door is opened.Close the loading door.The On/Off button was not push-
ed.Push the On/Off button.The Start/Pause button was not
pushed.Push the Start/Pause button.The appliance is in the standby
mode.Push the On/Off button.
Unsatisfactory
drying result.
Incorrect programme selection.Do the selection of the applicable
programme. 2)The filter is clogged.Clean the filter. 3)The Dry plus option was in mini-
mum level. 4)Change the Dry plus option to the
moderate or maximum level. 4)Too high volume of the load.Obey the maximum load volume.The airflow grill is clogged.Clean the airflow grill in the bot-
tom of the appliance.Dirt on the humidity sensor in the
drum.Clean the front surface of the
drum.Incorrect remaining laundry mois-
ture degree.Adjust remaining laundry moisture
degree. 5)The heat exchanger is clogged.Clean the heat exchanger. 3)www.aeg.com18  
						

							Problem 1)Possible causeRemedyThe loading
door does not
closedThe filter not locked in the posi-
tion.Put the filter in the correct posi-
tion.The laundry is locked between the
door and the seal.Put the load correctly in the drum.
Err (Error) on
the display.
You try to change the programme
or the option after the start of the
cycle.Turn the tumble dryer off and on.
Make the new selection.The option you try to activate is
not applicable with the selected
programme.Turn the tumble dryer off and on.
Make the new selection.Abnormally
elapsing time on
the display.The time to end is calculated on
the basis of the volume and damp-
ness of the laundry.The automatic procedure — this is
not the appliance malfunction.Programme in-
active.The water container is full.Drain the water container, push
the Start/Pause button. 3)
Drying cycle too
short.
Too small laundry volume.Do the selection of time pro-
gramme. The time value must be
related to the load. To dry 1 item
or small quantities of the laundry
we recommend to use short times.The laundry is too dry.Do the selection of time pro-
gramme or higher drying level
(e.g. Extra Dry)
Drying cycle too
long 
6)The filter is clogged.Clean the filter.Too high volume of the load.Obey the maximum load volume.The laundry not spun sufficiently.Spin correctly the laundry.Too low or too high room temper-
ature - this is not the appliance
malfunction.Ensure a room temperature higher
than +5°C and lower then +35°C.1)  If there is an error message on the display (e.g.  E51): Turn the tumble dryer off and on. Make a selec-
tion of the new programme. Push the Start/Pause button. Does not operate? - contact the service centre and give the error code.
2)  Follow the programme description — see PROGRAMME TABLE
3)  See chapter CARE AND CLEANING
4)  Only dryers with the Dry plus option
5)  See HINTS AND TIPS chapter
6)  Note: After maximum 5 hours the drying cycle ends automatically.ENGLISH19 
						

							13. TECHNICAL DATAHeight x Width x Depth850 x 600 x 600 mm (maximal 640 mm)Max. depth with the appliance door open1090 mmMax. width with the appliance door open950 mmAdjustable height850 mm (+ 15 mm - feet regulation)Drum volume118 lMaximum load volume7 kgVoltage230 - 240 VFrequency50 HzNecessary fuse13 ATotal power950 WEnergy efficiency classA+Energy consumption1)2,17  kWhAnnual energy consumption2)260 kWhLeft—on mode power absorption0,44 WOff mode power absorption0,44 WType of useHouseholdPermitted ambient temperature+ 5°C to + 35°CLevel of protection against ingress of solid
particles and moisture ensured by the pro-
tective cover, except where the low voltage equipment has no protection against mois-
tureIPX41)  With reference to EN 61121. 7kg of cotton centrifuged at 1000 rpm.
2)  Energy consumption per year in kWh, based on 160 drying cycles of the standard cotton programme
at full and partial load, and the consumption of the low-power modes. Actual energy consumption per
cycle will depend on how the appliance is used (REGULATION (EU) No 392/2012).14.  INSTALLATION14.1  UnpackingCAUTION!
Before use all parts of the
transport packaging must be
removed.
To remove the polystyrene blockages:
1. Open the door.
2.Pull plastic hose with the polystyrene
blockages out from the drum.www.aeg.com20