AEG Lavamat 70260 Tl User Manual

							TROUBLESHOOTING
The start of the appliance does not occur
or it stops during operation.
First try to find a solution to the problem
(refer to the table). If not, contact the serv-
ice centre.
With some problems, the acoustic
signals operate and the display shows
an alarm code:
•
 - The appliance does not fill with
water.•
 - The appliance does not drain
the water.
•
 - The appliance door is open or
not closed correctly.
•
 - The anti-flood device is on.
WARNING!
Deactivate the appliance before
you do the checks.
ProblemPossible causePossible solution
The appliance
does not fill with
water.The water tap is closed.Open the water tap.
 The water inlet hose is
damaged.Make sure that the water inlet
hose has no damages.
 The filters in the water in-
let hose is blocked .Clean the filters. Refer to 'Care
and cleaning'.
 The water tap is blocked
or is furred with lime-
scale.Clean the water tap.
 The connection of the
water inlet hose is not
correct.Make sure that the connection is
correct.
 The water pressure is too
low.Contact your local water authori-
ty.
The appliance
does not drain the
water.The water drain hose is
damaged.Make sure that the water drain
hose has no damages.
 The filter of the drain
pump is blocked.Clean the filter of the drain
pump. Refer to 'Care and clean-
ing'.
 The connection of the
water drain hose is not
correct.Make sure that the connection is
correct.
 A washing programme
without the drain phase
is set.Set the drain programme.
 The function Rinse &
Hold is on.Set the drain programme.
The appliance
door is open or
not closed correct-
ly. Close the door correctly.
ENGLISH21
 
						

							ProblemPossible causePossible solution
The anti-flood de-
vice is on. • Disconnect the appliance.
• Close the water tap.
• Contact the service centre.
The spin phase
does not operate.The spin phase is off.Set the spin programme.
 The filter of the drain
pump is blocked.Clean the filter of the drain
pump. Refer to 'Care and clean-
ing'.
 Balance problems with
the laundry load.Adjust manually the items in the
tub and start the spin phase
again.
The programme
does not start.The mains plug is not
connected in the mains
socket.Put in the mains plug.
 Blow out fuse in the
household fuse box.Replace the fuse.
 You did not press button
4 .Press button 4 .
 The delay start is set.To start immediately the pro-
gramme, cancel the delay start.
 The Child Lock function
is activated.Deactivate the Child Lock func-
tion.
There is water on
the floor.Leakages from the cou-
plings of the water ho-
ses.Make sure that the couplings are
tight.
 Leakages from the drain
pump.Make sure that the drain pump
filter is tight.
 The water drain hose is
damaged.Make sure that the water inlet
hose has no damages.
You cannot open
the appliance
door.The washing programme
is in operation.Let the washing programme end.
 There is water in the
drum.Set the drain or the spin pro-
gramme.
The appliance
makes an unusual
noise.Incorrect level of the ap-
pliance.Adjust the level of the appliance.
Refer to 'Installation'.
 You did not remove the
packaging and/or the
transit bolts.Remove the packaging and/or
the transit bolts. Refer to 'Instal-
lation'.
 The load is very small.Add more laundry in the drum.
22www.aeg.com
 
						

							ProblemPossible causePossible solution
The appliance fills
with water and
drain immediately.The end of the drain
hose is too low.Make sure that the drain hose is
in the correct position.
The washing re-
sults are not satis-
factory.The detergent you used
was not sufficient or cor-
rect.Increase the detergent quantity
or use a different one.
 You did not remove the
stubborn stains before
you wash the laundry.Use special products to remove
the stubborn stains.
 Incorrect temperature
was set.Make sure that you set the cor-
rect temperature.
 Too much laundry load.Decrease the laundry load.
After the check, activate the appliance.
The programme continues from the point
of interruption.
If the problem occurs again, contact the
service centre.If the display shows other alarm codes,
contact the service centre.
TECHNICAL INFORMATION
DimensionsWidth / Height / Depth400 / 850 / 600 mm
Electrical connection:Voltage
Overall power
Fuse
Frequency230 V
2200 W
10 A
50 Hz
Water supply pressureMinimum0,5 bar (0,05 MPa)
 Maximum8 bar (0,8 MPa)
Water supply 1) Cold water
Maximum loadCotton6 kg
Spin speedMaximum1200 rpm
1) 
Connect the water inlet hose to a water tap with a 3/4'' thread.
ENGLISH23
 
						

							INSTALLATION
UNPACKING
1.Remove the external film. If necessa-
ry, use a cutter.
2.Remove the polystyrene packaging
materials.
3.Tilt the appliance backwards.
4.Turn the appliance on one of the cor-
ners to remove the protection from
the bottom.
5.Open the lid.
6.Remove the polystyrene piece.
7.Open the drum and remove all the
items.
24www.aeg.com
 
						

							8.Remove the power supply cable and
the drain hose from the hose holders.
2
1
9.Remove the three bolts.
1
12
10.Remove the plastic piece.
11.Replace the plastic spacer with the
plastic cap. You can find this cap in
the user manual bag.
12.To install the appliance at the same
level as neighbouring furniture, cut
these plastic pieces.
ENGLISH25
 
						

							WARNING!
Remove all the packaging and the
transit bolts before you install the
appliance.We recommend that you keep the
packaging and the transit bolts for
when you move the appliance.
POSITIONING AND LEVELLING
1.Pull the lever from right to left.
2.When the position of the appliance is
right, put back the lever.
A
3.Install the appliance on a flat hard
floor.
4.Make sure that carpets do not stop
the air circulation below the appli-
ance.
5.Make sure that the appliance does
not touch the wall or other units.
6.Loosen the feet to adjust the level.
Measure with a spirit level. Tighten
the pieces A.
7.A correct adjustment of the appli-
ance level prevents the vibration,
noise and the movement of the ap-
pliance when in operation.
• The appliance must be level and stable.
CAUTION!
Do not put cardboard, wood or
equivalent materials below the
appliance feet to adjust the level.
26www.aeg.com
 
						

							THE INLET HOSE
90˚
1.Connect the hose to the appliance.
Loose the ring nut to set it in the cor-
rect position.
2.Connect the water inlet hose to the
cold water tap with 3/4 thread.
CAUTION!
Make sure that there are no leaks
from the couplings.
Do not use an extension hose if
the inlet hose is too short. Contact
the service centre for the replace-
ment of the inlet hose.
Water-stop device
A
The inlet hose has a water stop device.
This device prevents water leaks in the
hose because of its natural ageing. The
red sector in the window «A» shows this
fault .
If this occur, close the water tap and con-
tact the service centre to replace the
hose.
WATER DRAINAGE
There are different procedures to connect
the drain hose:
ENGLISH27
 
						

							With the plastic hose guide.
 
• On the edge of a sink.
• Make sure that the plastic guide cannot
move when the appliance drains. At-
tach the guide to the water tap or the
wall.
• To a stand pipe with vent-hole.
Refer to the illustration. Directly into a
drain pipe at a height of not less than
70 cm and not more than 100 cm. The
end of the drain hose must always be
ventilated , i.e. the inner diameter of
the drainpipe must be larger than the
external diameter of the drain hose.
Without the plastic hose guide.
• To a sink spigot.
Refer to the illustration. Put the drain
hose in the spigot and tighten it with a
clip. Make sure that the drain hose
makes a loop to prevent that remaining
particles go in the appliance from the
sink.
28www.aeg.com
 
						

							• Directly to a built-in drain pipe in the
room wall and tighten it with a clip.
You can extend the drain hose to
maximum 400 cm. Contact the
service centre for the other drain
hose and the extension.
ENGLISH29
 
						

							30www.aeg.com