AEG Lavamat 86800 Information Manual

31
Drain pump
The drain pump is maintenance-free. It is only necessary to open the 
pump cover if there is a malfunction and water is no longer being 
pumped out, e.g. if the pump wheel is blocked. 
Before loading the machine, please always ensure that there are no for-
eign bodies present in the pockets or in between the items to be 
washed. Paper clips, nails, etc. which may find their way into the wash-
ing machine along with the washing will remain in the drain pump 
housing (foreign body trap that...

32
Technical data
5
This appliance conforms with the following EU Directives:
–73/23/EEC dated 19.02.1973 Low Voltage Directive
–89/336/EEC dated 03.05.1989 EMC Directive inclusive of Amending 
Directive 92/31/EEC
–93/68/EEC dated 22.07.1993 CE Marking Directive
Consumption values
The consumption values were obtained under standardised conditions. 
They may vary when operating in domestic conditions. 
 
Height x width x depth850 x 598 x 640mm
Depth when door is open1,017 mm
Height adjustabilityapprox....

33
Installation and connection instructions
1Safety information concerning installa-
tion
This washing machine cannot be built-in.
Before using for the first time, check the appliance for damage sus-
tained while it was being transported. Do not under any circumstanc-
es connect an appliance that is damaged to the mains. In the event of 
damage to the appliance contact your supplier.
Be sure to remove all the components of the transit packaging before 
using the appliance for the first time. Otherwise...

34
Installing the appliance
Transporting the appliance
1Warning: The washing machine is very heavy. There is a risk of injury. 
Exercise care when lifting the appliance.
Do not lay the washing machine on its front nor on its right side 
(as seen from the front). Electrical components may get wet.
Never transport the appliance without using the transit packaging. 
Only remove the transit packaging when the appliance is in its place 
of installation. Transporting the appliance without the use of the...

35
3Special spanner A and sealing caps B 
(2 units) and C (1 unit) come with 
the appliance.
3.Use special spanner A to remove 
screw D and the compression spring.
4.Use sealing cap C to cap the hole.
5.Use special spanner A to remove the 
two screws E.
6.Use special spanner A to remove the 
four screws F.
7.Remove transit bar G.
8.Screw in the four screws F again.
9.Use sealing caps B to cap the two 
large holes.
Important: Press all sealing caps B 
(2 items) and C (1 item) in firmly so 
that they snap...

36
Making the appliance level
The four feet of the appliance are 
pre-adjusted.
Large degrees of unevenness can be 
compensated for by adjusting the 
four feet of the appliance.
Use the special spanner supplied to 
do this. 
Important: Do not use pieces of 
wood, cardboard or such like to level 
out small degrees of unevenness in 
the floor. Adjust the adjustable feet 
instead.
 

37
Electrical Connection
Any electrical work required to install this appliance should be carried 
out by a qualified electrician or competent person.
1WARNING – THIS APPLIANCE MUST BE EARTHED.
The manufacturer declines any liability should these safety measures 
not be observed.
Before switching on, make sure the electricity supply voltage is the 
same as that indicated on the appliance rating plate.
The appliance is supplied with a 13amp plug fitted. In the event of 
having to change the fuse in the...

38
The switch must not break the yellow and green earth cable at any 
point.
This appliance complies with the requirements laid out in the EEC Di-
rective 76/899.
Voltage 240 V AC: Fuse rating 13 amps
See rating plate for further information.
This appliance meets VDE requirements.
Particular regulations of local electricity authorities must be observed.
This appliance conforms to EEC Directive No. 82/499/EWG on radio in-
terference.
1WARNING! Repairs to electrical appliances must only be carried out by...

39
Water inlet
A 1.35 m long pressure hose is supplied with the appliance. 
If a longer inlet hose is required, only hoses from the manufacturer are 
to be used. Service Force stocks hose kits of different lengths.
3Sealing rings are either inserted in the plastic nuts of the threaded hose 
fitting or are included as spare parts. Do not use any other sealing 
rings. 
Important! All threaded hose fit-
tings must only be tightened by 
hand. 
1.Connect the hose with the right-an-
gle connector to the...

40
Water Drainage
The appliance drain hose should hook into a standpipe, the hook in the 
drain hose is formed using the plastic “U-Piece“ supplied. The standpipe 
should have an internal diameter of approximately 38 mm (see dia-
gram) thus ensuring there is an air break between the drain hose and 
standpipe.
Important! It is essential to lay the drainage hose without kinks.
When discharging into a stand-
pipe ensure that the top of the 
curve in the hose end is no more 
than 90 cm (35.4’’) and no less...