AEM Bosch Injector Plug Kit 4 Pack 302020 User Manual

							  
 
 
ADVANCED ENGINE MANAGEMENT INC. 
2205 126
th Street Unit A    Hawthorne, CA. 90250 
Phone: (310) 484-2322 Fax: (310) 484-0152 
Http://www.aempower.com 
Instruction Part Number: 10-2020 
© 2006 Advanced Engine Management, Inc. 
 
 
 
 
BOSCH STYLE INJECTOR 
CONNECTOR KIT 
 
 
The model 30-2020 Bosch Style Injector Connector Kit contains the parts to assemble 4 
injector connectors. The kit contains Four Bosch style female injector connectors and 10 
contacts (2 extra contacts are included for spares).  
 
IMPORTANT! 
The contacts are “Pull to Seat” meaning you must feed the wire through the connector 
housing BEFORE you crimp on the contacts. The wire is then pulled back into the 
housing and the contact locks in place. The contact cannot be inserted or removed from 
the rear (wire side entry) of the housing. 
 
Contacts (10 Included) 
Plating   Tin Plated 
Cable Range    1.00 - 0.05 mm2 
Outside Cable Diameter  2.40 - 2.03 mm2 
Temperature Range  -40 to 125 C 
Resistance in mOhms at 20 mV  > 10.0 Ohms 
Voltage Drop in mV per amp  > 3.0 Ohms 
 
Housing (4 Included) 
Color   Black 
Cavities or Contacts  2 
Gender   Female 
Temperature Range  -40 to 125 C 
Resistance at 20 mV  > 10.0 mOhm 
Voltage Drop per amp  > 3.0 mV 
Exterior Dimensions  27.8L X 29.6W X 20H 
Seating Process  Pull To Seat 
 
 
This product is legal in California for racing vehicles only and should never be used on public highways.  
						

							AEM Electronics Warranty 
  
Advanced Engine Management Inc. warrants to the consumer that all AEM Electronics 
products will be free from defects in material and workmanship for a period of twelve 
months from date of the original purchase. Products that fail within this 12-month 
warranty period will be repaired or replaced when determined by AEM that the product 
failed due to defects in material or workmanship. This warranty is limited to the repair or 
replacement of the AEM part. In no event shall this warranty exceed the original 
purchase price of the AEM part nor shall AEM be responsible for special, incidental or 
consequential damages or cost incurred due to the failure of this product. Warranty 
claims to AEM must be transportation prepaid and accompanied with dated proof of 
purchase. This warranty applies only to the original purchaser of product and is non-
transferable. All implied warranties shall be limited in duration to the said 12-month 
warranty period. Improper use or installation, accident, abuse, unauthorized repairs or 
alterations voids this warranty. AEM disclaims any liability for consequential damages 
due to breach of any written or implied warranty on all products manufactured by AEM. 
Warranty returns will only be accepted by AEM when accompanied by a valid Return 
Merchandise Authorization (RMA) number.  Product must be received by AEM within 30 
days of the date the RMA is issued. 
  
Please note that before AEM can issue an RMA for any electronic product, it is first 
necessary for the installer or end user to contact the tech line at 1-800-423-0046 to 
discuss the problem.  Most issues can be resolved over the phone.  Under no 
circumstances should a system be returned or a RMA requested before the above 
process transpires. 
  
AEM will not be responsible for electronic products that are installed incorrectly, 
installed in a non approved application, misused, or tampered with.  
  
Any AEM electronics product can be returned for repair if it is out of the warranty period. 
There is a minimum charge of $50.00 for inspection and diagnosis of AEM electronic 
parts. Parts used in the repair of AEM electronic components will be extra. AEM will 
provide an estimate of repairs and receive written or electronic authorization before 
repairs are made to the product.