AEM Gauge Boot 308444 User Manual

							 
ADVANCED ENGINE MANAGEMENT INC. 2205 126th Street Unit A, Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310) 484-0152 www.aemelectronics.com Instruction Part Number: 10-8444 Rev 1  2010 Advanced Engine Management, Inc. 
1 
 
 
 
 
 
AEMs Universal Gauge Boot acts like a wet suit or shower cap for virtually any 52mm gauge. It 
is made of silicone rubber and is designed to stretch onto the back of the gauge cup while 
keeping dust, water, dirt, and mud out of the back of the gauge when installed correctly.  
!!Please note: The installation of this Gauge Boot does not make the gauge waterproof!!  
 
1. Insert the gauge harness/harnesses into the tubular snoot of the boot.  See Figure 1 
below.  The gauge boot is made from silicone rubber and will stretch some.  However, it 
is recommended that the unterminated end of the harness or the smallest connector be 
passed through the snoot.  Note: Use caution during assembly as sharp objects can 
pierce the boot. 
 
 
 
 
2. Connect the harness/harnesses to the gauge and pull the boot over the gauge cup.  It 
may be helpful to turn the boot inside out and roll it onto the cup, inserting the 
mounting studs first.  See Figure 2 below. 
 
                                                
 
 
 
Installation Instructions for PN: 30-8444   
Universal Gauge Boot for 52MM (2 1/16”) Gauges 
Figure 1.  Insert Harnesses 
Figure 2.  Installed Boot  
						

							 
ADVANCED ENGINE MANAGEMENT INC. 2205 126th Street Unit A, Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310) 484-0152 www.aemelectronics.com Instruction Part Number: 10-8444 Rev 1  2010 Advanced Engine Management, Inc. 
2 
 
 
 
 
3. With the gauge boot fully installed on the gauge cup, place the supplied zip tie 
around the snoot on the gauge boot and tighten.  See Figure 3. 
 
 
 
 
 
 
 
 
12 MONTH LIMITED WARRANTY  Advanced Engine Management Inc. warrants to the consumer that all AEM High Performance products will  be free from defects in material  and  workmanship  for  a  period  of  twelve  (12)  months  from  date  of  the  original  purchase.  Products  that  fail  within  this  12-month warranty period will be repaired or replaced at AEM’s option, when determined by AEM that the product failed due to defects in  material  or  workmanship.  This  warranty  is  limited  to  the  repair  or  replacement  of  the  AEM  part.  In  no  event  shall  this  warranty exceed  the  original  purchase  price  of the AEM  part  nor shall AEM be  responsible  for  special,  incidental  or consequential  damages or  cost  incurred  due  to  the  failure  of  this  product.  Warranty  claims  to  AEM  must  be  transportation  prepaid  and  accompanied  with dated  proof  of  purchase.  This  warranty  applies  only  to  the  original  purchaser  of  product  and  is  non-transferable.  All  implied warranties  shall  be  limited  in  duration  to  the  said  12  month  warranty  period.  Improper  use  or  installation,  accident,  abuse, unauthorized repairs or alterations voids this warranty. AEM disclaims any liability for consequential damages due to breach of any written  or  implied  warranty  on  all  products  manufactured  by  AEM.  Warranty  returns  will  only  be  accepted  by  AEM  when accompanied by a valid Return Goods Authorization (RGA) number.  Product must be received by AEM within 30 days of the date the RGA is issued.  Please note that before AEM can issue an RGA for any product, it is first necessary for the installer or end user to contact the AEM Performance Electronics tech line at 1-800-423-0046 to discuss the problem.  Most issues can be resolved over the phone.  Under no circumstances should a system be returned or a RGA requested before the above process transpires.  
 
Need additional help?  Contact the AEM Performance Electronics tech department at 
1-800-423-0046 or [email protected], or visit the AEM Performance Electronics 
forum at http://forum.aempower.com/forum/ 
Figure 3.  Installed Zip Tie