AEM Series 2 Plug Play EMS 306050 User Manual

							Page 11 of 13 
 
Pin # 00-01 Integra / 98-02 Accord / 99-00 Civic AEM EMS 30-6050 I/O Availability 
D1 --- Injector 5 Output Avail, Switched Ground, 1.5A Max 
D2 --- Injector 7 Output Avail, Switched Ground, 1.5A Max 
D3 --- Idle #1 Output Avail, Switched Ground, 1.5A Max 
D4 --- High Side Driver 4 Output Avail, Switched +12v, 1.5A Max 
D5 --- Idle #4 Output Avail, Switched +12v, 1.5A Max 
D6 --- +5V Sensor Output Avail, 5V sensor reference power 
D7 --- EGT #2 Input Avail, jumper set for 0-5V Input 
D8 --- ADCR14 Input Available, 0-5V in, 100k pull up to 5v 
D9 --- Sensor Ground Output Avail, Sensor Ground 
D10 --- CAN1H --- Dedicated 
D11 --- Switch 2 Input Avail, Switched GND Input 
D12 --- Switch 3 Input Avail, Switched GND Input 
D13 --- High Side Driver 3 Output Avail, Switched +12v, 1.5A Max 
D14 --- CAN1L --- Dedicated 
D15 --- Baro Volts --- Avail, 0-5V input 
D16 --- PW 2 Output Avail, Boost Solenoid Output 
 
 
 
 
 
 
 
 
 
 
 
*** Important: Wire View of AEM EMS. Reference diagram below for pin location. *** 
  
						

							Page 12 of 13 
 
30-1050 (Series 1) vs 30-6050 (Series 2)  OBD2B Honda EMS pin differences: 
The EMS functions assigned to certain pins have been changed and no longer match the 
30-1050 EMS. Unless otherwise noted, the following pins and functions will need to be 
manually reconfigured after using AEMTuner to convert a V1.19 (30-1050, Series 1 EMS) 
calibration for use with the 30-6050 Series 2 hardware.  
 
Pin OBD2B Honda 30-1050 function 30-6050 function Notes 
A1 --- Coil #5 Coolant dash sig Coil 5 not available 
A10 Service Check Signal Injector #10i Injector 12 Inj12 controlled independently of Inj10 
A11 --- PW #2i PW 3 PW 3 controlled independently of PW2 
A13 --- Injector #9i Coil 7 Use A14 for injector output (INJ 11) 
A14 --- FM Injector 11 FM not available 
A22 --- Low Side #9 Coil 8 Low Side 9 not available 
B24 --- --- Knock 2  
D10 --- --- CAN1H  
D14 --- --- CAH1L  
  
						

							Page 13 of 13 
 
 
AEM Electronics Warranty 
  
Advanced Engine Management Inc. warrants to the consumer that all AEM Electronics 
products will be free from defects in material and workmanship for a period of twelve 
months from date of the original purchase. Products that fail within this 12-month warranty 
period will be repaired or replaced when determined by AEM that the product failed due to 
defects in material or workmanship. This warranty is limited to the repair or replacement of 
the AEM part. In no event shall this warranty exceed the original purchase price of the 
AEM part nor shall AEM be responsible for special, incidental or consequential damages 
or cost incurred due to the failure of this product. Warranty claims to AEM must be 
transportation prepaid and accompanied with dated proof of purchase. This warranty 
applies only to the original purchaser of product and is non-transferable. All implied 
warranties shall be limited in duration to the said 12-month warranty period. Improper use 
or installation, accident, abuse, unauthorized repairs or alterations voids this warranty. 
AEM disclaims any liability for consequential damages due to breach of any written or 
implied warranty on all products manufactured by AEM. Warranty returns will only be 
accepted by AEM when accompanied by a valid Return Merchandise Authorization (RMA) 
number.  Product must be received by AEM within 30 days of the date the RMA is issued. 
  
Please note that before AEM can issue an RMA for any electronic product, it is first 
necessary for the installer or end user to contact the tech line at 1-800-423-0046 to 
discuss the problem.  Most issues can be resolved over the phone.  Under no 
circumstances should a system be returned or a RMA requested before the above 
process transpires. 
  
AEM will not be responsible for electronic products that are installed incorrectly, installed 
in a non approved application, misused, or tampered with.  
  
Any AEM electronics product can be returned for repair if it is out of the warranty period. 
There is a minimum charge of $50.00 for inspection and diagnosis of AEM electronic 
parts. Parts used in the repair of AEM electronic components will be extra. AEM will 
provide an estimate of repairs and receive written or electronic authorization before 
repairs are made to the product.