Agio International Coleman Stainless Steel Outdoor Workbench User Manual

							QTYDESCRIPTIONORDER PART #QTYDESCRIPTIONORDER PART #QTYDESCRIPTIONORDER PART #M10 X 55MM BOLT3M6 X 50MM BOLT6M6 X 16MM BOLT16M6 NUT126MM WASHER610MM WASHER512MM  WASHER4
10MM END CLIP2
12MM END CLIP410MM PVC COVER212MM PVC COVER2
M6 PVC NUT COVER4LARGE WHEEL2WHEEL COVER4AXLE SLEEVE3RIGHT SUPPORT
FRAME1LEFT SUPPORT
FRAME1CUSHION
HANDLE GRIP1CASTERS2FRONT SUPPORT 
BAR1REAR SUPPORT
BAR1MIDDLE SUPPORT
FRAME1FRONT PANEL1COILED SHELF1DRAIN PLUG1DOWEL RODS3REAR FAUCET
PANEL1FOLDING
COUNTER1AXLE FOR 
FOLDING COUNTER1DRAWER1BOTTOM TRAY2“S” HOOKS6FAUCET1FOLDING COUNTER
 HINGE2STEP 1  
identify all parts packed in carton against the parts list. Remove all protective materials. Place parts 
on a non-arasive surface to avoid scratching. If you are missing any parts or are unsure how to proceed with assembly, call our Customer Service Center at 1-800-416-3511 (Mon - Fri 9a-5p 
EST). Do not attempt assembly if any parts are missing or damaged.
Read entire assembly instructions before beginning assembly.
A
F
E
D
C
B
K
J
I
H
G
M
L
N
S
R
Q
P
O
X
W
V
U
T
Z
Y
AA
FF
EE
DD
CC
BB
JJ
I I
HH
GGWHEEL AXLE1SINK TOP BASIN1STEP 2  WHEEL ASSEMBLY  
Insert wheel axle (M) through bottom shaft of right side support frame 
(Q).so that it is centered inside the shaft with equal amount of axle on each side. Snap 12mm end clip (I) on notch in axle closest to the right 
side support frame (Q).  Add the following parts to the axle in this order: 
12mm washer (G), wheel cover (O), axle sleeve (P), wheel (N),  wheel cover (O), 12mm washer (Q), 12mm end clip (I) as shown in figure 1. Be 
sure the wheel is inserted over the axle sleeve in a manner that allows it 
to rotate freely.  Secure the wheel assembly on the axle with the 12mm washer clip (I).  Repeat procedure for opposite side wheel.STEP 3 LEFT SIDE SUPPORT FRAME ASSEMBLY
Screw in the two casters (T) into the bottom of the left side support frame (R) as 
shown in figure 2.  Add the cushion handle grip (S) to the left side support frame 
(R) as shown in figure 2. Insert two M6 x 50mm bolts (B) through end of cushion 
grip handle and through the holes in the left side support frame.  Add a 6mm washer (E), 6mm nut (D).  Tighten with wrench. Do not over tighten. Add M6 PVC 
cover to the end of each nut. Repeat on opposite side of cushion grip handle.Figure 1Figure 2WB0001WB0014WB0013WB0012WB0011WB0010WB0009WB0008WB0007WB0006WB0005WB0004WB0003WB0002WB0023WB0022WB0021WB0020WB0019WB0018WB0017WB0016WB0015WB0024PAGE 1TOOLS REQUIRED FOR ASSEMBLY
   Hex Wrench   Hex Bolt DriverMULTI-PURPOSE WORK BENCH ASSEMBLY INSTRUCTIONS
#92558 
						

							STEP 4  FRAME ASSEMBLY
Connect right side support frame (Q) and left side support frame (R) 
using the rear support bar (V). Be sure that the hole in the center of the rear support bar is facing up. Add a 10mm washer (F) to a M10 x 55 mm bolt (A) and insert through the left side frame support(r) into the fixed nuts in the rear support bar (V) as shown in figure 3. Repeat for 
opposite side. (Q).  Attach front support bar to middle support frame as shown in figure 3  using a M6 x 16mm bolt.  Tighten with wrench. Do 
not over tighten. With bottom of rear portion of middle support frame resting on the rear support bar, attach front support bar to right side support frame (with wheels) using M6x 16mm bolt (C) as shown in figure 3. Tighten with wrench. Do not over tighten. Attach middle 
support frame (W) to the rear support bar (V). Align middle support bar with hole in rear support bar as shown in figure 4. Add a 10mm washer (F) to an M10 x 55mm bolt (A). Insert bolt through middle support frame and into the fixed nut inside the rear support bar.   STEP 5  COILED SHELF ASSEMBLY
Attach coiled shelf (Y) to right side support frame (Q) and middle 
support frame (W) using M6 x 16 bolts (C) as shown in figure 4. 
Position coiled shelf between the right side and middle support frames so that coiled portion of the panel is acing towards the bottom. Insert bolts through the holes from behind the coiled shelf and into the fixed nuts inside the right side and middle support frames.  Use hex wrench to tighten completely.  Do not over tighten.  Attach front panel to left 
side and middle support panels as shown if figure 4 using M6 x 16mm 
bolts (C). Insert bolts through holes from behind the front panel into the fixed nuts in the front portion of the left side and middle support frames. Tighten using hex wrench.  Do not over tighten. STEP 6  SINK ASSEMBLY
Install sink drain/stopper assembly  (AA) as shown in figure 5.  
Separate the three pieces and insert the center gasket into the whole in the sink basin. Insert the funnel-shaped portion into the sink drain as shown. From underneath the sink basin, attach the bottom portion of the sink drain/stopper assembly onto the bottom portion of the funnel shaped piece to hold firmly in place.  Figure 3Figure 4Figure 5PAGE 2 
						

							STEP 6  SINK ASSEMBLY (continued)
Position the sink top assembly (Z) over the left side, right side and 
middle support frames, making sure the holes for the bolts are properly aligned.  Once in proper position, use M6 x 16mm bolts (C) to attach sink top/basin assembly to the left support frame.  Insert bolts through holes in sink top into the fixed nuts in the left side support frame. Repeat procedure for right side support frame.  Insert M6 x 50mm bolts (B) through the holes in the middle portion of the sink top/basin assembly through the holes in the middle support frame.  Be sure to insert the bolts in the direction towards the right side support frame as shown in figure 6.  Add a 6mm washer (E) and 
an m6 nut to the end of each bolt.  Tighten with wrench. Do not over tighten.  Figure 6Figure 7STEP 7  FAUCET AND FOLDING COUNTER ASSEMBLY
 Attach rear faucet panel (CC) to left side support frame and middle support frame using M6 x 16mm bolts (C). Insert bolts outwards through holes from behind the rear faucet panel and into the fixed nuts in the middle support frame. Repeat procedure for opposite side.  Tighten bolts using hex wrench. Tighten completely. Do not 
over tighten.
Attach the three dowels rods (BB) by snapping into place as shown.  
Two on left side, one on right side beneath the coiled shelf.  
Attach folding counter (DD) to right side of the  assembled unit.  
Position the folding counter between the axle guides on the right side support frame (just below where it meets with the sink top/basin assembly). Slide the folding shelf axle (EE) through the axle guides and through the hollow shaft of the folding shelf.   Add 10mm washer to each end of the axle. Secure into place by attaching 10mm end clips (H) to each end of the axle.  Attach lower part of front hinge to 
the front right side support frame as shown in figure7.  Attach one 
end of hinge to threaded post on right side frame and the other end of hinge to threaded post on the underside of the folding shelf. Secure with M6 nut (D).  Tighten with wrench. Repeat for remaining hinge.  Note: hinge will lock with shelf in the “up” position. Collar on hinge will slide down to lock into position.  
Attach faucet (II) to rear faucet panel (CC) by unscrewing plastic 
gasket and sealer ring from faucet head. Place faucet through hole 
in rear faucet panel and re-screw gasket and ring.  Adjust faucet until properly aligned.  Tighten.  PAGE 3 
						

							STEP 8 FINAL TOUCHES
Drawer assembly. Tilt the front end of drawer up and slide into 
track.  Make sure track and drawer runners are properly aligned.  
Slide the two bottom trays (GG) into frame as shown in figure 
8. 
At this time, make sure all nuts and bolts are tightened 
completely  using wrench and hex key wrench. Do not over tighten.  Add 12mm PVC  cover (K) to each end of wheel axle and 10mm PVC cover (J) to each end of the folding shelf axle as shown in figure 8. 
 LIMITED WARRANTY
This warranty is extended to the original purchaser and applies to defects in materials and workmanship of our 
Outdoor Living patio furniture, provided your furniture is maintained with care and used only for personal, residential purpose.
Frames and Welds are warranted to be free from defects in materials and workmanship for  a period of five years.  Exclusions: Items used for commercial, contract or other non-residential purposes, display models, items 
purchased “as is,” or items damaged due to acts of nature, vandalism, misuse or improper assembly are not covered.  Discoloration or fading of the finish or fabric (if applicable) as a result of exposure to the elements, chemicals or spills are not covered.  Table top breakage, corrosion or rusting of hardware, loss of use or other 
incidental damages are not covered.
If within the stated warranty period a product is found to be defective in material or workmanship, the purchaser 
must contact the manufacturer’s customer service center at 1-800-416-3511.  The manufacturer will, at its option, repair or replace the defective parts.
Warranty is to the original purchaser only and is non-transferrable. Any replacement of warranted items will be in 
the original style and color.  If original style and color is not available or has been discontinued, an item of similar style and color will be substituted. As some states do not allow exclusions or limitations on an implied warranty, 
the above exclusions and limitations may not apply.  This warranty gives you specific rights and you may also 
have other rights which vary from state to state.Figure 8PAGE 4