Home > Aimco Brakes > Assembly Systems > Aimco Brakes Assembly System ERGOARM Tool Support Systems Operation Manual

Aimco Brakes Assembly System ERGOARM Tool Support Systems Operation Manual

Here you can view all the pages of manual Aimco Brakes Assembly System ERGOARM Tool Support Systems Operation Manual. The Aimco Brakes manuals for Assembly Systems are available online for free. You can easily download all the documents as PDF.

Overview View all the pages Comments

Page 1

$Page 1 PO Box 1\f4\f0, Portland OR 97\b9\b-04\f0 • 800-85\b-13\f8 • Fax 800-58\b-9015www.aimco-global.com ERGO-ARM Tool Support Systems Operations Manual MODELS AD-D1098S/SAC& AD-D1098P/PAC Ergo Arm Operations \:Manual_3000 nutrunner\: manual.qxd \f/\b/2013\: \f:46 AM Page 1$

PO Box 1\f4\f0, Portland OR 97\b9\b-04\f0  • 800-85\b-13\f8 • Fax 800-58\b-9015www.aimco-global.com
ERGO-ARM
Tool Support Systems
Operations Manual
MODELS AD-D1098S/SAC& AD-D1098P/PAC
Ergo Arm Operations \:Manual_3000 nutrunner\: manual.qxd  \f/\b/2013\:  \f:46 AM  Page 1

Page 2

$Page 2 I N T R O D U C T I O N 2 CAUTION! Please read the following manual before assembling and operating your ErgoArm Tool Support System\b As in all cases, when electric or air lines come in close contact with moving parts or mechanisms, precautions should be taken by the person installing and operating the equipment that these cords or hoses do not become entangled or damaged by moving parts\b Proper attention will prevent possible hazard or injury. R E C O M M E N D E D T O O L S \b...$

I N T R O D U C T I O N
2
CAUTION!
Please read the following manual before assembling and operating your ErgoArm Tool Support System\b
As  in  all  cases,  when  electric  or  air  lines  come  in  close  contact  with  moving  parts  or  mechanisms,  precautions  should  be
taken by the person installing and operating the equipment that these cords or hoses do not become entangled or damaged
by moving parts\b Proper attention will prevent possible hazard or injury.
R E C O M M E N D E D   T O O L S   \b...

Page 3

$Page 3 3 I N S T A L L A T I O N A N D S E T U P I N S T U C T I O N S - A L L M O D E L S 1.Remove the TABLE MOUNT from the box\b \b. Bolt to work surface\b It is important to level the table mount so that the post is 90 degrees to the work surface through full range of travel (see VIEW #1) 3. Insert POSTinto mount, and tighten set screws\b 4. Remove remaining body of ErgoArm from box and slide ADJUSTABLE SHOULDER CLAMPover POST\b Tighten screws at desired height (see VIEW...$

3
I N S T A L L A T I O N   A N D   S E T   U P   I N S T U C T I O N S   -   A L L   M O D E L S
1.Remove  the TABLE MOUNT from the box\b
\b. Bolt to work surface\b It is important to level the table mount so that the post is 90 degrees to the work surface through full range of
travel (see VIEW #1)
3. Insert  POSTinto mount, and tighten set screws\b
4. Remove  remaining  body  of  ErgoArm  from  box  and  slide  ADJUSTABLE  SHOULDER  CLAMPover POST\b  Tighten  screws  at  desired
height  (see VIEW...

Page 4

$Page 4 4 I N S T A L L A T I O N A N D S E T U P I N S T U C T I O N S - A L L M O D E L S The VERTICAL ADJUSTMENT ROD (Item #41) allows the tool to be adjusted from zero degrees (parallel to column), up to 15 degrees in either direction from zero point\b This compensates for any irregularities in the workpiece or if application requires fastener to be driven in at an angle (see View #3)\b This does not take the place of properly leveling the Table Mount Flange\b Use for ﬁnal 90 degree...$

4
I N S T A L L A T I O N   A N D   S E T   U P   I N S T U C T I O N S   -   A L L   M O D E L S
The VERTICAL ADJUSTMENT ROD (Item #41) allows the tool to be adjusted from zero degrees (parallel to column), up to 15 degrees
in either direction from zero point\b This compensates for any irregularities in the workpiece or if application requires fastener to be 
driven in at an angle (see View #3)\b This does not take the place of properly leveling the Table Mount Flange\b Use for ﬁnal 90 degree...

Page 5

$Page 5 \b I N S T A L L A T I O N A N D S E T U P I N S T U C T I O N S - A L L M O D E L S To increase the reach capability of the ErgoArm, remove the ring pin (Item #14) from the CYLINDER MOUNTING YOKEROD END (Item #1\f)\b Pull the FOREARM INSERT (Item #13) out, away from the arm, the desired reach, up to an additional 5\b Once desired reach is achieved, align holes in FOREARMand FOREARM INSERT, reinsert ring pin in CYLINDER MOUNTING YOKEROD END (Item...$

\b
I N S T A L L A T I O N   A N D   S E T   U P   I N S T U C T I O N S   -   A L L   M O D E L S
To  increase  the  reach  capability  of  the  ErgoArm,  remove  the  ring  pin  (Item  #14)  from  the CYLINDER  MOUNTING  YOKEROD  END
(Item #1\f)\b
Pull  the  FOREARM  INSERT (Item  #13)  out,  away  from  the  arm,  the  desired  reach,  up  to  an  additional  5\b  Once  desired  reach  is 
achieved, align holes in  FOREARMand FOREARM INSERT, reinsert ring pin in  CYLINDER MOUNTING YOKEROD END (Item...

Page 6

$Page 6 6 PAR TS B R EAK DO W N Ergo Arm Operations \:Manual_3000 nutrunner\: manual.qxd \f/\b/2013\: \f:46 AM Page 6$

6
PAR TS  B R EAK DO W N
Ergo Arm Operations \:Manual_3000 nutrunner\: manual.qxd  \f/\b/2013\:  \f:46 AM  Page 6

Page 7

$Page 7 7 P A R T S B R E A K D O W N Ergo Arm Operations \:Manual_3000 nutrunner\: manual.qxd \f/\b/2013\: \f:46 AM Page 7$

7
P A R T S   B R E A K D O W N
Ergo Arm Operations \:Manual_3000 nutrunner\: manual.qxd  \f/\b/2013\:  \f:46 AM  Page 7

Page 8

$Page 8 E R G O - A R M B R E A K D O W N Index PartNu\fber Nu\fberDes\briptionQty 1 EA14Table Flange1 2 EA01 Post1 \f EA02 Shoulder Clamp1 4 EA44 1\b420 x 11\b4 Cap Screw 2 5 EA0\f Bearing4 6 EA04 1\b21\f x 4 Double Ended Stud 2 7 EA05 1\b21\f Locking Nut 2 8 EA21 Label2 9 EA06 Upper Arm 1 10 EA07 Elbow1 11 EA10 Forearm1 12 EA09 Cyl. Mtg. Yoke Rod End 1 1\f EA11 Forearm Insert1 14 EA18 1\b4 x 15\b8 Cotterless Clevis Pin 1 15 EA17 \f\b16 x \f\b4 Clevis Pin 1 16 EA1\f Hair Pin Cotter1 17 EA20 8\f2 x...$

E R G O - A R M   B R E A K D O W N
Index PartNu\fber Nu\fberDes\briptionQty
1 EA14Table Flange1
2 EA01 Post1
\f  EA02 Shoulder Clamp1
4  EA44 1\b420 x 11\b4 Cap Screw 2
5  EA0\f Bearing4
6 EA04 1\b21\f x 4 Double Ended Stud 2
7 EA05 1\b21\f Locking Nut 2
8  EA21 Label2
9  EA06 Upper Arm 1
10  EA07 Elbow1
11 EA10 Forearm1
12  EA09 Cyl. Mtg. Yoke Rod End 1
1\f EA11 Forearm Insert1
14  EA18 1\b4 x 15\b8 Cotterless Clevis Pin 1
15  EA17 \f\b16 x \f\b4 Clevis Pin 1
16  EA1\f Hair Pin Cotter1
17  EA20 8\f2 x...

Page 9

Notes:

Page 10

Start reading Aimco Brakes Assembly System ERGOARM Tool Support Systems Operation Manual

Related Manuals for Aimco Brakes Assembly System ERGOARM Tool Support Systems Operation Manual

All Aimco Brakes manuals