Air Live Router WL-5470AP User Manual

AirLive WL_5470AP User’s Manual 
6 
 
 
 
 
 
3.2 Client Mode (Infrastructure) 
If set to Client (Infrastructure) mode, this device can work like a wireless station when it’s connected to a 
computer so that the computer can send packets from wired end to wireless interface. 
Refer to the illustration below. This station (AP1 plus the connected computer 1) can associate to another 
Access Point (AP2), and then can have the Internet access if the other Access Point (AP2) has the Internet 
connection. 
  

                                                                     AirLive WL_5470AP User’s Manual 
7  To set the operation mode to “Client (Infrastructure)”, Please go to “Mode JClient” and click the Setup 
button. 
In the “Network Type” field, select as “infrastructure” for configuration. 
 
 
3.3 Client Mode (Ad-hoc) 
If set to the Client (Ad-hoc) mode, this device can work like a wireless station when it is connected to a 
computer so that the computer can send packets from wired end to wireless...

AirLive WL_5470AP User’s Manual 
8  To set the operation mode to “Client (Ad-Hoc)”, Please go to “Mode JClient” and click the Setup button. 
In the “Network Type” field, select as “infrastructure” for configuration. 
 
3.4 Bridge Mode 
In this mode, 2 access points in two remote locations connect to each other to provide a wireless bridge 
between 2 remote LANs. It is mostly used by enterprise to connect 2 remote offices network together. The 
bridge modes are connected by using either the WDS (Wireless...

                                                                     AirLive WL_5470AP User’s Manual 
9 
3.5 WDS Repeater Mode 
A repeaters function is to extend the wireless coverage of another wireless AP or router. 
For WDS repeater to work, the remote wireless AP/Router must also support WDS function. 
 
To set the operation mode to “WDS Repeater”, Please go to “Mode JWDS Repeater” and click the Setup 
button for configuration. 
 
 
3.6 Universal Repeater Mode 
A universal repeater can also extend...

AirLive WL_5470AP User’s Manual 
10  To set the operation mode to “Universal Repeater”, Please go to “Mode JUniversal Repeater” and click 
the Setup button for configuration. 
 
 
3.7 WISP ( Client Router) Mode 
z WISP (Client Router) mode 
In WISP mode, the AP will behave just the same as the Client mode for wireless function. However, Router 
functions are added between the wireless WAN side and the Ethernet LAN side. Therefore, The WISP 
subscriber can share the WISP connection without the need for...

                                                                     AirLive WL_5470AP User’s Manual 
11 
3.8 WISP + Universal Repeater Mode 
In this mode, the AP behaves virtually the same as the WISP mode, except one thing: the AP can also send 
wireless signal to the LAN side. That means the AP can connect with the remote WISP AP and the indoor 
wireless card, and then provide IP sharing capability all at the same time! However, the output power is 
divided between 2 wireless sides and proper antenna...

AirLive WL_5470AP User’s Manual 
12  To set the operation mode to “GW Mode”, Please go to “Mode JGW” and click the Setup button 
for configuration. 
 
 
 
 
 
 
 
 
 
 
 
 
  

                                                                     AirLive WL_5470AP User’s Manual 
13 
Chapter IV: Configuration   
1.  Start your computer. Connect an Ethernet cable between your computer and the Wireless Access Point. 
2.  Make sure your wired station is set to the same subnet as the Wireless Access Point, i.e. 192.168.100.X 
3.  Start your WEB browser. In the Address box, enter the following: 
http://192.168.100.252/
 
 
The configuration menu is divided into five categories:...

AirLive WL_5470AP User’s Manual 
14 
4.1 Mode 
You can choose and setup different wireless mode for detail configurations 
 
 
Wireless Mode    
AP Select the AP and press Setup button for Wireless AP mode configuration. 
 
Client Select the Client and press Setup button for Wireless Client mode 
configuration. 
Bridge Select the Bridge and press Setup button for Wireless Bridge mode 
configuration. 
WDS Repeater Select the WDS Repeater and press Setup button for Wireless WDS Repeater 
mode...

                                                                     AirLive WL_5470AP User’s Manual 
15 
4.2 AP Mode Setting 
 
Alias Name You can set the alias name for this device. Limited not exceed 32 characters. 
… Disable Wireless 
   LAN Interface Check the box to disable the Wireless LAN Interface, by so doing; you won’t be able 
to make wireless connection with this Access Point in your located network. In other 
words, this device will not be visible by any wireless station. 
Band You can...