Aleratec 111 HDD Copy Cruiser 11 Hard Disk Drive Duplicator and 12 HDD Sanitizer User Guide

www.aleratec.com15
Using the 1:11 HDD Copy Cruiser 
Main Menu
Compare HDD
The “Compare HDD” function performs a comparison of data from the source hard 
drive to the data on the target hard drives. 
1. With the source and target HDDs loaded use the arrow buttons (or) to 
select “Compare HDD”. The following screen will be displayed. 
2. Press ENT to begin the comparison. The system will auto-detect the hard 
drives.  
During the compare process, the 1:11 HDD Copy Cruiser will display progress...

www.aleratec.com16
Using the 1:11 HDD Copy Cruiser 
Main Menu
Async Compare
The function “Async Compare” allows you to insert target drives for data comparing 
during the comparing operation. During the process, you can insert another drive as 
a target of the Async Compare operation and the unit will automatically compare 
this new drive as well. 
1. With the source and target HDDs loaded use the arrow buttons (or) to 
select “Async Compare”. The following screen will be displayed. 
2. Press ENT to...

www.aleratec.com17
Using the 1:11 HDD Copy Cruiser 
Main Menu
PreScan Source
The “PreScan Source” scans the source hard drive to determine if it can be read 
correctly.  
1. With the source HDD loaded, use the arrow buttons (or) to select “PreScan 
Source”. The following screen will be displayed. 
2. Press ENT to begin the scan. The system will auto-detect the hard drives. 
During the PreScan process, the 1:11 HDD Copy Cruiser will display progress 
information. 
3. When the PreScan is complete, a job...

www.aleratec.com18
Using the 1:11 HDD Copy Cruiser 
Main Menu
ReScan Bus
The “ReScan Bus” function causes the 1:11 HDD Copy Cruiser to redetect connected 
hard drives. This can be used when you change drives without restarting the system. 
1. Use the arrow buttons (or) to select “ReScan BUS”. The following screen 
will be displayed.  
2. Press ENT to select. The system will prompt you to confirm that you wish to 
proceed.  
3. Press ENT	to begin the rescan, during which the following screen will be...

www.aleratec.com19
Using the 1:11 HDD Copy Cruiser 
Main Menu
Source HDD Size
The “Source size” function is used to display the capacity of the source hard drive. 
1. With the source HDD loaded, use the arrow buttons (or) to select “Source 
size”. The following screen will be displayed.  
2. Press ENT	to display the capacity of the source hard drive. 
ENTESC


7. Source size
ENTESC


Total: 232.5GB  

www.aleratec.com20
Using the 1:11 HDD Copy Cruiser 
Main Menu
Secure Erase
The “Secure Erase” function will sanitize (wipe clean of all data) the hard disk 
drives connected to the 1:11 HDD Copy Cruiser using algorithms programmed by 
the hard drive manufacturer.  Since this function is native to the hard drive, it is very 
fast and reliable.  Almost all modern SATA hard drives support this feature.  In the 
rare case that Secure Erase is not supported, please use the “Overwrite” function to 
sanitize...

www.aleratec.com21
ENTESC


1 HDD          CH:0Wipe successful
 
 
5. You can now scroll up and down for the individual status of each drive.  
Using the 1:11 HDD Copy Cruiser 
 
 
 
 
 
 
 
   

www.aleratec.com22
Using the 1:11 HDD Copy Cruiser 
Main Menu
Overwrite
The “Overwrite” function will sanitize (wipe clean of all data) the hard disk drives 
connected to the 1:11 HDD Copy Cruiser. 
1. Load up to 12 HDDs into the 1:11 HDD Copy Cruiser. The system will auto-
detect the hard drives. Using the arrow buttons (or) select “Overwrite”. 
The following screen will be displayed. 
Note: Overwriting the entire capacity of all connected hard drives can take an extended period of time.
2. Press ENT...

www.aleratec.com23
Using the 1:11 HDD Copy Cruiser 
b. To perform a “Three Pass Overwrite”, scroll to “3 Pass” and press ENT. 
This method will write one pass of 1’s, one pass of zeros, and one pass of  
randomly generated data. 
The next screen allows you to choose whether you wish to verify the 
random overwrite. 
Use the arrow buttons to toggle between “On” and “Off”. Press ENT to 
select.
c. To perform a “Seven Pass Overwrite”, scroll to “7 Pass” and press ENT. 
The following screen will be...

www.aleratec.com24
Using the 1:11 HDD Copy Cruiser 
Main Menu
Setup
The “Setup” menu contains configuration options for the 1:11 HDD Copy Cruiser. It 
is suggested to use the factory defaults for optimum performance. 
1. Use the arrow buttons (or) to select “Setup”. Press ENT to select. The 
following screen will be displayed. 
Note: After changing any of the configuration options, you must press ENT to accept the change. Once all changes are complete, press ESC to exit the Setup menu. The following...